[PATCH v5 4/5] ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx

From: Amelie Delaunay <amelie.delaunay@st.com>
To: Rob Herring <robh+dt@kernel.org>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Maxime Coquelin <mcoquelin.stm32@gmail.com>,
	Alexandre Torgue <alexandre.torgue@st.com>,
	Russell King <linux@armlinux.org.uk>,
	Heikki Krogerus <heikki.krogerus@linux.intel.com>,
	Badhri Jagan Sridharan <badhri@google.com>,
	Jun Li <lijun.kernel@gmail.com>
Cc: <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-usb@vger.kernel.org>,
	<linux-stm32@st-md-mailman.stormreply.com>,
	<linux-arm-kernel@lists.infradead.org>,
	Amelie Delaunay <amelie.delaunay@st.com>,
	Fabrice Gasnier <fabrice.gasnier@st.com>
Subject: [PATCH v5 4/5] ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx
Date: Fri, 6 Nov 2020 17:58:04 +0100	[thread overview]
Message-ID: <20201106165805.31534-5-amelie.delaunay@st.com> (raw)
In-Reply-To: <20201106165805.31534-1-amelie.delaunay@st.com>

This patch adds support for STUSB1600 USB Type-C port controller, used on
I2C4 on stm32mp15xx-dkx.
The default configuration on this board, on Type-C connector, is:
- Dual Power Role (DRP), so set power-role to "dual";
- Vbus limited to 500mA, so set typec-power-opmode to "default" (it means
  500mA in USB 2.0).
typec-power-opmode is used to reconfigure the STUSB1600 advertising of
current capability when its NVM is not in line with the board layout.
On stm32mp15xx-dkx, Vbus power source of STUSB1600 is 5V_VIN. So power
operation mode depends on the power supply used. To avoid any power
issues, it is better to limit Vbus to 500mA on this board.
ALERT# is the interrupt pin of STUSB1600. It needs an external pull-up, and
signal is active low.

USB OTG controller ID and Vbus signals are not connected on stm32mp15xx-dkx
boards, so disconnection are not detected.
Without DWC2 usb-role-switch:
- if you unplug the USB cable from the Type-C port, you have to manually
disconnect the USB gadget:
echo disconnect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
- Then you can plug the USB cable again in the Type-C port, and manually
reconnect the USB gadget:
echo connect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
With DWC2 usb-role-switch, USB gadget is dynamically disconnected or connected.

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
 arch/arm/boot/dts/stm32mp15-pinctrl.dtsi |  7 ++++++
 arch/arm/boot/dts/stm32mp15xx-dkx.dtsi   | 30 ++++++++++++++++++++++++
 2 files changed, 37 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index d84686e00370..d2e9e7ac3336 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1591,6 +1591,13 @@
 		};
 	};
 
+	stusb1600_pins_a: stusb1600-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 11, ANALOG)>;
+			bias-pull-up;
+		};
+	};
+
 	uart4_pins_a: uart4-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
index 93398cfae97e..ff324b151609 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
@@ -238,6 +238,30 @@
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
+	stusb1600@28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+		status = "okay";
+		vdd-supply = <&vin>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			typec-power-opmode = "default";
+
+			port {
+				con_usbotg_hs_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
@@ -648,6 +672,12 @@
 	phy-names = "usb2-phy";
 	usb-role-switch;
 	status = "okay";
+
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usbotg_hs_ep>;
+		};
+	};
 };
 
 &usbphyc {
-- 
2.17.1

