From: Al Cooper <alcooperx@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: Al Cooper <alcooperx@gmail.com>,
bcm-kernel-feedback-list@broadcom.com,
devicetree@vger.kernel.org,
Florian Fainelli <f.fainelli@gmail.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
linux-arm-kernel@lists.infradead.org,
Mark Rutland <mark.rutland@arm.com>,
Rob Herring <robh+dt@kernel.org>,
Srinath Mannam <srinath.mannam@broadcom.com>
Subject: [PATCH v3 13/13] phy: usb: Add support for wake and USB low power mode for 7211 S2/S5
Date: Tue, 10 Dec 2019 08:21:32 -0500 [thread overview]
Message-ID: <20191210132132.41509-14-alcooperx@gmail.com> (raw)
In-Reply-To: <20191210132132.41509-1-alcooperx@gmail.com>
Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.
On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
.../phy/broadcom/phy-brcm-usb-init-synopsis.c | 77 +++++++++++++++++--
drivers/phy/broadcom/phy-brcm-usb-init.c | 26 ++++---
drivers/phy/broadcom/phy-brcm-usb-init.h | 11 +--
drivers/phy/broadcom/phy-brcm-usb.c | 25 ++++--
4 files changed, 105 insertions(+), 34 deletions(-)
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index c6504649d307..a2f96fce8c2f 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -26,7 +26,6 @@
#define PIARBCTL_MISC_CAM1_MEM_PAGE_MASK 0x00000f00
#define PIARBCTL_MISC_CAM0_MEM_PAGE_MASK 0x000000f0
#define PIARBCTL_MISC_SATA_PRIORITY_MASK 0x0000000f
-#define PIARBCTL_USB_M_ASB_CTRL 0x10
#define PIARBCTL_MISC_USB_ONLY_MASK \
(PIARBCTL_MISC_USB_SELECT_MASK | \
@@ -51,14 +50,27 @@
#define USB_CTRL_USB_PM_STATUS 0x08
#define USB_CTRL_USB_DEVICE_CTL1 0x10
#define USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK 0x00000003
+#define USB_CTRL_TEST_PORT_CTL 0x30
+#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_MASK 0x000000ff
+#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_PME_GEN_MASK 0x0000002e
+#define USB_CTRL_TP_DIAG1 0x34
+#define USB_CTLR_TP_DIAG1_wake_MASK 0x00000002
+#define USB_CTRL_CTLR_CSHCR 0x50
+#define USB_CTRL_CTLR_CSHCR_ctl_pme_en_MASK 0x00040000
/* Register definitions for the USB_PHY block in 7211b0 */
+#define USB_PHY_PLL_CTL 0x00
+#define USB_PHY_PLL_CTL_PLL_RESETB_MASK 0x40000000
#define USB_PHY_PLL_LDO_CTL 0x08
#define USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK 0x00000004
+#define USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK 0x00000002
+#define USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK 0x00000001
#define USB_PHY_UTMI_CTL_1 0x04
#define USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK 0x00000800
#define USB_PHY_UTMI_CTL_1_PHY_MODE_MASK 0x0000000c
#define USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT 2
+#define USB_PHY_IDDQ 0x1c
+#define USB_PHY_IDDQ_phy_iddq_MASK 0x00000001
#define USB_PHY_STATUS 0x20
#define USB_PHY_STATUS_pll_lock_MASK 0x00000001
@@ -199,6 +211,17 @@ static void usb_init_common(struct brcm_usb_init_params *params)
}
}
+static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params,
+ bool enable)
+{
+ void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+ if (enable)
+ USB_CTRL_SET(ctrl, CTLR_CSHCR, ctl_pme_en);
+ else
+ USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
+}
+
static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
@@ -210,9 +233,27 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
if (params->syscon_piarbctl)
syscon_piarbctl_init(params->syscon_piarbctl);
+ USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+
+ usb_wake_enable_7211b0(params, false);
+ if (!params->wake_enabled) {
+
+ /* undo possible suspend settings */
+ brcm_usb_writel(0, usb_phy + USB_PHY_IDDQ);
+ reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
+ reg |= USB_PHY_PLL_CTL_PLL_RESETB_MASK;
+ brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
+
+ /* temporarily enable FSM so PHY comes up properly */
+ reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+ reg |= USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
+ brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+ }
+
/* Init the PHY */
- reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_LDO_CTL);
- reg |= USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK;
+ reg = USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK |
+ USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK |
+ USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK;
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
/* wait for lock */
@@ -276,12 +317,36 @@ static void usb_uninit_common(struct brcm_usb_init_params *params)
}
+static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
+{
+ void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+ void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+ u32 reg;
+
+ pr_debug("%s\n", __func__);
+
+ if (params->wake_enabled) {
+ USB_CTRL_SET(ctrl, TEST_PORT_CTL, TPOUT_SEL_PME_GEN);
+ usb_wake_enable_7211b0(params, true);
+ } else {
+ USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+ brcm_usb_writel(0, usb_phy + USB_PHY_PLL_LDO_CTL);
+ reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
