From: Drew Fustini <drew@beagleboard.org>
To: "Linus Walleij" <linus.walleij@linaro.org>,
"Grygorii Strashko" <grygorii.strashko@ti.com>,
"Benoît Cousson" <bcousson@baylibre.com>,
"Tony Lindgren" <tony@atomide.com>,
"Rob Herring" <robh+dt@kernel.org>,
Linux-OMAP <linux-omap@vger.kernel.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
"Jason Kridner" <jkridner@beagleboard.org>,
"Robert Nelson" <robertcnelson@beagleboard.org>
Subject: [PATCH v2] arm: dts: am33xx-bone-common: add gpio-line-names
Date: Wed, 20 May 2020 23:47:57 +0200 [thread overview]
Message-ID: <20200520214757.GA362547@x1> (raw)
Add gpio-line-names properties to the GPIO controller nodes.
BeagleBone boards have P8 and P9 headers [0] which expose many of the
AM3358 ZCZ SoC balls to stacking expansion boards called "capes", or to
other external connections like jumper wires connected to a breadboard.
BeagleBone users will often refer to the "Cape Exanpsion Headers" pin
diagram [1] as it is in the "Bone101" getting started tutorial. [2]
Most of the P8 and P9 header pins can muxed to a GPIO line. The
gpio-line-names describe which P8 or P9 pin that line goes to and the
default mux for that P8 or P9 pin if it is not GPIO.
For example, gpiochip 1 line 0 is connected to P8 header pin 25 (P8_25)
however the default device tree has the corresponding BGA ball (ZCZ U7)
muxed to mmc1_dat0 as it is used for the on-board eMMC chip. For that
GPIO line to be used, one would need to modify the device tree to
disable the eMMC and change the pin mux for that ball to GPIO mode.
Some of the AM3358 ZCZ balls corresponding to GPIO lines are not routed
to a P8 or P9 header, but are instead wired to some peripheral device
like on-board eMMC, HDMI framer IC, or status LEDs. Those names are in
brackets to denote those GPIO lines can not be used.
Some GPIO lines are named "[NC]" as the corresponding balls are not
routed to anything on the PCB.
The goal for these names is to make it easier for a user viewing the
output of gpioinfo to determine which P8 or P9 pin is connected to a
GPIO line. The output of gpioinfo on a BeagleBone Black would be:
debian@beaglebone:~$ gpioinfo
gpiochip0 - 32 lines:
line 0: "[ethernet]" unused input active-high
line 1: "[ethernet]" unused input active-high
line 2: "P9_22 [spi0_sclk]" unused input active-high
line 3: "P9_21 [spi0_d0]" unused input active-high
line 4: "P9_18 [spi0_d1]" unused input active-high
line 5: "P9_17 [spi0_cs0]" unused input active-high
line 6: "[sd card]" "cd" input active-low [used]
line 7: "P9_42A [ecappwm0]" unused input active-high
line 8: "P8_35 [hdmi]" unused input active-high
line 9: "P8_33 [hdmi]" unused input active-high
line 10: "P8_31 [hdmi]" unused input active-high
line 11: "P8_32 [hdmi]" unused input active-high
line 12: "P9_20 [i2c2_sda]" unused input active-high
line 13: "P9_19 [i2c2_scl]" unused input active-high
line 14: "P9_26 [uart1_rxd]" unused input active-high
line 15: "P9_24 [uart1_txd]" unused input active-high
line 16: "[ethernet]" unused input active-high
line 17: "[ethernet]" unused input active-high
line 18: "[usb]" unused input active-high
line 19: "[hdmi]" unused input active-high
line 20: "P9_41B" unused input active-high
line 21: "[ethernet]" unused input active-high
line 22: "P8_19 [ehrpwm2a]" unused input active-high
line 23: "P8_13 [ehrpwm2b]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "P8_14" unused input active-high
line 27: "P8_17" unused input active-high
line 28: "[ethernet]" unused input active-high
line 29: "[ethernet]" unused input active-high
line 30: "P9_11 [uart4_rxd]" unused input active-high
line 31: "P9_13 [uart4_txd]" unused input active-high
gpiochip1 - 32 lines:
line 0: "P8_25 [emmc]" unused input active-high
line 1: "[emmc]" unused input active-high
line 2: "P8_5 [emmc]" unused input active-high
