From: Esben Haabendal <esben@geanix.com>
To: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, "Andrew Lunn" <andrew@lunn.ch>,
"David S . Miller" <davem@davemloft.net>,
"Michal Simek" <michal.simek@xilinx.com>,
"Petr Štetiar" <ynezz@true.cz>
Subject: [PATCH 8/8] net: ll_temac: Add ethtool support for coalesce parameters
Date: Tue, 18 Feb 2020 09:27:41 +0100 [thread overview]
Message-ID: <20200218082741.7710-1-esben@geanix.com> (raw)
Please note that the delays are calculated based on typical
parameters. But as TEMAC is an HDL IP, designs may vary, and future
work might be needed to make this calculation configurable.
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
drivers/net/ethernet/xilinx/ll_temac.h | 5 +-
drivers/net/ethernet/xilinx/ll_temac_main.c | 102 ++++++++++++++++----
2 files changed, 85 insertions(+), 22 deletions(-)
diff --git a/drivers/net/ethernet/xilinx/ll_temac.h b/drivers/net/ethernet/xilinx/ll_temac.h
index 8777ec6e21c8..4a73127e10a6 100644
--- a/drivers/net/ethernet/xilinx/ll_temac.h
+++ b/drivers/net/ethernet/xilinx/ll_temac.h
@@ -379,9 +379,10 @@ struct temac_local {
int rx_bd_tail;
/* DMA channel control setup */
- u32 tx_chnl_ctrl;
- u32 rx_chnl_ctrl;
+ u8 coalesce_count_tx;
+ u8 coalesce_delay_tx;
u8 coalesce_count_rx;
+ u8 coalesce_delay_rx;
struct delayed_work restart_work;
};
diff --git a/drivers/net/ethernet/xilinx/ll_temac_main.c b/drivers/net/ethernet/xilinx/ll_temac_main.c
index e3d4857334f3..3168dd77ecbc 100644
--- a/drivers/net/ethernet/xilinx/ll_temac_main.c
+++ b/drivers/net/ethernet/xilinx/ll_temac_main.c
@@ -379,11 +379,13 @@ static int temac_dma_bd_init(struct net_device *ndev)
}
/* Configure DMA channel (irq setup) */
- lp->dma_out(lp, TX_CHNL_CTRL, lp->tx_chnl_ctrl |
+ lp->dma_out(lp, TX_CHNL_CTRL,
+ lp->coalesce_delay_tx << 24 | lp->coalesce_count_tx << 16 |
0x00000400 | // Use 1 Bit Wide Counters. Currently Not Used!
CHNL_CTRL_IRQ_EN | CHNL_CTRL_IRQ_ERR_EN |
CHNL_CTRL_IRQ_DLY_EN | CHNL_CTRL_IRQ_COAL_EN);
- lp->dma_out(lp, RX_CHNL_CTRL, lp->rx_chnl_ctrl |
+ lp->dma_out(lp, RX_CHNL_CTRL,
+ lp->coalesce_delay_rx << 24 | lp->coalesce_count_rx << 16 |
CHNL_CTRL_IRQ_IOE |
CHNL_CTRL_IRQ_EN | CHNL_CTRL_IRQ_ERR_EN |
CHNL_CTRL_IRQ_DLY_EN | CHNL_CTRL_IRQ_COAL_EN);
@@ -1284,6 +1286,69 @@ static int ll_temac_ethtools_set_ringparam(struct net_device *ndev,
return 0;
}
+static int ll_temac_ethtools_get_coalesce(struct net_device *ndev,
+ struct ethtool_coalesce *ec)
+{
+ struct temac_local *lp = netdev_priv(ndev);
+
+ ec->rx_max_coalesced_frames = lp->coalesce_count_rx;
+ ec->tx_max_coalesced_frames = lp->coalesce_count_tx;
+ ec->rx_coalesce_usecs = (lp->coalesce_delay_rx * 512) / 100;
+ ec->tx_coalesce_usecs = (lp->coalesce_delay_tx * 512) / 100;
+ return 0;
+}
+
+static int ll_temac_ethtools_set_coalesce(struct net_device *ndev,
+ struct ethtool_coalesce *ec)
+{
+ struct temac_local *lp = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ netdev_err(ndev,
+ "Please stop netif before applying configuration\n");
+ return -EFAULT;
+ }
+
+ if (ec->rx_coalesce_usecs_irq ||
+ ec->rx_max_coalesced_frames_irq ||
+ ec->tx_coalesce_usecs_irq ||
+ ec->tx_max_coalesced_frames_irq ||
+ ec->stats_block_coalesce_usecs ||
+ ec->use_adaptive_rx_coalesce ||
+ ec->use_adaptive_tx_coalesce ||
+ ec->pkt_rate_low ||
+ ec->rx_coalesce_usecs_low ||
+ ec->rx_max_coalesced_frames_low ||
+ ec->tx_coalesce_usecs_low ||
+ ec->tx_max_coalesced_frames_low ||
+ ec->pkt_rate_high ||
+ ec->rx_coalesce_usecs_high ||
+ ec->rx_max_coalesced_frames_high ||
+ ec->tx_coalesce_usecs_high ||
+ ec->tx_max_coalesced_frames_high ||
+ ec->rate_sample_interval)
+ return -EOPNOTSUPP;
+ if (ec->rx_max_coalesced_frames)
+ lp->coalesce_count_rx = ec->rx_max_coalesced_frames;
+ if (ec->tx_max_coalesced_frames)
+ lp->coalesce_count_tx = ec->tx_max_coalesced_frames;
+ /* With typical LocalLink clock speed of 200 MHz and
+ * C_PRESCALAR=1023, each delay count corresponds to 5.12 us.
