From: Sandeep Maheswaram <sanm@codeaurora.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Boyd <swboyd@chromium.org>,
Doug Anderson <dianders@chromium.org>,
Matthias Kaehlcke <mka@chromium.org>
Cc: linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, Manu Gautam <mgautam@codeaurora.org>,
Sandeep Maheswaram <sanm@codeaurora.org>
Subject: [PATCH v7 4/4] phy: qcom-qmp: Add QMP V3 USB3 PHY support for SC7180
Date: Fri, 15 May 2020 08:09:18 +0530 [thread overview]
Message-ID: <1589510358-3865-5-git-send-email-sanm@codeaurora.org> (raw)
In-Reply-To: <1589510358-3865-1-git-send-email-sanm@codeaurora.org>
Adding QMP v3 USB3 PHY support for SC7180.
Adding only usb phy reset in the list to avoid
reset of DP block.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 38 +++++++++++++++++++++++++++++++++++++
1 file changed, 38 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 5942167..3504931 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -1578,6 +1578,10 @@ static const char * const msm8996_usb3phy_reset_l[] = {
"phy", "common",
};
+static const char * const sc7180_usb3phy_reset_l[] = {
+ "phy",
+};
+
static const char * const sdm845_pciephy_reset_l[] = {
"phy",
};
@@ -1791,6 +1795,37 @@ static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
.is_dual_lane_phy = true,
};
+static const struct qmp_phy_cfg sc7180_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = qmp_v3_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
+ .tx_tbl = qmp_v3_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
+ .rx_tbl = qmp_v3_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
+ .pcs_tbl = qmp_v3_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
+ .clk_list = qmp_v3_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
+ .reset_list = sc7180_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(sc7180_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = qmp_v3_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+
+ .has_phy_dp_com_ctrl = true,
+ .is_dual_lane_phy = true,
+};
+
static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
.type = PHY_TYPE_USB3,
.nlanes = 1,
@@ -2680,6 +2715,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
.compatible = "qcom,ipq8074-qmp-pcie-phy",
.data = &ipq8074_pciephy_cfg,
}, {
+ .compatible = "qcom,sc7180-qmp-usb3-phy",
+ .data = &sc7180_usb3phy_cfg,
+ }, {
.compatible = "qcom,sdm845-qhp-pcie-phy",
.data = &sdm845_qhp_pciephy_cfg,
}, {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2020-05-15 2:40 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-15 2:39 [PATCH v7 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
2020-05-15 2:39 ` [PATCH v7 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
2020-05-15 18:18 ` Matthias Kaehlcke
2020-05-15 2:39 ` [PATCH v7 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY Sandeep Maheswaram
2020-05-15 18:39 ` Matthias Kaehlcke
2020-05-26 21:25 ` Rob Herring
2020-05-15 2:39 ` [PATCH v7 3/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180 Sandeep Maheswaram
2020-05-26 21:25 ` Rob Herring
2020-05-15 2:39 ` Sandeep Maheswaram [this message]
2020-05-19 6:23 ` [PATCH v7 0/4] Add QMP V3 USB3 PHY " Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1589510358-3865-5-git-send-email-sanm@codeaurora.org \
--to=sanm@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mgautam@codeaurora.org \
--cc=mka@chromium.org \
--cc=robh+dt@kernel.org \
--cc=swboyd@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).