From: Ansuel Smith <ansuelsmth@gmail.com>
To: Amit Kucheria <amitk@kernel.org>
Cc: Ansuel Smith <ansuelsmth@gmail.com>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Zhang Rui <rui.zhang@intel.com>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-pm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v7 1/8] drivers: thermal: tsens: Add VER_0 tsens version
Date: Wed, 25 Nov 2020 18:48:18 +0100 [thread overview]
Message-ID: <20201125174826.24462-2-ansuelsmth@gmail.com> (raw)
In-Reply-To: <20201125174826.24462-1-ansuelsmth@gmail.com>
VER_0 is used to describe device based on tsens version before v0.1.
These device are devices based on msm8960 for example apq8064 or
ipq806x.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
drivers/thermal/qcom/tsens.c | 166 +++++++++++++++++++++++++++++------
drivers/thermal/qcom/tsens.h | 8 +-
2 files changed, 146 insertions(+), 28 deletions(-)
diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index d8ce3a687b80..bda965b3ac05 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -12,6 +12,7 @@
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
+#include <linux/mfd/syscon.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
#include <linux/regmap.h>
@@ -515,6 +516,15 @@ static irqreturn_t tsens_irq_thread(int irq, void *data)
dev_dbg(priv->dev, "[%u] %s: no violation: %d\n",
hw_id, __func__, temp);
}
+
+ if (tsens_version(priv) < VER_0_1) {
+ /* Constraint: There is only 1 interrupt control register for all
+ * 11 temperature sensor. So monitoring more than 1 sensor based
+ * on interrupts will yield inconsistent result. To overcome this
+ * issue we will monitor only sensor 0 which is the master sensor.
+ */
+ break;
+ }
}
return IRQ_HANDLED;
@@ -530,6 +540,13 @@ static int tsens_set_trips(void *_sensor, int low, int high)
int high_val, low_val, cl_high, cl_low;
u32 hw_id = s->hw_id;
+ if (tsens_version(priv) < VER_0_1) {
+ /* Pre v0.1 IP had a single register for each type of interrupt
+ * and thresholds
+ */
+ hw_id = 0;
+ }
+
dev_dbg(dev, "[%u] %s: proposed thresholds: (%d:%d)\n",
hw_id, __func__, low, high);
@@ -584,18 +601,21 @@ int get_temp_tsens_valid(const struct tsens_sensor *s, int *temp)
u32 valid;
int ret;
- ret = regmap_field_read(priv->rf[valid_idx], &valid);
- if (ret)
- return ret;
- while (!valid) {
- /* Valid bit is 0 for 6 AHB clock cycles.
- * At 19.2MHz, 1 AHB clock is ~60ns.
- * We should enter this loop very, very rarely.
- */
- ndelay(400);
+ /* VER_0 doesn't have VALID bit */
+ if (tsens_version(priv) >= VER_0_1) {
ret = regmap_field_read(priv->rf[valid_idx], &valid);
if (ret)
return ret;
+ while (!valid) {
+ /* Valid bit is 0 for 6 AHB clock cycles.
+ * At 19.2MHz, 1 AHB clock is ~60ns.
+ * We should enter this loop very, very rarely.
