From: <rui_feng@realsil.com.cn>
To: <arnd@arndb.de>, <gregkh@linuxfoundation.org>, <ulf.hansson@linaro.org>
Cc: <linux-kernel@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
Rui Feng <rui_feng@realsil.com.cn>
Subject: [PATCH v3 3/3] mmc: rtsx: Add SD Express mode support for RTS5261
Date: Thu, 29 Oct 2020 09:58:23 +0800 [thread overview]
Message-ID: <1603936703-3403-1-git-send-email-rui_feng@realsil.com.cn> (raw)
From: Rui Feng <rui_feng@realsil.com.cn>
RTS5261 support SD mode and PCIe/NVMe mode. The workflow is as follows.
1.RTS5261 work in SD mode and set MMC_CAPS2_SD_EXP flag.
2.If card is plugged in, Host send CMD8 to ask card's PCIe availability.
3.If the card has PCIe availability and WP is not set, init_sd_express() will be invoked,
RTS5261 switch to PCIe/NVMe mode.
4.Mmc driver handover it to NVMe driver.
5.If card is unplugged, RTS5261 will switch to SD mode.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
---
v2:
1.re-enable mmc caps in sd_power_on()
2.don't check write protect bit in init_sd_express()
v3:
1.add comment write protect switch is needed
2.add host->eject = true in the end of init_sd_express()
---
drivers/mmc/host/rtsx_pci_sdmmc.c | 58 +++++++++++++++++++++++++++++++
1 file changed, 58 insertions(+)
diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
index 2763a376b054..3b6474cce703 100644
--- a/drivers/mmc/host/rtsx_pci_sdmmc.c
+++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
@@ -895,7 +895,9 @@ static int sd_set_bus_width(struct realtek_pci_sdmmc *host,
static int sd_power_on(struct realtek_pci_sdmmc *host)
{
struct rtsx_pcr *pcr = host->pcr;
+ struct mmc_host *mmc = host->mmc;
int err;
+ u32 val;
if (host->power_state == SDMMC_POWER_ON)
return 0;
@@ -922,6 +924,21 @@ static int sd_power_on(struct realtek_pci_sdmmc *host)
if (err < 0)
return err;
+ if (PCI_PID(pcr) == PID_5261) {
+ if (pcr->extra_caps & EXTRA_CAPS_SD_EXPRESS)
+ mmc->caps2 |= MMC_CAP2_SD_EXP | MMC_CAP2_SD_EXP_1_2V;
+ /*
+ * HW read wp status when resuming from S3/S4,
+ * and then picks SD legacy interface if it's set
+ * in read-only mode.
+ */
+ val = rtsx_pci_readl(pcr, RTSX_BIPR);
+ if (val & SD_WRITE_PROTECT) {
+ pcr->extra_caps &= ~EXTRA_CAPS_SD_EXPRESS;
+ mmc->caps2 &= ~(MMC_CAP2_SD_EXP | MMC_CAP2_SD_EXP_1_2V);
+ }
+ }
+
host->power_state = SDMMC_POWER_ON;
return 0;
}
@@ -1308,6 +1325,44 @@ static int sdmmc_execute_tuning(struct mmc_host *mmc, u32 opcode)
return err;
}
+static int sdmmc_init_sd_express(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ u32 relink_time;
+ struct realtek_pci_sdmmc *host = mmc_priv(mmc);
+ struct rtsx_pcr *pcr = host->pcr;
+
+ /* Set relink_time for changing to PCIe card */
+ relink_time = 0x8FFF;
+
+ rtsx_pci_write_register(pcr, 0xFF01, 0xFF, relink_time);
+ rtsx_pci_write_register(pcr, 0xFF02, 0xFF, relink_time >> 8);
+ rtsx_pci_write_register(pcr, 0xFF03, 0x01, relink_time >> 16);
+
+ rtsx_pci_write_register(pcr, PETXCFG, 0x80, 0x80);
+ rtsx_pci_write_register(pcr, LDO_VCC_CFG0,
+ RTS5261_LDO1_OCP_THD_MASK,
+ pcr->option.sd_800mA_ocp_thd);
+
+ if (pcr->ops->disable_auto_blink)
+ pcr->ops->disable_auto_blink(pcr);
+
+ /* For PCIe/NVMe mode can't enter delink issue */
+ pcr->hw_param.interrupt_en &= ~(SD_INT_EN);
+ rtsx_pci_writel(pcr, RTSX_BIER, pcr->hw_param.interrupt_en);
+
+ rtsx_pci_write_register(pcr, RTS5260_AUTOLOAD_CFG4,
+ RTS5261_AUX_CLK_16M_EN, RTS5261_AUX_CLK_16M_EN);
+ rtsx_pci_write_register(pcr, RTS5261_FW_CFG0,
+ RTS5261_FW_ENTER_EXPRESS, RTS5261_FW_ENTER_EXPRESS);
+ rtsx_pci_write_register(pcr, RTS5261_FW_CFG1,
+ RTS5261_MCU_BUS_SEL_MASK | RTS5261_MCU_CLOCK_SEL_MASK
+ | RTS5261_MCU_CLOCK_GATING | RTS5261_DRIVER_ENABLE_FW,
+ RTS5261_MCU_CLOCK_SEL_16M | RTS5261_MCU_CLOCK_GATING
+ | RTS5261_DRIVER_ENABLE_FW);
+ host->eject = true;
+ return 0;
+}
+
static const struct mmc_host_ops realtek_pci_sdmmc_ops = {
.pre_req = sdmmc_pre_req,
.post_req = sdmmc_post_req,
@@ -1317,6 +1372,7 @@ static const struct mmc_host_ops realtek_pci_sdmmc_ops = {
.get_cd = sdmmc_get_cd,
.start_signal_voltage_switch = sdmmc_switch_voltage,
.execute_tuning = sdmmc_execute_tuning,
+ .init_sd_express = sdmmc_init_sd_express,
};
static void init_extra_caps(struct realtek_pci_sdmmc *host)
@@ -1338,6 +1394,8 @@ static void init_extra_caps(struct realtek_pci_sdmmc *host)
mmc->caps |= MMC_CAP_8_BIT_DATA;
if (pcr->extra_caps & EXTRA_CAPS_NO_MMC)
mmc->caps2 |= MMC_CAP2_NO_MMC;
+ if (pcr->extra_caps & EXTRA_CAPS_SD_EXPRESS)
+ mmc->caps2 |= MMC_CAP2_SD_EXP | MMC_CAP2_SD_EXP_1_2V;
}
static void realtek_init_host(struct realtek_pci_sdmmc *host)
--
2.17.1
next reply other threads:[~2020-10-29 2:00 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-29 1:58 rui_feng [this message]
2020-10-29 12:08 ` [PATCH v3 3/3] mmc: rtsx: Add SD Express mode support for RTS5261 Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1603936703-3403-1-git-send-email-rui_feng@realsil.com.cn \
--to=rui_feng@realsil.com.cn \
--cc=arnd@arndb.de \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).