linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ondrej Jirman <megous@megous.com>
To: linux-sunxi@googlegroups.com, Rob Herring <robh+dt@kernel.org>,
	Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>
Cc: Ondrej Jirman <megous@megous.com>,
	Mark Rutland <mark.rutland@arm.com>,
	Corentin Labbe <clabbe@baylibre.com>,
	Georgii Staroselskii <georgii.staroselskii@emlid.com>,
	Samuel Holland <samuel@sholland.org>,
	Martijn Braam <martijn@brixit.nl>, Luca Weiss <luca@z3ntu.xyz>,
	Bhushan Shah <bshah@kde.org>, Icenowy Zheng <icenowy@aosc.io>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v2 3/3] arm64: dts: allwinner: Add initial support for Pine64 PinePhone
Date: Thu, 27 Feb 2020 02:26:50 +0100	[thread overview]
Message-ID: <20200227012650.1179151-4-megous@megous.com> (raw)
In-Reply-To: <20200227012650.1179151-1-megous@megous.com>

At the moment PinePhone comes in two slightly incompatible variants:

- 1.0: Early Developer Batch
- 1.1: Braveheart Batch

There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.

The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.

This is a basic DT that includes only features that are already
supported by mainline drivers.

Co-developed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   2 +
 .../allwinner/sun50i-a64-pinephone-1.0.dts    |  11 +
 .../allwinner/sun50i-a64-pinephone-1.1.dts    |  11 +
 .../dts/allwinner/sun50i-a64-pinephone.dtsi   | 379 ++++++++++++++++++
 4 files changed, 403 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 6dad63881cd3a..e4d3cd0ac5bb7 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -9,6 +9,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
new file mode 100644
index 0000000000000..0c42272106afa
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Ondrej Jirman <megous@megous.com>
+
+/dts-v1/;
+
+#include "sun50i-a64-pinephone.dtsi"
+
+/ {
+	model = "Pine64 PinePhone Developer Batch (1.0)";
+	compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
new file mode 100644
index 0000000000000..06a775c41664b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Ondrej Jirman <megous@megous.com>
+
+/dts-v1/;
+
+#include "sun50i-a64-pinephone.dtsi"
+
+/ {
+	model = "Pine64 PinePhone Braveheart (1.1)";
+	compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
new file mode 100644
index 0000000000000..cefda145c3c9d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
+// Copyright (C) 2020 Martijn Braam <martijn@brixit.nl>
+// Copyright (C) 2020 Ondrej Jirman <megous@megous.com>
+
+#include "sun50i-a64.dtsi"
+#include "sun50i-a64-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+		};
+
+		green {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+		};
+
+		red {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+		};
+	};
+
+	speaker_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
+		vcc-supply = <&reg_dcdc1>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	cpvdd-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&dai {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* Magnetometer */
+	lis3mdl@1e {
+		compatible = "st,lis3mdl-magn";
+		reg = <0x1e>;
+		vdd-supply = <&reg_dldo1>;
+		vddio-supply = <&reg_dldo1>;
+	};
+
+	/* Accelerometer/gyroscope */
+	mpu6050@68 {
+		compatible = "invensense,mpu6050";
+		reg = <0x68>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */
+		vdd-supply = <&reg_dldo1>;
+		vddio-supply = <&reg_dldo1>;
+	};
+};
+
+/* Connected to pogo pins (external spring based pinheader for user addons) */
+&i2c2 {
+	status = "okay";
+};
+
+&lradc {
+	vref-supply = <&reg_aldo3>;
+	status = "okay";
+
+	button-200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_dcdc1>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pe-supply = <&reg_aldo1>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_dldo4>;
+	vcc-ph-supply = <&reg_dcdc1>;
+};
+
+&r_pio {
+	/*
+	 * FIXME: We can't add that supply for now since it would
+	 * create a circular dependency between pinctrl, the regulator
+	 * and the RSB Bus.
+	 *
+	 * vcc-pl-supply = <&reg_aldo2>;
+	 */
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dovdd-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-dsi-sensor";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-mipi-io";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-lpddr";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-lcd-ctp-stk";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1v8-typec";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&sound {
+	status = "okay";
+	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+	simple-audio-card,widgets = "Microphone", "Headset Microphone",
+				    "Microphone", "Internal Microphone",
+				    "Headphone", "Headphone Jack",
+				    "Speaker", "Internal Earpiece",
+				    "Speaker", "Internal Speaker";
+	simple-audio-card,routing =
+			"Headphone Jack", "HP",
+			"Internal Earpiece", "EARPIECE",
+			"Internal Speaker", "Speaker Amp OUTL",
+			"Internal Speaker", "Speaker Amp OUTR",
+			"Speaker Amp INL", "LINEOUT",
+			"Speaker Amp INR", "LINEOUT",
+			"Left DAC", "AIF1 Slot 0 Left",
+			"Right DAC", "AIF1 Slot 0 Right",
+			"AIF1 Slot 0 Left ADC", "Left ADC",
+			"AIF1 Slot 0 Right ADC", "Right ADC",
+			"Internal Microphone", "MBIAS",
+			"MIC1", "Internal Microphone",
+			"Headset Microphone", "HBIAS",
+			"MIC2", "Headset Microphone";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+/* Connected to the modem (hardware flow control can't be used) */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
2.25.1


  parent reply	other threads:[~2020-02-27  1:27 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-27  1:26 [PATCH v2 0/3] Add support for Pine64 PinePhone Linux Smartphone Ondrej Jirman
2020-02-27  1:26 ` [PATCH v2 1/3] arm64: dts: sun50i-a64: Add i2c2 pins Ondrej Jirman
2020-02-27  1:26 ` [PATCH v2 2/3] dt-bindings: arm: sunxi: Add PinePhone 1.0 and 1.1 bindings Ondrej Jirman
2020-02-27  1:32   ` Ondřej Jirman
2020-02-27  1:26 ` Ondrej Jirman [this message]
2020-02-27 13:04 ` [PATCH v2 0/3] Add support for Pine64 PinePhone Linux Smartphone Maxime Ripard
2020-02-27 15:52   ` Ondřej Jirman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200227012650.1179151-4-megous@megous.com \
    --to=megous@megous.com \
    --cc=bshah@kde.org \
    --cc=clabbe@baylibre.com \
    --cc=devicetree@vger.kernel.org \
    --cc=georgii.staroselskii@emlid.com \
    --cc=icenowy@aosc.io \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=luca@z3ntu.xyz \
    --cc=mark.rutland@arm.com \
    --cc=martijn@brixit.nl \
    --cc=mripard@kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=samuel@sholland.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).