+ */
+ ndelay(400);
+ ret = regmap_field_read(priv->rf[valid_idx], &valid);
+ if (ret)
+ return ret;
+ }
}
/* Valid bit is set, OK to read the temperature */
@@ -608,15 +628,29 @@ int get_temp_common(const struct tsens_sensor *s, int *temp)
{
struct tsens_priv *priv = s->priv;
int hw_id = s->hw_id;
- int last_temp = 0, ret;
+ int last_temp = 0, ret, trdy;
+ unsigned long timeout;
- ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp);
- if (ret)
- return ret;
+ timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
+ do {
+ if (priv->rf[TRDY]) {
+ ret = regmap_field_read(priv->rf[TRDY], &trdy);
+ if (ret)
+ return ret;
+ if (!trdy)
+ continue;
+ }
+
+ ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp);
+ if (ret)
+ return ret;
- *temp = code_to_degc(last_temp, s) * 1000;
+ *temp = code_to_degc(last_temp, s) * 1000;
- return 0;
+ return 0;
+ } while (time_before(jiffies, timeout));
+
+ return -ETIMEDOUT;
}
#ifdef CONFIG_DEBUG_FS
@@ -738,19 +772,31 @@ int __init init_common(struct tsens_priv *priv)
priv->tm_offset = 0x1000;
}
- res = platform_get_resource(op, IORESOURCE_MEM, 0);
- tm_base = devm_ioremap_resource(dev, res);
- if (IS_ERR(tm_base)) {
- ret = PTR_ERR(tm_base);
- goto err_put_device;
+ if (tsens_version(priv) >= VER_0_1) {
+ res = platform_get_resource(op, IORESOURCE_MEM, 0);
+ tm_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(tm_base)) {
+ ret = PTR_ERR(tm_base);
+ goto err_put_device;
+ }
+
+ priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config);
+ } else { /* VER_0 share the same gcc regs using a syscon */
+ struct device *parent = priv->dev->parent;
+
+ if (parent)
+ priv->tm_map = syscon_node_to_regmap(parent->of_node);
}
- priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config);
- if (IS_ERR(priv->tm_map)) {
+ if (IS_ERR_OR_NULL(priv->tm_map)) {
ret = PTR_ERR(priv->tm_map);
goto err_put_device;
}
+ /* VER_0 have only tm_map */
+ if (!priv->srot_map)
+ priv->srot_map = priv->tm_map;
+
if (tsens_version(priv) > VER_0_1) {
for (i = VER_MAJOR; i <= VER_STEP; i++) {
priv->rf[i] = devm_regmap_field_alloc(dev, priv->srot_map,
@@ -769,6 +815,10 @@ int __init init_common(struct tsens_priv *priv)
ret = PTR_ERR(priv->rf[TSENS_EN]);
goto err_put_device;
}
+ /* in VER_0 TSENS need to be explicitly enabled */
+ if (tsens_version(priv) == VER_0)
+ regmap_field_write(priv->rf[TSENS_EN], 1);
+
ret = regmap_field_read(priv->rf[TSENS_EN], &enabled);
if (ret)
goto err_put_device;
@@ -791,6 +841,61 @@ int __init init_common(struct tsens_priv *priv)
goto err_put_device;
}
+ priv->rf[TSENS_EN] = devm_regmap_field_alloc(dev, priv->tm_map,
+ priv->fields[TSENS_EN]);
+ if (IS_ERR(priv->rf[TSENS_EN])) {
+ ret = PTR_ERR(priv->rf[TSENS_EN]);
+ goto err_put_device;
+ }
+
+ priv->rf[TSENS_SW_RST] = devm_regmap_field_alloc(
+ dev, priv->tm_map, priv->fields[TSENS_EN]);
+ if (IS_ERR(priv->rf[TSENS_EN])) {
+ ret = PTR_ERR(priv->rf[TSENS_EN]);
+ goto err_put_device;
+ }
+
+ priv->rf[LOW_INT_CLEAR_0] = devm_regmap_field_alloc(
+ dev, priv->tm_map, priv->fields[LOW_INT_CLEAR_0]);
+ if (IS_ERR(priv->rf[LOW_INT_CLEAR_0])) {
+ ret = PTR_ERR(priv->rf[LOW_INT_CLEAR_0]);
+ goto err_put_device;
+ }
+
+ priv->rf[UP_INT_CLEAR_0] = devm_regmap_field_alloc(
+ dev, priv->tm_map, priv->fields[UP_INT_CLEAR_0]);
+ if (IS_ERR(priv->rf[UP_INT_CLEAR_0])) {
+ ret = PTR_ERR(priv->rf[UP_INT_CLEAR_0]);
+ goto err_put_device;
+ }
+
+ /* VER_0 require to set MIN and MAX THRESH */
+ if (tsens_version(priv) < VER_0_1) {
+ priv->rf[MIN_THRESH_0] = devm_regmap_field_alloc(
+ dev, priv->tm_map, priv->fields[MIN_THRESH_0]);
+ if (IS_ERR(priv->rf[MIN_THRESH_0])) {
