From: Florian Fainelli <f.fainelli@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com,
Florian Fainelli <f.fainelli@gmail.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND
FLATTENED DEVICE TREE BINDINGS)
Subject: [PATCH 2/2] phy: phy-brcm-sata: Allow configuration SATA AFE TX amplitude
Date: Wed, 30 Sep 2020 20:19:16 -0700 [thread overview]
Message-ID: <20201001031916.411999-3-f.fainelli@gmail.com> (raw)
In-Reply-To: <20201001031916.411999-1-f.fainelli@gmail.com>
Read the 'brcm,tx-amplitude-millivolt' property from Device Tree and
propagate its value into the appropriate test transmit register to
change the TX amplitude.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/phy/broadcom/phy-brcm-sata.c | 32 ++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/drivers/phy/broadcom/phy-brcm-sata.c b/drivers/phy/broadcom/phy-brcm-sata.c
index 18251f232172..7be3586b16cb 100644
--- a/drivers/phy/broadcom/phy-brcm-sata.c
+++ b/drivers/phy/broadcom/phy-brcm-sata.c
@@ -65,6 +65,7 @@ struct brcm_sata_port {
bool ssc_en;
enum brcm_sata_phy_rxaeq_mode rxaeq_mode;
u32 rxaeq_val;
+ u32 tx_amplitude_val;
};
struct brcm_sata_phy {
@@ -84,6 +85,10 @@ enum sata_phy_regs {
BLOCK0_SPARE_OOB_CLK_SEL_MASK = 0x3,
BLOCK0_SPARE_OOB_CLK_SEL_REFBY2 = 0x1,
+ BLOCK1_REG_BANK = 0x10,
+ BLOCK1_TEST_TX = 0x83,
+ BLOCK1_TEST_TX_AMP_SHIFT = 12,
+
PLL_REG_BANK_0 = 0x050,
PLL_REG_BANK_0_PLLCONTROL_0 = 0x81,
PLLCONTROL_0_FREQ_DET_RESTART = BIT(13),
@@ -379,6 +384,29 @@ static int brcm_stb_sata_16nm_ssc_init(struct brcm_sata_port *port)
brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1,
~tmp, RXPMD_MON_CORRECT_EN | value);
+ tmp = GENMASK(15, 12);
+ switch (port->tx_amplitude_val) {
+ case 400:
+ value = BIT(12) | BIT(13);
+ break;
+ case 500:
+ value = BIT(13);
+ break;
+ case 600:
+ value = BIT(12);
+ break;
+ case 800:
+ value = 0;
+ break;
+ default:
+ value = tmp;
+ break;
+ }
+
+ if (value != tmp)
+ brcm_sata_phy_wr(port, BLOCK1_REG_BANK, BLOCK1_TEST_TX, ~tmp,
+ value);
+
/* Turn on/off SSC */
brcm_sata_phy_wr(port, TX_REG_BANK, TX_ACTRL5, ~TX_ACTRL5_SSC_EN,
port->ssc_en ? TX_ACTRL5_SSC_EN : 0);
@@ -791,6 +819,10 @@ static int brcm_sata_phy_probe(struct platform_device *pdev)
if (port->rxaeq_mode == RXAEQ_MODE_MANUAL)
of_property_read_u32(child, "brcm,rxaeq-value",
&port->rxaeq_val);
+
+ of_property_read_u32(child, "brcm,tx-amplitude-millivolt",
+ &port->tx_amplitude_val);
+
port->ssc_en = of_property_read_bool(child, "brcm,enable-ssc");
if (IS_ERR(port->phy)) {
dev_err(dev, "failed to create PHY\n");
--
2.25.1
next prev parent reply other threads:[~2020-10-01 3:19 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-01 3:19 [PATCH 0/2] phy: phy-brcm-sata: Allow configuration SATA AFE TX amplitude Florian Fainelli
2020-10-01 3:19 ` [PATCH 1/2] dt-bindings: phy: Allow defining the " Florian Fainelli
2020-10-06 20:21 ` Rob Herring
2020-10-01 3:19 ` Florian Fainelli [this message]
2020-10-05 2:56 ` [PATCH 0/2] phy: phy-brcm-sata: Allow configuration " Florian Fainelli
2020-10-05 5:43 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201001031916.411999-3-f.fainelli@gmail.com \
--to=f.fainelli@gmail.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).