+ */
+ if (ec->rx_coalesce_usecs)
+ lp->coalesce_delay_rx =
+ min(255U, (ec->rx_coalesce_usecs * 100) / 512);
+ if (ec->tx_coalesce_usecs)
+ lp->coalesce_delay_tx =
+ min(255U, (ec->tx_coalesce_usecs * 100) / 512);
+
+ pr_info("%d -> %d %d -> %d\n",
+ ec->rx_coalesce_usecs, lp->coalesce_delay_rx,
+ ec->tx_coalesce_usecs, lp->coalesce_delay_tx);
+
+ return 0;
+}
+
static const struct ethtool_ops temac_ethtool_ops = {
.nway_reset = phy_ethtool_nway_reset,
.get_link = ethtool_op_get_link,
@@ -1292,6 +1357,8 @@ static const struct ethtool_ops temac_ethtool_ops = {
.set_link_ksettings = phy_ethtool_set_link_ksettings,
.get_ringparam = ll_temac_ethtools_get_ringparam,
.set_ringparam = ll_temac_ethtools_set_ringparam,
+ .get_coalesce = ll_temac_ethtools_get_coalesce,
+ .set_coalesce = ll_temac_ethtools_set_coalesce,
};
static int temac_probe(struct platform_device *pdev)
@@ -1401,6 +1468,14 @@ static int temac_probe(struct platform_device *pdev)
/* Can checksum TCP/UDP over IPv4. */
ndev->features |= NETIF_F_IP_CSUM;
+ /* Defaults for IRQ delay/coalescing setup. These are
+ * configuration values, so does not belong in device-tree.
+ */
+ lp->coalesce_delay_tx = 0x10;
+ lp->coalesce_count_tx = 0x22;
+ lp->coalesce_delay_rx = 0xff;
+ lp->coalesce_count_rx = 0x07;
+
/* Setup LocalLink DMA */
if (temac_np) {
/* Find the DMA node, map the DMA registers, and
@@ -1439,14 +1514,6 @@ static int temac_probe(struct platform_device *pdev)
lp->rx_irq = irq_of_parse_and_map(dma_np, 0);
lp->tx_irq = irq_of_parse_and_map(dma_np, 1);
- /* Use defaults for IRQ delay/coalescing setup. These
- * are configuration values, so does not belong in
- * device-tree.
- */
- lp->tx_chnl_ctrl = 0x10220000;
- lp->rx_chnl_ctrl = 0xff070000;
- lp->coalesce_count_rx = 0x07;
-
/* Finished with the DMA node; drop the reference */
of_node_put(dma_np);
} else if (pdata) {
@@ -1472,18 +1539,13 @@ static int temac_probe(struct platform_device *pdev)
lp->tx_irq = platform_get_irq(pdev, 1);
/* IRQ delay/coalescing setup */
- if (pdata->tx_irq_timeout || pdata->tx_irq_count)
- lp->tx_chnl_ctrl = (pdata->tx_irq_timeout << 24) |
- (pdata->tx_irq_count << 16);
- else
- lp->tx_chnl_ctrl = 0x10220000;
+ if (pdata->tx_irq_timeout || pdata->tx_irq_count) {
+ lp->coalesce_delay_tx = pdata->tx_irq_timeout;
+ lp->coalesce_count_tx = pdata->tx_irq_count;
+ }
if (pdata->rx_irq_timeout || pdata->rx_irq_count) {
- lp->rx_chnl_ctrl = (pdata->rx_irq_timeout << 24) |
- (pdata->rx_irq_count << 16);
+ lp->coalesce_delay_rx = pdata->rx_irq_timeout;
lp->coalesce_count_rx = pdata->rx_irq_count;
- } else {
- lp->rx_chnl_ctrl = 0xff070000;
- lp->coalesce_count_rx = 0x07;
}
}
--
2.25.0
next reply other threads:[~2020-02-18 8:27 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-18 8:27 Esben Haabendal [this message]
2020-02-18 13:39 ` [PATCH 8/8] net: ll_temac: Add ethtool support for coalesce parameters Andrew Lunn
2020-02-18 14:28 ` Esben Haabendal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200218082741.7710-1-esben@geanix.com \
--to=esben@geanix.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=michal.simek@xilinx.com \
--cc=netdev@vger.kernel.org \
--cc=ynezz@true.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).