+ ret = PTR_ERR(priv->rf[MIN_THRESH_0]);
+ goto err_put_device;
+ }
+
+ priv->rf[MAX_THRESH_0] = devm_regmap_field_alloc(
+ dev, priv->tm_map, priv->fields[MAX_THRESH_0]);
+ if (IS_ERR(priv->rf[MAX_THRESH_0])) {
+ ret = PTR_ERR(priv->rf[MAX_THRESH_0]);
+ goto err_put_device;
+ }
+
+ regmap_field_write(priv->rf[MIN_THRESH_0], 0);
+ regmap_field_write(priv->rf[MAX_THRESH_0], 120000);
+ }
+
+ priv->rf[TRDY] =
+ devm_regmap_field_alloc(dev, priv->tm_map, priv->fields[TRDY]);
+ if (IS_ERR(priv->rf[TRDY])) {
+ ret = PTR_ERR(priv->rf[TRDY]);
+ goto err_put_device;
+ }
+
/* This loop might need changes if enum regfield_ids is reordered */
for (j = LAST_TEMP_0; j <= UP_THRESH_15; j += 16) {
for (i = 0; i < priv->feat->max_sensors; i++) {
@@ -844,7 +949,11 @@ int __init init_common(struct tsens_priv *priv)
}
spin_lock_init(&priv->ul_lock);
- tsens_enable_irq(priv);
+
+ /* VER_0 interrupt doesn't need to be enabled */
+ if (tsens_version(priv) >= VER_0_1)
+ tsens_enable_irq(priv);
+
tsens_debug_init(op);
err_put_device:
@@ -930,7 +1039,7 @@ static int tsens_register_irq(struct tsens_priv *priv, char *irqname,
irq_handler_t thread_fn)
{
struct platform_device *pdev;
- int ret, irq;
+ int ret, irq, irq_type = IRQF_ONESHOT;
pdev = of_find_device_by_node(priv->dev->of_node);
if (!pdev)
@@ -943,9 +1052,12 @@ static int tsens_register_irq(struct tsens_priv *priv, char *irqname,
if (irq == -ENXIO)
ret = 0;
} else {
- ret = devm_request_threaded_irq(&pdev->dev, irq,
- NULL, thread_fn,
- IRQF_ONESHOT,
+ /* VER_0 interrupt is TRIGGER_RISING, VER_0_1 and up is ONESHOT */
+ if (tsens_version(priv) == VER_0)
+ irq_type = IRQF_TRIGGER_RISING;
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq, thread_fn,
+ NULL, irq_type,
dev_name(&pdev->dev), priv);
if (ret)
dev_err(&pdev->dev, "%s: failed to get irq\n",
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index f40b625f897e..42c12639582f 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -13,6 +13,7 @@
#define CAL_DEGC_PT2 120
#define SLOPE_FACTOR 1000
#define SLOPE_DEFAULT 3200
+#define TIMEOUT_US 100
#define THRESHOLD_MAX_ADC_CODE 0x3ff
#define THRESHOLD_MIN_ADC_CODE 0x0
@@ -25,7 +26,8 @@ struct tsens_priv;
/* IP version numbers in ascending order */
enum tsens_ver {
- VER_0_1 = 0,
+ VER_0 = 0,
+ VER_0_1,
VER_1_X,
VER_2_X,
};
@@ -441,6 +443,10 @@ enum regfield_ids {
CRIT_THRESH_14,
CRIT_THRESH_15,
+ /* VER_0 MIN MAX THRESH */
+ MIN_THRESH_0,
+ MAX_THRESH_0,
+
/* WATCHDOG */
WDOG_BARK_STATUS,
WDOG_BARK_CLEAR,
--
2.29.2
next prev parent reply other threads:[~2020-11-26 2:13 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-25 17:48 [PATCH v7 0/8] Add support for ipq8064 tsens Ansuel Smith
2020-11-25 17:48 ` Ansuel Smith [this message]
2020-11-25 17:48 ` [PATCH v7 2/8] drivers: thermal: tsens: Don't hardcode sensor slope Ansuel Smith
2020-11-25 17:48 ` [PATCH v7 3/8] drivers: thermal: tsens: Convert msm8960 to reg_field Ansuel Smith
2020-11-25 17:48 ` [PATCH v7 4/8] drivers: thermal: tsens: Use init_common for msm8960 Ansuel Smith
2020-11-25 17:48 ` [PATCH v7 5/8] drivers: thermal: tsens: Fix bug in sensor enable " Ansuel Smith
2020-11-25 17:48 ` [PATCH v7 6/8] driver: thermal: tsens: Use get_temp_common " Ansuel Smith
2020-11-25 17:48 ` [PATCH v7 7/8] drivers: thermal: tsens: Add support for ipq8064-tsens Ansuel Smith
2020-11-25 17:48 ` [PATCH v7 8/8] dt-bindings: thermal: tsens: Document ipq8064 bindings Ansuel Smith
2020-11-30 16:59 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201125174826.24462-2-ansuelsmth@gmail.com \
--to=ansuelsmth@gmail.com \
--cc=agross@kernel.org \
--cc=amitk@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).