From: "周琰杰 (Zhou Yanjie)" <zhouyanjie@wanyeetech.com>
To: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
robh+dt@kernel.org, paul.burton@mips.com, paulburton@kernel.org,
jhogan@kernel.org, mark.rutland@arm.com, syq@debian.org,
ralf@linux-mips.org, rick.tyliu@ingenic.com,
jason@lakedaemon.net, keescook@chromium.org,
geert+renesas@glider.be, krzk@kernel.org, paul@crapouillou.net,
prasannatsmkumar@gmail.com, sernia.zhou@foxmail.com,
zhenwenjin@gmail.com, ebiederm@xmission.com
Subject: [PATCH 1/2] MIPS: Ingenic: Add missing nodes for X1000 and CU1000-Neo.
Date: Wed, 15 Jan 2020 01:03:47 +0800 [thread overview]
Message-ID: <1579021428-43535-3-git-send-email-zhouyanjie@wanyeetech.com> (raw)
In-Reply-To: <1579021428-43535-1-git-send-email-zhouyanjie@wanyeetech.com>
Add I2C0/I2C1/I2C2 nodes for X1000 and add I2C0, ADS7830,
MSC1, AP6212A, wlan_pwrseq nodes for CU1000-Neo.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
arch/mips/boot/dts/ingenic/cu1000-neo.dts | 71 +++++++++++++++++++++++++++++++
arch/mips/boot/dts/ingenic/x1000.dtsi | 45 ++++++++++++++++++++
2 files changed, 116 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
index b0733da..03abd94 100644
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -4,6 +4,7 @@
#include "x1000.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
compatible = "yna,cu1000-neo", "ingenic,x1000";
@@ -21,6 +22,22 @@
device_type = "memory";
reg = <0x0 0x04000000>;
};
+
+ wlan_pwrseq: msc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+
+ clocks = <&lpoclk>;
+ clock-names = "ext_clock";
+
+ reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+
+ lpoclk: ap6212a {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
};
&exclk {
@@ -36,6 +53,20 @@
ingenic,pwm-channels-mask = <0xfa>;
};
+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_i2c0>;
+
+ ads7830@48 {
+ compatible = "ti,ads7830";
+ reg = <0x48>;
+ };
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pins_uart2>;
@@ -78,7 +109,41 @@
status = "okay";
};
+&msc1 {
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ non-removable;
+
+ mmc-pwrseq = <&wlan_pwrseq>;
+
+ status = "okay";
+
+ ap6212a: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupt-parent = <&gpc>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ brcm,drive-strength = <10>;
+ };
+};
+
&pinctrl {
+ pins_i2c0: i2c0 {
+ function = "i2c0";
+ groups = "i2c0-data";
+ bias-disable;
+ };
+
pins_uart2: uart2 {
function = "uart2";
groups = "uart2-data-d";
@@ -96,4 +161,10 @@
groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
bias-disable;
};
+
+ pins_msc1: msc1 {
+ function = "mmc1";
+ groups = "mmc1-1bit", "mmc1-4bit";
+ bias-disable;
+ };
};
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index ea54263..376df1b 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -169,6 +169,51 @@
};
};
+ i2c0: i2c-controller@10050000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10050000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <60>;
+
+ clocks = <&cgu X1000_CLK_I2C0>;
+
+ status = "disabled";
+ };
+
+ i2c1: i2c-controller@10051000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10051000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <59>;
+
+ clocks = <&cgu X1000_CLK_I2C1>;
+
+ status = "disabled";
+ };
+
+ i2c2: i2c-controller@10052000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10052000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <58>;
+
+ clocks = <&cgu X1000_CLK_I2C2>;
+
+ status = "disabled";
+ };
+
uart0: serial@10030000 {
compatible = "ingenic,x1000-uart";
reg = <0x10030000 0x100>;
--
2.7.4
next prev parent reply other threads:[~2020-01-14 17:04 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-14 17:03 Add HWMON and WiFi support for CU1000-Neo 周琰杰 (Zhou Yanjie)
2020-01-14 17:03 ` [PATCH 0/2] " 周琰杰 (Zhou Yanjie)
2020-01-15 18:59 ` Paul Burton
2020-01-14 17:03 ` 周琰杰 (Zhou Yanjie) [this message]
2020-03-03 13:33 ` [PATCH 1/2] MIPS: Ingenic: Add missing nodes for X1000 and CU1000-Neo Paul Cercueil
2020-01-14 17:03 ` [PATCH 2/2] MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi 周琰杰 (Zhou Yanjie)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1579021428-43535-3-git-send-email-zhouyanjie@wanyeetech.com \
--to=zhouyanjie@wanyeetech.com \
--cc=devicetree@vger.kernel.org \
--cc=ebiederm@xmission.com \
--cc=geert+renesas@glider.be \
--cc=jason@lakedaemon.net \
--cc=jhogan@kernel.org \
--cc=keescook@chromium.org \
--cc=krzk@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=paul.burton@mips.com \
--cc=paul@crapouillou.net \
--cc=paulburton@kernel.org \
--cc=prasannatsmkumar@gmail.com \
--cc=ralf@linux-mips.org \
--cc=rick.tyliu@ingenic.com \
--cc=robh+dt@kernel.org \
--cc=sernia.zhou@foxmail.com \
--cc=syq@debian.org \
--cc=zhenwenjin@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).