From: <Tudor.Ambarus@microchip.com>
To: <alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>, <Nicolas.Ferre@microchip.com>
Cc: <robh+dt@kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <Codrin.Ciubotariu@microchip.com>,
<Tudor.Ambarus@microchip.com>
Subject: [PATCH 01/16] ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions
Date: Thu, 14 May 2020 05:03:07 +0000 [thread overview]
Message-ID: <20200514050301.147442-2-tudor.ambarus@microchip.com> (raw)
In-Reply-To: <20200514050301.147442-1-tudor.ambarus@microchip.com>
From: Tudor Ambarus <tudor.ambarus@microchip.com>
The sama5d2 SoC has the following IPs: [uart0, uart4], {spi0, spi1}, {i2c0, i2c1}.
Label the flexcom functions in order:
flx0: uart5, spi2, i2c2
flx1: uart6, spi3, i2c3
flx2: uart7, spi4, i2c4
flx3: uart8, spi5, i2c5
flx4: uart9, spi6, i2c6
Some boards respected this scheme, others not. Fix the ones that didn't.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
arch/arm/boot/dts/at91-kizbox3-hs.dts | 4 ++--
arch/arm/boot/dts/at91-kizbox3_common.dtsi | 8 ++++----
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 20 ++++++++++----------
arch/arm/boot/dts/at91-sama5d2_icp.dts | 8 ++++----
arch/arm/boot/dts/at91-sama5d2_xplained.dts | 2 +-
5 files changed, 21 insertions(+), 21 deletions(-)
diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/at91-kizbox3-hs.dts
index 8734e7f8939e..0da1f0557eaf 100644
--- a/arch/arm/boot/dts/at91-kizbox3-hs.dts
+++ b/arch/arm/boot/dts/at91-kizbox3-hs.dts
@@ -283,7 +283,7 @@
&flx3 {
status = "okay";
- uart6: serial@200 {
+ uart8: serial@200 {
status = "okay";
};
};
@@ -291,7 +291,7 @@
&flx4 {
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
status = "okay";
};
};
diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
index 299e74d23184..d7a6c972bdac 100644
--- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi
+++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
@@ -28,7 +28,7 @@
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
- serial6 = &uart6;
+ serial6 = &uart8;
};
chosen {
@@ -207,7 +207,7 @@
};
};
- pinctrl_flx4_default: flx4_i2c2_default {
+ pinctrl_flx4_default: flx4_i2c6_default {
pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA
<PIN_PD13__FLEXCOM4_IO1>; //CLK
bias-disable;
@@ -324,7 +324,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "disabled";
- uart6: serial@200 {
+ uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x400>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -350,7 +350,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "disabled";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
index b0853bf7901c..d215243fe163 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@@ -21,7 +21,7 @@
serial1 = &uart4; /* mikro BUS 1 */
serial2 = &uart2; /* mikro BUS 2 */
i2c1 = &i2c1;
- i2c2 = &i2c2;
+ i2c2 = &i2c3;
};
chosen {
@@ -125,7 +125,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c3: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -178,7 +178,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "disabled";
- uart7: serial@200 {
+ uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -190,7 +190,7 @@
status = "disabled"; /* Conflict with isc. */
};
- spi2: spi@400 {
+ spi5: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -207,7 +207,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "okay";
- uart6: serial@200 {
+ uart9: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -216,10 +216,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <32>;
- status = "disabled"; /* Conflict with spi3 and i2c3. */
+ status = "disabled"; /* Conflict with spi6 and i2c6. */
};
- spi3: spi@400 {
+ spi6: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -228,10 +228,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
atmel,fifo-size = <16>;
- status = "okay"; /* Conflict with uart6 and i2c3. */
+ status = "okay"; /* Conflict with uart5 and i2c6. */
};
- i2c3: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -243,7 +243,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <16>;
- status = "disabled"; /* Conflict with uart6 and spi3. */
+ status = "disabled"; /* Conflict with uart5 and spi6. */
};
};
diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts
index cc9fa700eafb..1d9556dbbd63 100644
--- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts
@@ -22,7 +22,7 @@
serial0 = &uart0; /* debug uart0 + mikro BUS 1 */
serial1 = &uart1; /* mikro BUS 3 */
serial3 = &uart3; /* mikro BUS 2 */
- serial5 = &uart5; /* flx2 */
+ serial5 = &uart7; /* flx2 */
i2c0 = &i2c0;
i2c1 = &i2c1;
};
@@ -159,7 +159,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "okay";
- uart5: serial@200 {
+ uart7: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -184,7 +184,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "okay";
- spi3: spi@400 {
+ spi5: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -201,7 +201,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index e0c6cff1a312..0666708b05f9 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -377,7 +377,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
--
2.23.0
next prev parent reply other threads:[~2020-05-14 5:03 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-14 5:03 [PATCH 00/16] ARM: dts: at91: sama5d2: Rework Flexcom definitions Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus [this message]
2020-05-14 5:03 ` [PATCH 02/16] ARM: dts: at91: sama5d2: Move flx4 definitions in the SoC dtsi Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 03/16] ARM: dts: at91: sama5d2: Move flx3 " Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 04/16] ARM: dts: at91: sama5d2: Move flx2 " Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 05/16] ARM: dts: at91: sama5d2: Move flx1 " Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 06/16] ARM: dts: at91: sama5d2: Move flx0 " Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 07/16] ARM: dts: at91: sama5d2: Specify the FIFO size for the Flexcom UART Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 09/16] ARM: dts: at91: sama5d2: Add DMA bindings for the flx3 SPI function Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 08/16] ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and UART flx4 functions Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 10/16] ARM: dts: at91: sama5d2: Add DMA bindings for the flx1 I2C function Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 11/16] ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and I2C flx0 functions Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 13/16] ARM: dts: at91: sama5d2: Remove i2s and tcb aliases from SoC dtsi Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 12/16] ARM: dts: at91: sama5d2: Add missing flexcom definitions Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 14/16] ARM: dts: at91: sama5d2_xplained: Add alias for DBGU Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 16/16] ARM: dts: at91: sama5d2_ptc_ek: Add comments to describe the aliases Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 15/16] ARM: dts: at91: sama5d2_xplained: Describe the flx0 I2C function Tudor.Ambarus
2020-05-15 14:51 ` [PATCH 00/16] ARM: dts: at91: sama5d2: Rework Flexcom definitions Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200514050301.147442-2-tudor.ambarus@microchip.com \
--to=tudor.ambarus@microchip.com \
--cc=Codrin.Ciubotariu@microchip.com \
--cc=Ludovic.Desroches@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).