From: Heiko Stuebner <heiko@sntech.de>
To: gregkh@linuxfoundation.org
Cc: jslaby@suse.com, andriy.shevchenko@linux.intel.com,
matwey.kornilov@gmail.com, linux-serial@vger.kernel.org,
linux-kernel@vger.kernel.org, heiko@sntech.de,
Giulio Benetti <giulio.benetti@micronovasrl.com>,
Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Subject: [PATCH 3/7] serial: 8250: Handle case port doesn't have TEMT interrupt using em485.
Date: Wed, 18 Mar 2020 15:26:36 +0100 [thread overview]
Message-ID: <20200318142640.982763-4-heiko@sntech.de> (raw)
In-Reply-To: <20200318142640.982763-1-heiko@sntech.de>
From: Giulio Benetti <giulio.benetti@micronovasrl.com>
Some 8250 ports only have TEMT interrupt, so current implementation
can't work for ports without it. The only chance to make it work is to
loop-read on LSR register.
With NO TEMT interrupt check if both TEMT and THRE are set looping on
LSR register.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
drivers/tty/serial/8250/8250.h | 2 +-
drivers/tty/serial/8250/8250_of.c | 2 +-
drivers/tty/serial/8250/8250_omap.c | 2 +-
drivers/tty/serial/8250/8250_port.c | 30 +++++++++++++++++++++--------
include/linux/serial_8250.h | 1 +
5 files changed, 26 insertions(+), 11 deletions(-)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 50a4c174410d..9e049d2a039e 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -190,7 +190,7 @@ void serial8250_rpm_put(struct uart_8250_port *p);
void serial8250_rpm_get_tx(struct uart_8250_port *p);
void serial8250_rpm_put_tx(struct uart_8250_port *p);
-int serial8250_em485_init(struct uart_8250_port *p);
+int serial8250_em485_init(struct uart_8250_port *p, bool has_temt_isr);
void serial8250_em485_destroy(struct uart_8250_port *p);
/* MCR <-> TIOCM conversion */
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index 92fbf46ce3bd..c77ab44a5468 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -64,7 +64,7 @@ static int of_8250_rs485_config(struct uart_port *port,
* are idempotent
*/
if (rs485->flags & SER_RS485_ENABLED) {
- int ret = serial8250_em485_init(up);
+ int ret = serial8250_em485_init(up, true);
if (ret) {
rs485->flags &= ~SER_RS485_ENABLED;
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 836e736ae188..241322900298 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -734,7 +734,7 @@ static int omap_8250_rs485_config(struct uart_port *port,
* are idempotent
*/
if (rs485->flags & SER_RS485_ENABLED) {
- int ret = serial8250_em485_init(up);
+ int ret = serial8250_em485_init(up, true);
if (ret) {
rs485->flags &= ~SER_RS485_ENABLED;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 67aa3a2a9afa..3d1d8490bc42 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -605,15 +605,17 @@ EXPORT_SYMBOL_GPL(serial8250_rpm_put);
/**
* serial8250_em485_init() - put uart_8250_port into rs485 emulating
* @p: uart_8250_port port instance
+ * @p: bool specify if 8250 port has TEMT interrupt or not
*
* The function is used to start rs485 software emulating on the
* &struct uart_8250_port* @p. Namely, RTS is switched before/after
* transmission. The function is idempotent, so it is safe to call it
* multiple times.
*
- * The caller MUST enable interrupt on empty shift register before
- * calling serial8250_em485_init(). This interrupt is not a part of
- * 8250 standard, but implementation defined.
+ * If has_temt_isr is passed as true, the caller MUST enable interrupt
+ * on empty shift register before calling serial8250_em485_init().
+ * This interrupt is not a part of 8250 standard, but implementation
+ * defined.
*
* The function is supposed to be called from .rs485_config callback
* or from any other callback protected with p->port.lock spinlock.