line 3: "P8_6 [emmc]" unused input active-high
line 4: "P8_23 [emmc]" unused input active-high
line 5: "P8_22 [emmc]" unused input active-high
line 6: "P8_3 [emmc]" unused input active-high
line 7: "P8_4 [emmc]" unused input active-high
line 8: "[NC]" unused input active-high
line 9: "[NC]" unused input active-high
line 10: "[NC]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "P8_12" unused input active-high
line 13: "P8_11" unused input active-high
line 14: "P8_16" unused input active-high
line 15: "P8_15" unused input active-high
line 16: "P9_15A" unused input active-high
line 17: "P9_23" unused input active-high
line 18: "P9_14 [ehrpwm1a]" unused input active-high
line 19: "P9_16 [ehrpwm1b]" unused input active-high
line 20: "[emmc]" unused input active-high
line 21: "[usr0 led]" "beaglebone:green:heartbeat" output active-high [used]
line 22: "[usr1 led]" "beaglebone:green:mmc0" output active-high [used]
line 23: "[usr2 led]" "beaglebone:green:usr2" output active-high [used]
line 24: "[usr3 led]" "beaglebone:green:usr3" output active-high [used]
line 25: "[hdmi]" "interrupt" input active-high [used]
line 26: "[usb]" unused input active-high
line 27: "[hdmi audio]" "enable" output active-high [used]
line 28: "P9_12" unused input active-high
line 29: "P8_26" unused input active-high
line 30: "P8_21 [emmc]" unused input active-high
line 31: "P8_20 [emmc]" unused input active-high
gpiochip2 - 32 lines:
line 0: "P9_15B" unused input active-high
line 1: "P8_18" unused input active-high
line 2: "P8_7" unused input active-high
line 3: "P8_8" unused input active-high
line 4: "P8_10" unused input active-high
line 5: "P8_9" unused input active-high
line 6: "P8_45 [hdmi]" unused input active-high
line 7: "P8_46 [hdmi]" unused input active-high
line 8: "P8_43 [hdmi]" unused input active-high
line 9: "P8_44 [hdmi]" unused input active-high
line 10: "P8_41 [hdmi]" unused input active-high
line 11: "P8_42 [hdmi]" unused input active-high
line 12: "P8_39 [hdmi]" unused input active-high
line 13: "P8_40 [hdmi]" unused input active-high
line 14: "P8_37 [hdmi]" unused input active-high
line 15: "P8_38 [hdmi]" unused input active-high
line 16: "P8_36 [hdmi]" unused input active-high
line 17: "P8_34 [hdmi]" unused input active-high
line 18: "[ethernet]" unused input active-high
line 19: "[ethernet]" unused input active-high
line 20: "[ethernet]" unused input active-high
line 21: "[ethernet]" unused input active-high
line 22: "P8_27 [hdmi]" unused input active-high
line 23: "P8_29 [hdmi]" unused input active-high
line 24: "P8_28 [hdmi]" unused input active-high
line 25: "P8_30 [hdmi]" unused input active-high
line 26: "[emmc]" unused input active-high
line 27: "[emmc]" unused input active-high
line 28: "[emmc]" unused input active-high
line 29: "[emmc]" unused input active-high
line 30: "[emmc]" unused input active-high
line 31: "[emmc]" unused input active-high
gpiochip3 - 32 lines:
line 0: "[ethernet]" unused input active-high
line 1: "[ethernet]" unused input active-high
line 2: "[ethernet]" unused input active-high
line 3: "[ethernet]" unused input active-high
line 4: "[ethernet]" unused input active-high
line 5: "[i2c0]" unused input active-high
line 6: "[i2c0]" unused input active-high
line 7: "[emu]" unused input active-high
line 8: "[emu]" unused input active-high
line 9: "[ethernet]" unused input active-high
line 10: "[ethernet]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "[NC]" unused input active-high
line 13: "[usb]" unused input active-high
line 14: "P9_31 [spi1_sclk]" unused input active-high
line 15: "P9_29 [spi1_d0]" unused input active-high
line 16: "P9_30 [spi1_d1]" unused input active-high
line 17: "P9_28 [spi1_cs0]" unused input active-high
line 18: "P9_42B [ecappwm0]" unused input active-high
