From: Ansuel Smith <ansuelsmth@gmail.com>
To: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Sham Muthayyan <smuthayy@codeaurora.org>,
Ansuel Smith <ansuelsmth@gmail.com>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Bjorn Helgaas <bhelgaas@google.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
Andrew Murray <amurray@thegoodpenguin.co.uk>,
Philipp Zabel <p.zabel@pengutronix.de>,
linux-arm-msm@vger.kernel.org, linux-pci@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 07/12] pcie: qcom: add tx term offset support
Date: Fri, 20 Mar 2020 19:34:49 +0100 [thread overview]
Message-ID: <20200320183455.21311-7-ansuelsmth@gmail.com> (raw)
In-Reply-To: <20200320183455.21311-1-ansuelsmth@gmail.com>
From: Sham Muthayyan <smuthayy@codeaurora.org>
Add tx term offset support to pcie qcom driver
need in some revision of the ipq806x soc
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
drivers/pci/controller/dwc/pcie-qcom.c | 61 ++++++++++++++++++++++----
1 file changed, 52 insertions(+), 9 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index ecc22fd27ea6..8009e3117765 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -45,7 +45,13 @@
#define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10
#define PCIE20_PARF_PHY_CTRL 0x40
+#define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK (0x1f << 16)
+#define PHY_CTRL_PHY_TX0_TERM_OFFSET(x) (x << 16)
+
#define PCIE20_PARF_PHY_REFCLK 0x4C
+#define REF_SSP_EN BIT(16)
+#define REF_USE_PAD BIT(12)
+
#define PCIE20_PARF_DBI_BASE_ADDR 0x168
#define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16C
#define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174
@@ -77,6 +83,18 @@
#define DBI_RO_WR_EN 1
#define PERST_DELAY_US 1000
+/* PARF registers */
+#define PCIE20_PARF_PCS_DEEMPH 0x34
+#define PCS_DEEMPH_TX_DEEMPH_GEN1(x) (x << 16)
+#define PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(x) (x << 8)
+#define PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(x) (x << 0)
+
+#define PCIE20_PARF_PCS_SWING 0x38
+#define PCS_SWING_TX_SWING_FULL(x) (x << 8)
+#define PCS_SWING_TX_SWING_LOW(x) (x << 0)
+
+#define PCIE20_PARF_CONFIG_BITS 0x50
+#define PHY_RX0_EQ(x) (x << 24)
#define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358
#define SLV_ADDR_SPACE_SZ 0x10000000
@@ -97,6 +115,7 @@ struct qcom_pcie_resources_2_1_0 {
struct reset_control *phy_reset;
struct reset_control *ext_reset;
struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY];
+ uint8_t phy_tx0_term_offset;
};
struct qcom_pcie_resources_1_0_0 {
@@ -184,6 +203,16 @@ struct qcom_pcie {
#define to_qcom_pcie(x) dev_get_drvdata((x)->dev)
+static inline void
+writel_masked(void __iomem *addr, u32 clear_mask, u32 set_mask)
+{
+ u32 val = readl(addr);
+
+ val &= ~clear_mask;
+ val |= set_mask;
+ writel(val, addr);
+}
+
static void qcom_ep_reset_assert(struct qcom_pcie *pcie)
{
gpiod_set_value_cansleep(pcie->reset, 1);
@@ -277,6 +306,10 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
if (IS_ERR(res->ext_reset))
return PTR_ERR(res->ext_reset);
+ if (of_property_read_u8(dev->of_node, "phy-tx0-term-offset",
+ &res->phy_tx0_term_offset))
+ res->phy_tx0_term_offset = 0;
+
res->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
return PTR_ERR_OR_ZERO(res->phy_reset);
}
@@ -304,7 +337,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
struct dw_pcie *pci = pcie->pci;
struct device *dev = pci->dev;
- u32 val;
int ret;
ret = reset_control_assert(res->ahb_reset);
@@ -355,15 +387,26 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
goto err_deassert_ahb;
}
- /* enable PCIe clocks and resets */