@@ -622,7 +624,7 @@ EXPORT_SYMBOL_GPL(serial8250_rpm_put);
*
* Return 0 - success, -errno - otherwise
*/
-int serial8250_em485_init(struct uart_8250_port *p)
+int serial8250_em485_init(struct uart_8250_port *p, bool has_temt_isr)
{
if (p->em485)
return 0;
@@ -639,6 +641,7 @@ int serial8250_em485_init(struct uart_8250_port *p)
p->em485->start_tx_timer.function = &serial8250_em485_handle_start_tx;
p->em485->port = p;
p->em485->active_timer = NULL;
+ p->em485->has_temt_isr = has_temt_isr;
serial8250_em485_rts_after_send(p);
return 0;
@@ -1475,11 +1478,22 @@ static inline void __stop_tx(struct uart_8250_port *p)
/*
* To provide required timeing and allow FIFO transfer,
* __stop_tx_rs485() must be called only when both FIFO and
- * shift register are empty. It is for device driver to enable
- * interrupt on TEMT.
+ * shift register are empty. If 8250 port supports it,
+ * it is for device driver to enable interrupt on TEMT.
+ * Otherwise must loop-read until TEMT and THRE flags are set.
*/
- if ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
- return;
+ if (em485->has_temt_isr) {
+ if ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
+ return;
+ } else {
+ int val;
+
+ if (serial_in_poll_timeout(p, UART_LSR, val,
+ (val & BOTH_EMPTY) != BOTH_EMPTY,
+ 100000) < 0)
+ pr_warn("%s: timeout waiting for fifos to empty\n",
+ p->port.name);
+ }
em485->active_timer = NULL;
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index bb2bc99388ca..c4b4469c272b 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -79,6 +79,7 @@ struct uart_8250_em485 {
struct hrtimer start_tx_timer; /* "rs485 start tx" timer */
struct hrtimer stop_tx_timer; /* "rs485 stop tx" timer */
struct hrtimer *active_timer; /* pointer to active timer */
+ bool has_temt_isr; /* variant has TEMT interrupt */
struct uart_8250_port *port; /* for hrtimer callbacks */
};
--
2.24.1
next prev parent reply other threads:[~2020-03-18 14:27 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-18 14:26 [PATCH 0/7] serial: 8250: Add rs485 emulation to 8250_dw Heiko Stuebner
2020-03-18 14:26 ` [PATCH 1/7] serial: 8250: Make em485_rts_after_send() set mctrl according to rts state Heiko Stuebner
2020-03-18 14:26 ` [PATCH 2/7] serial: 8250: add serial_in_poll_timeout helper Heiko Stuebner
2020-03-18 15:09 ` Andy Shevchenko
2020-03-18 14:26 ` Heiko Stuebner [this message]
2020-03-18 14:26 ` [PATCH 4/7] serial: 8250: Start rs485 after registering port if rs485 is enabled in probe Heiko Stuebner
2020-03-18 14:26 ` [PATCH 5/7] serial: 8250: handle DTR in rs485 emulation Heiko Stuebner
2020-03-18 14:26 ` [PATCH 6/7] serial: 8250_dw: add em485 support Heiko Stuebner
2020-03-18 15:15 ` Andy Shevchenko
2020-03-18 14:26 ` [PATCH 7/7] serial: 8250_dw: allow enable rs485 at boot time Heiko Stuebner
2020-03-18 15:16 ` Andy Shevchenko
2020-03-18 18:28 ` Heiko Stübner
2020-03-18 18:31 ` Heiko Stübner
2020-03-18 14:43 ` [PATCH 0/7] serial: 8250: Add rs485 emulation to 8250_dw Andy Shevchenko
2020-03-18 15:37 ` Lukas Wunner
2020-03-18 15:54 ` Andy Shevchenko
2020-03-18 18:49 ` Heiko Stübner
2020-03-19 5:40 ` Lukas Wunner
2020-03-23 8:25 ` Heiko Stübner
2020-03-23 13:17 ` Lukas Wunner
2020-03-23 13:41 ` Andy Shevchenko
2020-03-25 13:41 ` Heiko Stübner
2020-03-25 14:42 ` Andy Shevchenko
2020-03-18 15:13 ` Andy Shevchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200318142640.982763-4-heiko@sntech.de \
--to=heiko@sntech.de \
--cc=andriy.shevchenko@linux.intel.com \
--cc=giulio.benetti@micronovasrl.com \
--cc=gregkh@linuxfoundation.org \
--cc=heiko.stuebner@theobroma-systems.com \
--cc=jslaby@suse.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=matwey.kornilov@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).