line 19: "P9_27" unused input active-high
line 20: "P9_41A" unused input active-high
line 21: "P9_25" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "[NC]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "[NC]" unused input active-high
line 27: "[NC]" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
[0] https://git.io/JfgOd
[1] https://beagleboard.org/capes
[1] https://beagleboard.org/Support/bone101
[2] https://beagleboard.org/static/images/cape-headers.png
Reviewed-by: Jason Kridner <jason@beagleboard.org>
Reviewed-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
---
arch/arm/boot/dts/am335x-bone-common.dtsi | 144 ++++++++++++++++++++++
1 file changed, 144 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi
index 6c9187bc0f17..d86e67b0e852 100644
--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
+++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
@@ -397,3 +397,147 @@ &rtc {
clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
clock-names = "ext-clk", "int-clk";
};
+
+&gpio0 {
+ gpio-line-names =
+ "[ethernet]",
+ "[ethernet]",
+ "P9_22 [spi0_sclk]",
+ "P9_21 [spi0_d0]",
+ "P9_18 [spi0_d1]",
+ "P9_17 [spi0_cs0]",
+ "[sd card]",
+ "P9_42A [ecappwm0]",
+ "P8_35 [hdmi]",
+ "P8_33 [hdmi]",
+ "P8_31 [hdmi]",
+ "P8_32 [hdmi]",
+ "P9_20 [i2c2_sda]",
+ "P9_19 [i2c2_scl]",
+ "P9_26 [uart1_rxd]",
+ "P9_24 [uart1_txd]",
+ "[ethernet]",
+ "[ethernet]",
+ "[usb]",
+ "[hdmi]",
+ "P9_41B",
+ "[ethernet]",
+ "P8_19 [ehrpwm2a]",
+ "P8_13 [ehrpwm2b]",
+ "[NC]",
+ "[NC]",
+ "P8_14",
+ "P8_17",
+ "[ethernet]",
+ "[ethernet]",
+ "P9_11 [uart4_rxd]",
+ "P9_13 [uart4_txd]";
+};
+
+&gpio1 {
+ gpio-line-names =
+ "P8_25 [emmc]",
+ "[emmc]",
+ "P8_5 [emmc]",
+ "P8_6 [emmc]",
+ "P8_23 [emmc]",
+ "P8_22 [emmc]",
+ "P8_3 [emmc]",
+ "P8_4 [emmc]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "P8_12",
+ "P8_11",
+ "P8_16",
+ "P8_15",
+ "P9_15A",
+ "P9_23",
+ "P9_14 [ehrpwm1a]",
+ "P9_16 [ehrpwm1b]",
+ "[emmc]",
+ "[usr0 led]",
+ "[usr1 led]",
+ "[usr2 led]",
+ "[usr3 led]",
+ "[hdmi]",
+ "[usb]",
+ "[hdmi audio]",
+ "P9_12",
+ "P8_26",
+ "P8_21 [emmc]",
+ "P8_20 [emmc]";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "P9_15B",
+ "P8_18",
+ "P8_7",
+ "P8_8",
+ "P8_10",
+ "P8_9",
+ "P8_45 [hdmi]",
+ "P8_46 [hdmi]",
+ "P8_43 [hdmi]",
+ "P8_44 [hdmi]",
+ "P8_41 [hdmi]",
+ "P8_42 [hdmi]",
+ "P8_39 [hdmi]",
+ "P8_40 [hdmi]",
+ "P8_37 [hdmi]",
+ "P8_38 [hdmi]",
+ "P8_36 [hdmi]",
+ "P8_34 [hdmi]",
+ "[ethernet]",
+ "[ethernet]",
+ "[ethernet]",
+ "[ethernet]",
+ "P8_27 [hdmi]",
+ "P8_29 [hdmi]",
+ "P8_28 [hdmi]",
+ "P8_30 [hdmi]",
+ "[emmc]",
+ "[emmc]",
+ "[emmc]",
+ "[emmc]",
+ "[emmc]",
+ "[emmc]";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "[ethernet]",
+ "[ethernet]",
+ "[ethernet]",
+ "[ethernet]",
+ "[ethernet]",
+ "[i2c0]",
+ "[i2c0]",
+ "[emu]",
+ "[emu]",
+ "[ethernet]",
+ "[ethernet]",
+ "[NC]",
+ "[NC]",
+ "[usb]",
+ "P9_31 [spi1_sclk]",
+ "P9_29 [spi1_d0]",
+ "P9_30 [spi1_d1]",
+ "P9_28 [spi1_cs0]",
+ "P9_42B [ecappwm0]",
+ "P9_27",
+ "P9_41A",
+ "P9_25",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]",
+ "[NC]";
+};
--
2.25.1
next reply other threads:[~2020-05-20 21:48 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-20 21:47 Drew Fustini [this message]
2020-05-21 14:34 ` [PATCH v2] arm: dts: am33xx-bone-common: add gpio-line-names Grygorii Strashko
2020-05-21 14:41 ` Robert Nelson
2020-05-21 17:26 ` Grygorii Strashko
2020-05-21 19:23 ` Drew Fustini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200520214757.GA362547@x1 \
--to=drew@beagleboard.org \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=grygorii.strashko@ti.com \
--cc=jkridner@beagleboard.org \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=robertcnelson@beagleboard.org \
--cc=robh+dt@kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).