From: Coiby Xu <coiby.xu@gmail.com>
To: linux-gpio@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>,
Hans de Goede <hdegoede@redhat.com>,
linux-kernel@vger.kernel.org (open list)
Subject: [PATCH] pinctrl: amd: print debounce filter info in debugfs
Date: Sat, 24 Oct 2020 14:15:52 +0800 [thread overview]
Message-ID: <20201024061552.4497-1-coiby.xu@gmail.com> (raw)
Print out the status of debounce filter as follows,
$ cat /sys/kernel/debug/gpio|grep pin130
pin130 interrupt is disabled| interrupt is masked| disable wakeup in S0i3 state| disable wakeup in S3 state|
disable wakeup in S4/S5 state| input is high| pull-up is disabled| Pull-down is disabled| output is disabled| debouncing filter (high) enabled| debouncing timeout is 124800 (us)| 0x503c8
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
---
drivers/pinctrl/pinctrl-amd.c | 43 +++++++++++++++++++++++++++++++++--
1 file changed, 41 insertions(+), 2 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c
index 9a760f5cd7ed..9897f86b1bec 100644
--- a/drivers/pinctrl/pinctrl-amd.c
+++ b/drivers/pinctrl/pinctrl-amd.c
@@ -197,10 +197,16 @@ static int amd_gpio_set_config(struct gpio_chip *gc, unsigned offset,
static void amd_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gc)
{
u32 pin_reg;
+ u32 reg_db_mask;
unsigned long flags;
unsigned int bank, i, pin_num;
struct amd_gpio *gpio_dev = gpiochip_get_data(gc);
+ bool tmr_out_unit;
+ unsigned int time;
+ unsigned int unit;
+ bool tmr_large;
+
char *level_trig;
char *active_level;
char *interrupt_enable;
@@ -214,6 +220,8 @@ static void amd_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gc)
char *pull_down_enable;
char *output_value;
char *output_enable;
+ char debounce_value[40];
+ char *debounce_enable;
for (bank = 0; bank < gpio_dev->hwbank_num; bank++) {
seq_printf(s, "GPIO bank%d\t", bank);
@@ -327,13 +335,44 @@ static void amd_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gc)
pin_sts = "input is low|";
}
+ reg_db_mask = (DB_CNTRl_MASK << DB_CNTRL_OFF) & pin_reg;
+ if (reg_db_mask & pin_reg) {
+ tmr_out_unit = pin_reg & BIT(DB_TMR_OUT_UNIT_OFF);
+ tmr_large = pin_reg & BIT(DB_TMR_LARGE_OFF);
+ time = pin_reg & DB_TMR_OUT_MASK;
+ if (!tmr_large) {
+ if (!tmr_out_unit)
+ unit = 61;
+ else
+ unit = 244;
+ } else {
+ if (!tmr_out_unit)
+ unit = 15600;
+ else
+ unit = 62500;
+ }
+ if ((DB_TYPE_REMOVE_GLITCH << DB_CNTRL_OFF) == reg_db_mask)
+ debounce_enable = "debouncing filter (high and low) enabled|";
+ else if ((DB_TYPE_PRESERVE_LOW_GLITCH << DB_CNTRL_OFF) == reg_db_mask)
+ debounce_enable = "debouncing filter (low) enabled|";
+ else
+ debounce_enable = "debouncing filter (high) enabled|";
+
+ snprintf(debounce_value, 40,
+ "debouncing timeout is %u (us)|", time * unit);
+ } else {
+ debounce_enable = "debouncing filter disabled|";
+ snprintf(debounce_value, 30, " ");
+ }
+
seq_printf(s, "%s %s %s %s %s %s\n"
- " %s %s %s %s %s %s %s 0x%x\n",
+ " %s %s %s %s %s %s %s %s %s 0x%x\n",
level_trig, active_level, interrupt_enable,
interrupt_mask, wake_cntrl0, wake_cntrl1,
wake_cntrl2, pin_sts, pull_up_sel,
pull_up_enable, pull_down_enable,
- output_value, output_enable, pin_reg);
+ output_value, output_enable,
+ debounce_enable, debounce_value, pin_reg);
}
}
}
--
2.28.0
next reply other threads:[~2020-10-24 6:16 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-24 6:15 Coiby Xu [this message]
2020-10-25 17:12 ` [PATCH] pinctrl: amd: print debounce filter info in debugfs Andy Shevchenko
2020-10-26 15:16 ` Coiby Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201024061552.4497-1-coiby.xu@gmail.com \
--to=coiby.xu@gmail.com \
--cc=hdegoede@redhat.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).