- val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
- val &= ~BIT(0);
- writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+ writel_masked(pcie->parf + PCIE20_PARF_PHY_CTRL, BIT(0), 0);
+
+ /* Set Tx termination offset */
+ writel_masked(pcie->parf + PCIE20_PARF_PHY_CTRL,
+ PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK,
+ PHY_CTRL_PHY_TX0_TERM_OFFSET(res->phy_tx0_term_offset));
+
+ /* PARF programming */
+ writel(PCS_DEEMPH_TX_DEEMPH_GEN1(0x18) |
+ PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(0x18) |
+ PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(0x22),
+ pcie->parf + PCIE20_PARF_PCS_DEEMPH);
+ writel(PCS_SWING_TX_SWING_FULL(0x78) |
+ PCS_SWING_TX_SWING_LOW(0x78),
+ pcie->parf + PCIE20_PARF_PCS_SWING);
+ writel(PHY_RX0_EQ(0x4), pcie->parf + PCIE20_PARF_CONFIG_BITS);
- /* enable external reference clock */
- val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK);
- val |= BIT(16);
- writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK);
+ /* Enable reference clock */
+ writel_masked(pcie->parf + PCIE20_PARF_PHY_REFCLK,
+ REF_USE_PAD, REF_SSP_EN);
ret = reset_control_deassert(res->phy_reset);
if (ret) {
--
2.25.1
next prev parent reply other threads:[~2020-03-20 18:35 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-20 18:34 [PATCH 01/12] pcie: qcom: add missing ipq806x clocks in pcie driver Ansuel Smith
2020-03-20 18:34 ` [PATCH 02/12] devicetree: bindings: pci: add missing clks to qcom,pcie Ansuel Smith
2020-03-31 17:30 ` Rob Herring
2020-03-20 18:34 ` [PATCH 03/12] pcie: qcom: change duplicate pci reset to phy reset Ansuel Smith
2020-03-20 18:34 ` [PATCH 04/12] pcie: qcom: Fixed pcie_phy_clk branch issue Ansuel Smith
2020-03-20 18:34 ` [PATCH 05/12] pcie: qcom: add missing reset for ipq806x Ansuel Smith
2020-03-20 18:51 ` Bjorn Helgaas
2020-03-23 6:06 ` Philipp Zabel
2020-03-20 18:34 ` [PATCH 06/12] devicetree: bindings: pci: add ext reset to qcom,pcie Ansuel Smith
2020-03-31 17:31 ` Rob Herring
2020-03-20 18:34 ` Ansuel Smith [this message]
2020-03-20 19:22 ` [PATCH 07/12] pcie: qcom: add tx term offset support Bjorn Helgaas
2020-04-01 20:40 ` Bjorn Andersson
2020-04-01 21:55 ` R: " ansuelsmth
2020-04-01 23:52 ` Bjorn Andersson
2020-03-20 18:34 ` [PATCH 08/12] devicetree: bindings: pci: add phy-tx0-term-offset to qcom,pcie Ansuel Smith
2020-03-31 17:32 ` Rob Herring
2020-04-01 12:09 ` R: " ansuelsmth
2020-04-01 20:41 ` Bjorn Andersson
2020-03-20 18:34 ` [PATCH 09/12] pcie: qcom: Programming the PCIE iATU for IPQ806x Ansuel Smith
2020-03-20 19:26 ` Bjorn Helgaas
2020-04-01 13:21 ` Stanimir Varbanov
2020-03-20 18:34 ` [PATCH 10/12] pcie: qcom: add Force GEN1 support Ansuel Smith
2020-03-20 19:37 ` Bjorn Helgaas
2020-03-20 18:34 ` [PATCH 11/12] devicetree: bindings: pci: add force_gen1 for qcom,pcie Ansuel Smith
2020-03-31 17:33 ` Rob Herring
2020-04-01 12:09 ` R: " ansuelsmth
2020-04-01 13:17 ` Stanimir Varbanov
2020-03-20 18:34 ` [PATCH 12/12] pcie: qcom: Set PCIE MRRS and MPS to 256B Ansuel Smith
2020-03-20 19:46 ` Bjorn Helgaas
2020-03-20 18:47 ` [PATCH 01/12] pcie: qcom: add missing ipq806x clocks in pcie driver Bjorn Helgaas
2020-04-01 13:01 ` Stanimir Varbanov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200320183455.21311-7-ansuelsmth@gmail.com \
--to=ansuelsmth@gmail.com \
--cc=agross@kernel.org \
--cc=amurray@thegoodpenguin.co.uk \
--cc=bhelgaas@google.com \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=mark.rutland@arm.com \
--cc=p.zabel@pengutronix.de \
--cc=robh+dt@kernel.org \
--cc=smuthayy@codeaurora.org \
--cc=svarbanov@mm-sol.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).