From: Christian Eggers <ceggers@arri.de>
To: Vladimir Oltean <olteanv@gmail.com>,
Jakub Kicinski <kuba@kernel.org>, Andrew Lunn <andrew@lunn.ch>,
Richard Cochran <richardcochran@gmail.com>,
"Rob Herring" <robh+dt@kernel.org>
Cc: Vivien Didelot <vivien.didelot@gmail.com>,
"David S . Miller" <davem@davemloft.net>,
Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>,
George McCollister <george.mccollister@gmail.com>,
Marek Vasut <marex@denx.de>,
Helmut Grohne <helmut.grohne@intenta.de>,
Paul Barker <pbarker@konsulko.com>,
Codrin Ciubotariu <codrin.ciubotariu@microchip.com>,
Tristram Ha <Tristram.Ha@microchip.com>,
Woojung Huh <woojung.huh@microchip.com>,
Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>,
Christian Eggers <ceggers@arri.de>, <netdev@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH net-next v4 4/9] net: dsa: microchip: ksz9477: basic interrupt support
Date: Tue, 1 Dec 2020 17:06:06 +0100 [thread overview]
Message-ID: <20201201160611.22129-5-ceggers@arri.de> (raw)
In-Reply-To: <20201201160611.22129-1-ceggers@arri.de>
Interrupts are required for TX time stamping. Probably they could also
be used for PHY connection status.
This patch only adds the basic infrastructure for interrupts, no
interrupts are finally enabled nor handled.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
---
Changes in v4:
--------------
- s/low active/active low/
- Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
drivers/net/dsa/microchip/ksz9477_i2c.c | 2 +
drivers/net/dsa/microchip/ksz9477_main.c | 68 ++++++++++++++++++++++++
drivers/net/dsa/microchip/ksz9477_spi.c | 2 +
drivers/net/dsa/microchip/ksz_common.h | 1 +
4 files changed, 73 insertions(+)
diff --git a/drivers/net/dsa/microchip/ksz9477_i2c.c b/drivers/net/dsa/microchip/ksz9477_i2c.c
index 4e053a25d077..4ed1f503044a 100644
--- a/drivers/net/dsa/microchip/ksz9477_i2c.c
+++ b/drivers/net/dsa/microchip/ksz9477_i2c.c
@@ -41,6 +41,8 @@ static int ksz9477_i2c_probe(struct i2c_client *i2c,
if (i2c->dev.platform_data)
dev->pdata = i2c->dev.platform_data;
+ dev->irq = i2c->irq;
+
ret = ksz9477_switch_register(dev);
/* Main DSA driver may not be started yet. */
diff --git a/drivers/net/dsa/microchip/ksz9477_main.c b/drivers/net/dsa/microchip/ksz9477_main.c
index c0b4cf66c904..fea5330ae894 100644
--- a/drivers/net/dsa/microchip/ksz9477_main.c
+++ b/drivers/net/dsa/microchip/ksz9477_main.c
@@ -5,9 +5,12 @@
* Copyright (C) 2017-2019 Microchip Technology Inc.
*/
+#include <linux/bits.h>
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/interrupt.h>
#include <linux/iopoll.h>
+#include <linux/irq.h>
#include <linux/platform_data/microchip-ksz.h>
#include <linux/phy.h>
#include <linux/if_bridge.h>
@@ -1528,6 +1531,54 @@ static const struct ksz_chip_data ksz9477_switch_chips[] = {
},
};
+static irqreturn_t ksz9477_switch_irq_thread(int irq, void *dev_id)
+{
+ struct ksz_device *dev = dev_id;
+ u32 data;
+ int port;
+ int ret;
+
+ /* Read global port interrupt status register */
+ ret = ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data);
+ if (ret)
+ return IRQ_NONE;
+
+ for (port = 0; port < dev->port_cnt; port++) {
+ u8 data8;
+
+ if (!(data & BIT(port)))
+ continue;
+
+ /* Read port interrupt status register */
+ ret = ksz_read8(dev, PORT_CTRL_ADDR(port, REG_PORT_INT_STATUS),
+ &data8);
+ if (ret)
+ return IRQ_NONE;
+
+ /* ToDo: Add specific handling of port interrupts */
+ }
+
+ return IRQ_NONE;
+}
+
+static int ksz9477_enable_port_interrupts(struct ksz_device *dev, bool enable)
+{
+ u32 data, mask = GENMASK(dev->port_cnt - 1, 0);
+ int ret;
+
+ ret = ksz_read32(dev, REG_SW_PORT_INT_MASK__4, &data);
+ if (ret)
+ return ret;
+
+ /* bits in REG_SW_PORT_INT_MASK__4 are active low */
+ if (enable)
+ data &= ~mask;
+ else
