From: Biao Huang <biao.huang@mediatek.com>
To: <davem@davemloft.net>, Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>,
Giuseppe Cavallaro <peppe.cavallaro@st.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
Jose Abreu <joabreu@synopsys.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Biao Huang <biao.huang@mediatek.com>, <netdev@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>, <yt.shen@mediatek.com>
Subject: [PATCH 1/2] net-next: stmmac: mediatek: add more suuport for RMII
Date: Thu, 12 Dec 2019 10:41:44 +0800 [thread overview]
Message-ID: <20191212024145.21752-2-biao.huang@mediatek.com> (raw)
In-Reply-To: <20191212024145.21752-1-biao.huang@mediatek.com>
MT2712 SoC can provide the rmii reference clock, and the clock
will output from TXC pin only, which means ref_clk pin of external
PHY should connect to TXC pin in this case.
Add corresponding clock and timing settings.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
.../ethernet/stmicro/stmmac/dwmac-mediatek.c | 85 +++++++++++++------
1 file changed, 60 insertions(+), 25 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index bdb80421acac..af24954c7654 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -51,10 +51,12 @@ struct mediatek_dwmac_plat_data {
const struct mediatek_dwmac_variant *variant;
struct mac_delay_struct mac_delay;
struct clk_bulk_data *clks;
+ struct clk *mac_rmii_clk;
struct device_node *np;
struct regmap *peri_regmap;
struct device *dev;
phy_interface_t phy_mode;
+ bool rmii_clk_from_mac;
bool rmii_rxc;
};
@@ -78,6 +80,7 @@ static const char * const mt2712_dwmac_clk_l[] = {
static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
{
+ int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0;
int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0;
u32 intf_val = 0;
@@ -87,7 +90,7 @@ static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
intf_val |= PHY_INTF_MII;
break;
case PHY_INTERFACE_MODE_RMII:
- intf_val |= (PHY_INTF_RMII | rmii_rxc);
+ intf_val |= (PHY_INTF_RMII | rmii_rxc | rmii_clk_from_mac);
break;
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_TXID:
@@ -173,35 +176,50 @@ static int mt2712_set_delay(struct mediatek_dwmac_plat_data *plat)
delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
break;
case PHY_INTERFACE_MODE_RMII:
- /* the rmii reference clock is from external phy,
- * and the property "rmii_rxc" indicates which pin(TXC/RXC)
- * the reference clk is connected to. The reference clock is a
- * received signal, so rx_delay/rx_inv are used to indicate
- * the reference clock timing adjustment
- */
- if (plat->rmii_rxc) {
- /* the rmii reference clock from outside is connected
- * to RXC pin, the reference clock will be adjusted
- * by RXC delay macro circuit.
- */
- delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
- delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
- delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
- } else {
- /* the rmii reference clock from outside is connected
- * to TXC pin, the reference clock will be adjusted
- * by TXC delay macro circuit.
+ if (plat->rmii_clk_from_mac) {
+ /* case 1: mac provides the rmii reference clock,
+ * and the clock output to TXC pin.
+ * The egress timing can be adjusted by GTXC delay macro circuit.
+ * The ingress timing can be adjusted by TXC delay macro circuit.
*/
delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay);
delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay);
delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv);
+
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_INV, mac_delay->tx_inv);
+ } else {
+ /* case 2: the rmii reference clock is from external phy,
+ * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+ * the reference clk is connected to. The reference clock is a
+ * received signal, so rx_delay/rx_inv are used to indicate
+ * the reference clock timing adjustment
+ */
+ if (plat->rmii_rxc) {
+ /* the rmii reference clock from outside is connected
+ * to RXC pin, the reference clock will be adjusted
+ * by RXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
+ } else {
+ /* the rmii reference clock from outside is connected
+ * to TXC pin, the reference clock will be adjusted
+ * by TXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv);
+ }
+ /* tx_inv will inverse the tx clock inside mac relateive to
+ * reference clock from external phy,
+ * and this bit is located in the same register with fine-tune
+ */
+ if (mac_delay->tx_inv)
+ fine_val = ETH_RMII_DLY_TX_INV;
}
- /* tx_inv will inverse the tx clock inside mac relateive to
- * reference clock from external phy,
- * and this bit is located in the same register with fine-tune
- */
- if (mac_delay->tx_inv)
- fine_val = ETH_RMII_DLY_TX_INV;
break;
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_TXID:
@@ -278,6 +296,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
mac_delay->tx_inv = of_property_read_bool(plat->np, "mediatek,txc-inverse");
mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
+ plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac");
return 0;
}
@@ -287,6 +306,16 @@ static int mediatek_dwmac_clk_init(struct mediatek_dwmac_plat_data *plat)
const struct mediatek_dwmac_variant *variant = plat->variant;
int i, num = variant->num_clks;
+ plat->mac_rmii_clk = NULL;
+ if (plat->phy_mode == PHY_INTERFACE_MODE_RMII &&
+ plat->rmii_clk_from_mac) {
+ plat->mac_rmii_clk = devm_clk_get(plat->dev, "rmii_internal");
+ if (IS_ERR(plat->mac_rmii_clk)) {
+ dev_err(plat->dev, "Failed to get reference clk from MAC\n");
+ return PTR_ERR(plat->mac_rmii_clk);
+ }
+ }
+
plat->clks = devm_kcalloc(plat->dev, num, sizeof(*plat->clks), GFP_KERNEL);
if (!plat->clks)
return -ENOMEM;
@@ -327,6 +356,9 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
return ret;
}
+ if (plat->mac_rmii_clk)
+ clk_prepare_enable(plat->mac_rmii_clk);
+
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
@@ -338,6 +370,9 @@ static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
struct mediatek_dwmac_plat_data *plat = priv;
const struct mediatek_dwmac_variant *variant = plat->variant;
+ if (plat->mac_rmii_clk)
+ clk_disable_unprepare(plat->mac_rmii_clk);
+
clk_bulk_disable_unprepare(variant->num_clks, plat->clks);
pm_runtime_put_sync(&pdev->dev);
--
2.18.0
next prev parent reply other threads:[~2019-12-12 2:42 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-12 2:41 [PATCH 0/2] net-next: stmmac: dwmac-mediatek: add more support for RMII Biao Huang
2019-12-12 2:41 ` Biao Huang [this message]
2019-12-12 13:25 ` [PATCH 1/2] net-next: stmmac: mediatek: add more suuport " Andrew Lunn
[not found] ` <1576200981.29387.13.camel@mhfsdcap03>
2019-12-13 13:47 ` Andrew Lunn
2019-12-12 2:41 ` [PATCH 2/2] net-next: dt-binding: dwmac-mediatek: add more description " Biao Huang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191212024145.21752-2-biao.huang@mediatek.com \
--to=biao.huang@mediatek.com \
--cc=alexandre.torgue@st.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=joabreu@synopsys.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=peppe.cavallaro@st.com \
--cc=robh+dt@kernel.org \
--cc=yt.shen@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).