From: Alain Volmat <alain.volmat@st.com>
To: <broonie@kernel.org>, <amelie.delaunay@st.com>
Cc: <mcoquelin.stm32@gmail.com>, <alexandre.torgue@st.com>,
<linux-spi@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <fabrice.gasnier@st.com>,
<alain.volmat@st.com>
Subject: [PATCH 02/18] spi: stm32-spi: defer probe for reset
Date: Wed, 5 Aug 2020 09:01:57 +0200 [thread overview]
Message-ID: <1596610933-32599-3-git-send-email-alain.volmat@st.com> (raw)
In-Reply-To: <1596610933-32599-1-git-send-email-alain.volmat@st.com>
Defer the probe operation when a reset controller device is expected
but have not yet been probed.
This change replaces use of devm_reset_control_get_exclusive() with
devm_reset_control_get_optional_exclusive() as reset controller is
optional which is now explicitly stated.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
---
drivers/spi/spi-stm32.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/spi/spi-stm32.c b/drivers/spi/spi-stm32.c
index 838d3ce3ebae..eaa416c551c9 100644
--- a/drivers/spi/spi-stm32.c
+++ b/drivers/spi/spi-stm32.c
@@ -1886,8 +1886,16 @@ static int stm32_spi_probe(struct platform_device *pdev)
goto err_clk_disable;
}
- rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
- if (!IS_ERR(rst)) {
+ rst = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
+ if (rst) {
+ if (IS_ERR(rst)) {
+ ret = PTR_ERR(rst);
+ if (ret != -EPROBE_DEFER)
+ dev_err(&pdev->dev, "reset get failed: %d\n",
+ ret);
+ goto err_clk_disable;
+ }
+
reset_control_assert(rst);
udelay(2);
reset_control_deassert(rst);
--
2.7.4
next prev parent reply other threads:[~2020-08-05 7:04 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-05 7:01 [PATCH 00/18] spi: stm32: various driver enhancements Alain Volmat
2020-08-05 7:01 ` [PATCH 01/18] spi: stm32-spi: driver uses reset controller only at init Alain Volmat
2020-08-05 7:01 ` Alain Volmat [this message]
2020-08-05 10:49 ` [PATCH 02/18] spi: stm32-spi: defer probe for reset Mark Brown
2020-08-07 13:42 ` Alain Volmat
2020-08-07 14:01 ` Mark Brown
2020-08-05 7:01 ` [PATCH 03/18] spi: stm32h7: remove unused mode fault MODF event handling Alain Volmat
2020-08-05 10:51 ` Mark Brown
2020-08-05 7:01 ` [PATCH 04/18] spi: stm32: use bitfield macros Alain Volmat
2020-08-05 7:02 ` [PATCH 05/18] spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC Alain Volmat
2020-08-05 7:02 ` [PATCH 06/18] spi: stm32h7: fix irq handler Alain Volmat
2020-08-05 7:02 ` [PATCH 07/18] spi: stm32h7: rework rx fifo read function Alain Volmat
2020-08-05 7:02 ` [PATCH 08/18] spi: stm32h7: fix dbg/warn/err conditions in irq handler Alain Volmat
2020-08-05 7:02 ` [PATCH 09/18] spi: stm32h7: fix race condition at end of transfer Alain Volmat
2020-08-05 10:53 ` Mark Brown
2020-08-05 7:02 ` [PATCH 10/18] spi: stm32: wait for completion in transfer_one() Alain Volmat
2020-08-05 10:58 ` Mark Brown
2020-08-05 7:02 ` [PATCH 11/18] spi: stm32: fix fifo threshold level in case of short transfer Alain Volmat
2020-08-05 10:59 ` Mark Brown
2020-08-05 7:02 ` [PATCH 12/18] spi: stm32: move spi disable out of irq handler Alain Volmat
2020-08-05 11:01 ` Mark Brown
2020-08-05 7:02 ` [PATCH 13/18] spi: stm32h7: fix handling of dma transfer completed Alain Volmat
2020-08-05 11:02 ` Mark Brown
2020-08-05 7:02 ` [PATCH 14/18] spi: stm32: improve suspend/resume management Alain Volmat
2020-08-05 7:02 ` [PATCH 15/18] spi: stm32: fix stm32_spi_prepare_mbr in case of odd clk_rate Alain Volmat
2020-08-05 11:02 ` Mark Brown
2020-08-05 7:02 ` [PATCH 16/18] spi: stm32: always perform registers configuration prior to transfer Alain Volmat
2020-08-05 11:03 ` Mark Brown
2020-08-05 7:02 ` [PATCH 17/18] spi: stm32: properly handle 0 byte transfer Alain Volmat
2020-08-05 7:02 ` [PATCH 18/18] spi: stm32h7: ensure message are smaller than max size Alain Volmat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1596610933-32599-3-git-send-email-alain.volmat@st.com \
--to=alain.volmat@st.com \
--cc=alexandre.torgue@st.com \
--cc=amelie.delaunay@st.com \
--cc=broonie@kernel.org \
--cc=fabrice.gasnier@st.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).