+ data |= mask;
+
+ return ksz_write32(dev, REG_SW_PORT_INT_MASK__4, data);
+}
+
static int ksz9477_switch_init(struct ksz_device *dev)
{
int i, ret;
@@ -1583,12 +1634,29 @@ static int ksz9477_switch_init(struct ksz_device *dev)
/* set the real number of ports */
dev->ds->num_ports = dev->port_cnt;
+ if (dev->irq > 0) {
+ ret = devm_request_threaded_irq(dev->dev, dev->irq, NULL,
+ ksz9477_switch_irq_thread,
+ IRQF_ONESHOT | IRQF_SHARED,
+ dev_name(dev->dev),
+ dev);
+ if (ret) {
+ dev_err(dev->dev, "failed to request IRQ.\n");
+ return ret;
+ }
+
+ ret = ksz9477_enable_port_interrupts(dev, true);
+ if (ret)
+ return ret;
+ }
return 0;
}
static void ksz9477_switch_exit(struct ksz_device *dev)
{
+ if (dev->irq > 0)
+ ksz9477_enable_port_interrupts(dev, false);
ksz9477_reset_switch(dev);
}
diff --git a/drivers/net/dsa/microchip/ksz9477_spi.c b/drivers/net/dsa/microchip/ksz9477_spi.c
index 15bc11b3cda4..fc0ac9e2c56d 100644
--- a/drivers/net/dsa/microchip/ksz9477_spi.c
+++ b/drivers/net/dsa/microchip/ksz9477_spi.c
@@ -48,6 +48,8 @@ static int ksz9477_spi_probe(struct spi_device *spi)
if (spi->dev.platform_data)
dev->pdata = spi->dev.platform_data;
+ dev->irq = spi->irq;
+
/* setup spi */
spi->mode = SPI_MODE_3;
ret = spi_setup(spi);
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index cf866e48ff66..5df4a7f9df02 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -55,6 +55,7 @@ struct ksz_device {
struct device *dev;
struct regmap *regmap[3];
+ int irq;
void *priv;
--
Christian Eggers
Embedded software developer
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRA 57918
Persoenlich haftender Gesellschafter: Arnold & Richter Cine Technik GmbH
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRB 54477
Geschaeftsfuehrer: Dr. Michael Neuhaeuser; Stephan Schenk; Walter Trauninger; Markus Zeiler
next prev parent reply other threads:[~2020-12-01 16:14 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-01 16:06 [PATCH net-next v4 0/9] net: dsa: microchip: PTP support for KSZ956x Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 1/9] net: dsa: microchip: rename ksz9477.c to ksz9477_main.c Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 2/9] dt-bindings: net: dsa: microchip,ksz: add interrupt property Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 3/9] net: dsa: microchip: ksz9477: move chip reset to ksz9477_switch_init() Christian Eggers
2020-12-01 16:06 ` Christian Eggers [this message]
2020-12-01 16:06 ` [PATCH net-next v4 5/9] net: dsa: microchip: ksz9477: add Posix clock support for chip PTP clock Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 6/9] net: ptp: add helper for one-step P2P clocks Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 7/9] net: dsa: microchip: ksz9477: initial hardware time stamping support Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 8/9] net: dsa: microchip: ksz9477: remaining " Christian Eggers
2020-12-01 16:06 ` [PATCH net-next v4 9/9] net: dsa: microchip: ksz9477: add periodic output support Christian Eggers
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201201160611.22129-5-ceggers@arri.de \
--to=ceggers@arri.de \
--cc=Tristram.Ha@microchip.com \
--cc=UNGLinuxDriver@microchip.com \
--cc=andrew@lunn.ch \
--cc=codrin.ciubotariu@microchip.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=george.mccollister@gmail.com \
--cc=helmut.grohne@intenta.de \
--cc=kuba@kernel.org \
--cc=kurt.kanzenbach@linutronix.de \
--cc=linux-kernel@vger.kernel.org \
--cc=marex@denx.de \
--cc=netdev@vger.kernel.org \
--cc=olteanv@gmail.com \
--cc=pbarker@konsulko.com \
--cc=richardcochran@gmail.com \
--cc=robh+dt@kernel.org \
--cc=vivien.didelot@gmail.com \
--cc=woojung.huh@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).