[PATCH] bus: mhi: core: Move to polling method to wait for MHI ready

From: Bhaumik Bhatt <bbhatt@codeaurora.org>
To: manivannan.sadhasivam@linaro.org
Cc: linux-arm-msm@vger.kernel.org, hemantk@codeaurora.org,
	jhugo@codeaurora.org, linux-kernel@vger.kernel.org,
	loic.poulain@linaro.org, carl.yin@quectel.com,
	naveen.kumar@quectel.com, Bhaumik Bhatt <bbhatt@codeaurora.org>
Subject: [PATCH] bus: mhi: core: Move to polling method to wait for MHI ready
Date: Thu, 18 Feb 2021 18:18:46 -0800	[thread overview]
Message-ID: <1613701126-38995-1-git-send-email-bbhatt@codeaurora.org> (raw)

In certain devices, it is likely that there is no incoming MHI
interrupt for a transition to MHI READY state. One such example
is the move from Pass Through to an SBL or AMSS execution
environment. In order to facilitate faster bootup times as there
is no need to wait until timeout_ms completes, MHI host can poll
every 25 milliseconds to check if device has entered MHI READY
until a maximum timeout of twice the timeout_ms is reached.

Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
 drivers/bus/mhi/core/pm.c | 32 ++++++++++++++++----------------
 1 file changed, 16 insertions(+), 16 deletions(-)

diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 65ebca8..ec0060c 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -9,6 +9,7 @@
 #include <linux/dma-direction.h>
 #include <linux/dma-mapping.h>
 #include <linux/interrupt.h>
+#include <linux/iopoll.h>
 #include <linux/list.h>
 #include <linux/mhi.h>
 #include <linux/module.h>
@@ -157,30 +158,29 @@ int mhi_ready_state_transition(struct mhi_controller *mhi_cntrl)
 	struct mhi_event *mhi_event;
 	enum mhi_pm_state cur_state;
 	struct device *dev = &mhi_cntrl->mhi_dev->dev;
-	u32 reset = 1, ready = 0;
+	u32 reset, ready;
 	int ret, i;
 
-	/* Wait for RESET to be cleared and READY bit to be set by the device */
-	wait_event_timeout(mhi_cntrl->state_event,
-			   MHI_PM_IN_FATAL_STATE(mhi_cntrl->pm_state) ||
-			   mhi_read_reg_field(mhi_cntrl, base, MHICTRL,
-					      MHICTRL_RESET_MASK,
-					      MHICTRL_RESET_SHIFT, &reset) ||
-			   mhi_read_reg_field(mhi_cntrl, base, MHISTATUS,
-					      MHISTATUS_READY_MASK,
-					      MHISTATUS_READY_SHIFT, &ready) ||
-			   (!reset && ready),
-			   msecs_to_jiffies(mhi_cntrl->timeout_ms));
-
 	/* Check if device entered error state */
 	if (MHI_PM_IN_FATAL_STATE(mhi_cntrl->pm_state)) {
 		dev_err(dev, "Device link is not accessible\n");
 		return -EIO;
 	}
 
-	/* Timeout if device did not transition to ready state */
-	if (reset || !ready) {
-		dev_err(dev, "Device Ready timeout\n");
+	/* Wait for RESET to be cleared and READY bit to be set by the device */
+	ret = readl_relaxed_poll_timeout(base + MHICTRL, reset,
+					 !(reset & MHICTRL_RESET_MASK), 25000,
+					 mhi_cntrl->timeout_ms * 1000);
+	if (ret) {
+		dev_err(dev, "Device failed to clear MHI Reset\n");
+		return -ETIMEDOUT;
+	}
+
+	ret = readl_relaxed_poll_timeout(base + MHISTATUS, ready,
+					 (ready & MHISTATUS_READY_MASK), 25000,
+					 mhi_cntrl->timeout_ms * 1000);
+	if (ret) {
+		dev_err(dev, "Device failed to enter MHI Ready\n");
 		return -ETIMEDOUT;
 	}
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