+ reg &= ~USB_PHY_PLL_CTL_PLL_RESETB_MASK;
+ brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
+ brcm_usb_writel(USB_PHY_IDDQ_phy_iddq_MASK,
+ usb_phy + USB_PHY_IDDQ);
+ }
+
+}
+
static void usb_uninit_xhci(struct brcm_usb_init_params *params)
{
pr_debug("%s\n", __func__);
- xhci_soft_reset(params, 1);
+ if (!params->wake_enabled)
+ xhci_soft_reset(params, 1);
}
static int usb_get_dual_select(struct brcm_usb_init_params *params)
@@ -309,7 +374,6 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
}
-
static const struct brcm_usb_init_ops bcm7216_ops = {
.init_ipp = usb_init_ipp,
.init_common = usb_init_common,
@@ -324,7 +388,7 @@ static const struct brcm_usb_init_ops bcm7211b0_ops = {
.init_ipp = usb_init_ipp,
.init_common = usb_init_common_7211b0,
.init_xhci = usb_init_xhci,
- .uninit_common = usb_uninit_common,
+ .uninit_common = usb_uninit_common_7211b0,
.uninit_xhci = usb_uninit_xhci,
.get_dual_select = usb_get_dual_select,
.set_dual_select = usb_set_dual_select,
@@ -346,4 +410,5 @@ void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
params->family_name = "7211";
params->ops = &bcm7211b0_ops;
+ params->suspend_with_clocks = true;
}
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 17acc3c1051b..9391ab42a12b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -783,12 +783,24 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
msleep(50);
}
+static void usb_wake_enable(struct brcm_usb_init_params *params,
+ bool enable)
+{
+ void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+ if (enable)
+ USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
+ else
+ USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
+}
+
static void usb_init_common(struct brcm_usb_init_params *params)
{
u32 reg;
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
/* Clear any pending wake conditions */
+ usb_wake_enable(params, false);
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
@@ -935,6 +947,8 @@ static void usb_uninit_common(struct brcm_usb_init_params *params)
if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN))
USB_CTRL_SET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
+ if (params->wake_enabled)
+ usb_wake_enable(params, true);
}
static void usb_uninit_eohci(struct brcm_usb_init_params *params)
@@ -978,17 +992,6 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
}
}
-static void usb_wake_enable(struct brcm_usb_init_params *params,
- int enable)
-{
- void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
-
- if (enable)
- USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
- else
- USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
-}
-
static const struct brcm_usb_init_ops bcm7445_ops = {
.init_ipp = usb_init_ipp,
.init_common = usb_init_common,
@@ -999,7 +1002,6 @@ static const struct brcm_usb_init_ops bcm7445_ops = {
.uninit_xhci = usb_uninit_xhci,
.get_dual_select = usb_get_dual_select,
.set_dual_select = usb_set_dual_select,
- .wake_enable = usb_wake_enable,
};
void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 4cdd9cc1c5a3..899b9eb43fad 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -46,8 +46,6 @@ struct brcm_usb_init_ops {
void (*uninit_xhci)(struct brcm_usb_init_params *params);
int (*get_dual_select)(struct brcm_usb_init_params *params);
void (*set_dual_select)(struct brcm_usb_init_params *params, int mode);
- void (*wake_enable)(struct brcm_usb_init_params *params,
- int enable);
};
struct brcm_usb_init_params {
@@ -62,6 +60,8 @@ struct brcm_usb_init_params {
const u32 *usb_reg_bits_map;
const struct brcm_usb_init_ops *ops;
struct regmap *syscon_piarbctl;
+ bool wake_enabled;
+ bool suspend_with_clocks;
};
void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
@@ -145,13 +145,6 @@ static inline void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini)
ini->ops->uninit_xhci(ini);
}
-static inline void brcm_usb_wake_enable(struct brcm_usb_init_params *ini,
- int enable)
-{
- if (ini->ops->wake_enable)
- ini->ops->wake_enable(ini, enable);
-}
-
static inline int brcm_usb_get_dual_select(struct brcm_usb_init_params *ini)
{
if (ini->ops->get_dual_select)
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 1ab44f54244b..491bbd46c5b3 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -535,16 +535,26 @@ static int brcm_usb_phy_suspend(struct device *dev)
struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
if (priv->init_count) {
+ priv->ini.wake_enabled = device_may_wakeup(dev);
if (priv->phys[BRCM_USB_PHY_3_0].inited)
brcm_usb_uninit_xhci(&priv->ini);
if (priv->phys[BRCM_USB_PHY_2_0].inited)
brcm_usb_uninit_eohci(&priv->ini);
brcm_usb_uninit_common(&priv->ini);
- brcm_usb_wake_enable(&priv->ini, true);
- if (priv->phys[BRCM_USB_PHY_3_0].inited)
- clk_disable_unprepare(priv->usb_30_clk);
- if (priv->phys[BRCM_USB_PHY_2_0].inited || !priv->has_eohci)
- clk_disable_unprepare(priv->usb_20_clk);
+
+ /*
+ * Handle the clocks unless needed for wake. This has
+ * to work for both older XHCI->3.0-clks, EOHCI->2.0-clks
+ * and newer XHCI->2.0-clks/3.0-clks.
