[net-next,v1,4/5] net: phy: micrel: ksz8081 add MDI-X support
diff mbox series

Message ID 20200710120851.28984-5-o.rempel@pengutronix.de
State New
Headers show
Series
  • add cable test support for ksz8081 and ksz8873
Related show

Commit Message

Oleksij Rempel July 10, 2020, 12:08 p.m. UTC
Add support for MDI-X status and configuration

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/phy/micrel.c | 89 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 89 insertions(+)

Comments

Andrew Lunn July 10, 2020, 1:50 p.m. UTC | #1
On Fri, Jul 10, 2020 at 02:08:50PM +0200, Oleksij Rempel wrote:
> Add support for MDI-X status and configuration
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Patch
diff mbox series

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index ec409b2cb984..221ba661645f 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -64,11 +64,17 @@ 
 
 /* PHY Control 1 */
 #define MII_KSZPHY_CTRL_1			0x1e
+#define KSZ8081_CTRL1_MDIX_STAT			BIT(4)
 
 /* PHY Control 2 / PHY Control (if no PHY Control 1) */
 #define MII_KSZPHY_CTRL_2			0x1f
 #define MII_KSZPHY_CTRL				MII_KSZPHY_CTRL_2
 /* bitmap of PHY register to set interrupt mode */
+#define KSZ8081_CTRL2_HP_MDIX			BIT(15)
+#define KSZ8081_CTRL2_MDI_MDI_X_SELECT		BIT(14)
+#define KSZ8081_CTRL2_DISABLE_AUTO_MDIX		BIT(13)
+#define KSZ8081_CTRL2_FORCE_LINK		BIT(11)
+#define KSZ8081_CTRL2_POWER_SAVING		BIT(10)
 #define KSZPHY_CTRL_INT_ACTIVE_HIGH		BIT(9)
 #define KSZPHY_RMII_REF_CLK_SEL			BIT(7)
 #define KSZ886X_CTRL_MDIX_STAT			BIT(4)
@@ -398,6 +404,87 @@  static int ksz8081_config_init(struct phy_device *phydev)
 	return kszphy_config_init(phydev);
 }
 
+static int ksz8081_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+	u16 val;
+
+	switch (ctrl) {
+	case ETH_TP_MDI:
+		val = KSZ8081_CTRL2_DISABLE_AUTO_MDIX;
+		break;
+	case ETH_TP_MDI_X:
+		val = KSZ8081_CTRL2_DISABLE_AUTO_MDIX |
+			KSZ8081_CTRL2_MDI_MDI_X_SELECT;
+		break;
+	case ETH_TP_MDI_AUTO:
+		val = 0;
+		break;
+	default:
+		return 0;
+	}
+
+	return phy_modify(phydev, MII_KSZPHY_CTRL_2,
+			  KSZ8081_CTRL2_HP_MDIX |
+			  KSZ8081_CTRL2_MDI_MDI_X_SELECT |
+			  KSZ8081_CTRL2_DISABLE_AUTO_MDIX,
+			  KSZ8081_CTRL2_HP_MDIX | val);
+}
+
+static int ksz8081_config_aneg(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_config_aneg(phydev);
+	if (ret)
+		return ret;
+
+	/* The MDI-X configuration is automatically changed by the PHY after
+	 * switching from autoneg off to on. So, take MDI-X configuration under
+	 * own control and set it after autoneg configuration was done.
+	 */
+	return ksz8081_config_mdix(phydev, phydev->mdix_ctrl);
+}
+
+static int ksz8081_mdix_update(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_read(phydev, MII_KSZPHY_CTRL_2);
+	if (ret < 0)
+		return ret;
+
+	if (ret & KSZ8081_CTRL2_DISABLE_AUTO_MDIX) {
+		if (ret & KSZ8081_CTRL2_MDI_MDI_X_SELECT)
+			phydev->mdix_ctrl = ETH_TP_MDI_X;
+		else
+			phydev->mdix_ctrl = ETH_TP_MDI;
+	} else {
+		phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+	}
+
+	ret = phy_read(phydev, MII_KSZPHY_CTRL_1);
+	if (ret < 0)
+		return ret;
+
+	if (ret & KSZ8081_CTRL1_MDIX_STAT)
+		phydev->mdix = ETH_TP_MDI;
+	else
+		phydev->mdix = ETH_TP_MDI_X;
+
+	return 0;
+}
+
+static int ksz8081_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = ksz8081_mdix_update(phydev);
+	if (ret < 0)
+		return ret;
+
+	return genphy_read_status(phydev);
+}
+
 static int ksz8061_config_init(struct phy_device *phydev)
 {
 	int ret;
@@ -1381,6 +1468,8 @@  static struct phy_driver ksphy_driver[] = {
 	.driver_data	= &ksz8081_type,
 	.probe		= kszphy_probe,
 	.config_init	= ksz8081_config_init,
+	.config_aneg	= ksz8081_config_aneg,
+	.read_status	= ksz8081_read_status,
 	.ack_interrupt	= kszphy_ack_interrupt,
 	.config_intr	= kszphy_config_intr,
 	.get_sset_count = kszphy_get_sset_count,