From: Harigovindan P <harigovi@codeaurora.org>
To: dri-devel@lists.freedesktop.org, linux-arm-msm@vger.kernel.org,
freedreno@lists.freedesktop.org, devicetree@vger.kernel.org
Cc: Harigovindan P <harigovi@codeaurora.org>,
linux-kernel@vger.kernel.org, robdclark@gmail.com,
seanpaul@chromium.org, hoegsberg@chromium.org,
kalyan_t@codeaurora.org, nganji@codeaurora.org
Subject: [v2] arm64: dts: sc7180: add display dt nodes
Date: Thu, 23 Jan 2020 19:31:38 +0530 [thread overview]
Message-ID: <1579788098-22565-1-git-send-email-harigovi@codeaurora.org> (raw)
Add display, DSI hardware DT nodes for sc7180.
Changes in v1:
-Added display DT nodes for sc7180
Changes in v2:
-Renamed node names
-Corrected code alignments
-Removed extra new line
-Added DISP AHB clock for register access
under display_subsystem node for global settings
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 57 +++++++++++++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 125 ++++++++++++++++++++++++++++++++
2 files changed, 182 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 388f50a..f410614 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -232,6 +232,50 @@
};
};
+&dsi_controller {
+ status = "okay";
+
+ vdda-supply = <&vreg_l3c_1p2>;
+
+ panel@0 {
+ compatible = "visionox,rm69299-1080p-display";
+ reg = <0>;
+
+ vdda-supply = <&vreg_l8c_1p8>;
+ vdd3p3-supply = <&vreg_l18a_2p8>;
+
+ pinctrl-names = "default", "suspend";
+ pinctrl-0 = <&disp_pins_default>;
+ pinctrl-1 = <&disp_pins_default>;
+
+ reset-gpios = <&pm6150l_gpio 3 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ panel0_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel0_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+};
+
+&dsi_phy {
+ status = "okay";
+};
+
&qspi {
status = "okay";
pinctrl-names = "default";
@@ -289,6 +333,19 @@
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
+&pm6150l_gpio {
+ disp_pins {
+ disp_pins_default: disp_pins_default{
+ pins = "gpio3";
+ function = "func1";
+ qcom,drive-strength = <2>;
+ power-source = <0>;
+ bias-disable;
+ output-low;
+ };
+ };
+};
+
&qspi_clk {
pinconf {
pins = "gpio63";
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 3bc3f64..81c3aab 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -1184,6 +1184,131 @@
#power-domain-cells = <1>;
};
+ display_subsystem: mdss@ae00000 {
+ compatible = "qcom,sc7180-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "gcc_bus", "ahb", "core";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ assigned-clock-rates = <300000000>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x800 0x2>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ display_controller: mdp@ae00000 {
+ compatible = "qcom,sc7180-dpu";
+ reg = <0 0x0ae00000 0 0x1000>,
+ <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>,
+ <0 0x0af03000 0 0x16>;
+ reg-names = "mdss", "mdp", "vbif", "disp_cc";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_ROT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "iface", "rot", "lut", "core",
+ "vsync";
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <300000000>,
+ <19200000>;
+
+ interrupt-parent = <&display_subsystem>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi_controller: qcom,mdss_dsi_ctrl0@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&display_subsystem>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ phys = <&dsi_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy: dsi-phy0@ae94400 {
+ compatible = "qcom,dsi-phy-10nm";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94a00 0 0x1e0>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "iface";
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sc7180-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>;
--
2.7.4
next reply other threads:[~2020-01-23 14:02 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-23 14:01 Harigovindan P [this message]
-- strict thread matches above, loose matches on Subject: below --
2020-01-23 12:15 [v2] arm64: dts: sc7180: add display dt nodes Harigovindan P
2020-01-23 18:41 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1579788098-22565-1-git-send-email-harigovi@codeaurora.org \
--to=harigovi@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=freedreno@lists.freedesktop.org \
--cc=hoegsberg@chromium.org \
--cc=kalyan_t@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nganji@codeaurora.org \
--cc=robdclark@gmail.com \
--cc=seanpaul@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).