+ */
+
+ if (!priv->ini.suspend_with_clocks) {
+ if (priv->phys[BRCM_USB_PHY_3_0].inited)
+ clk_disable_unprepare(priv->usb_30_clk);
+ if (priv->phys[BRCM_USB_PHY_2_0].inited ||
+ !priv->has_eohci)
+ clk_disable_unprepare(priv->usb_20_clk);
+ }
if (priv->wake_irq >= 0)
enable_irq_wake(priv->wake_irq);
}
@@ -557,7 +567,6 @@ static int brcm_usb_phy_resume(struct device *dev)
clk_prepare_enable(priv->usb_20_clk);
clk_prepare_enable(priv->usb_30_clk);
- brcm_usb_wake_enable(&priv->ini, false);
brcm_usb_init_ipp(&priv->ini);
/*
@@ -579,6 +588,8 @@ static int brcm_usb_phy_resume(struct device *dev)
} else if (priv->has_xhci) {
brcm_usb_uninit_xhci(&priv->ini);
clk_disable_unprepare(priv->usb_30_clk);
+ if (!priv->has_eohci)
+ clk_disable_unprepare(priv->usb_20_clk);
}
} else {
if (priv->has_xhci)
@@ -589,7 +600,7 @@ static int brcm_usb_phy_resume(struct device *dev)
clk_disable_unprepare(priv->usb_20_clk);
clk_disable_unprepare(priv->usb_30_clk);
}
-
+ priv->ini.wake_enabled = false;
return 0;
}
#endif /* CONFIG_PM_SLEEP */
--
2.17.1
next prev parent reply other threads:[~2019-12-10 13:24 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-10 13:21 [PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver Al Cooper
2019-12-10 13:21 ` [PATCH v3 01/13] phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family Al Cooper
2019-12-10 13:21 ` [PATCH v3 02/13] phy: usb: Get all drivers that use USB clks using correct enable/disable Al Cooper
2019-12-10 13:21 ` [PATCH v3 03/13] phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode Al Cooper
2019-12-10 13:21 ` [PATCH v3 04/13] phy: usb: Add "wake on" functionality Al Cooper
2019-12-10 13:21 ` [PATCH v3 05/13] phy: usb: Restructure in preparation for adding 7216 USB support Al Cooper
2019-12-10 13:21 ` [PATCH v3 06/13] dt-bindings: Add Broadcom STB USB PHY binding document Al Cooper
2019-12-13 19:10 ` Rob Herring
2019-12-10 13:21 ` [PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216 Al Cooper
2020-01-03 9:33 ` Kishon Vijay Abraham I
2020-01-03 13:06 ` Alan Cooper
2019-12-10 13:21 ` [PATCH v3 08/13] phy: usb: Add support for new Synopsis USB controller on the 7211b0 Al Cooper
2019-12-10 13:21 ` [PATCH v3 09/13] phy: usb: fix driver to defer on clk_get defer Al Cooper
2019-12-10 13:21 ` [PATCH v3 10/13] phy: usb: PHY's MDIO registers not accessible without device installed Al Cooper
2019-12-10 13:21 ` [PATCH v3 11/13] phy: usb: bdc: Fix occasional failure with BDC on 7211 Al Cooper
2019-12-10 13:21 ` [PATCH v3 12/13] phy: usb: USB driver is crashing during S3 resume on 7216 Al Cooper
2019-12-10 13:21 ` Al Cooper [this message]
2019-12-13 19:25 ` [PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver Florian Fainelli
2019-12-31 17:41 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191210132132.41509-14-alcooperx@gmail.com \
--to=alcooperx@gmail.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=srinath.mannam@broadcom.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).