[05/44] tty: cyclades, remove this orphan
diff mbox series

Message ID 20210302062214.29627-5-jslaby@suse.cz
State New, archived
Headers show
Series
  • [01/44] MAINTAINERS: orphan mxser
Related show

Commit Message

Jiri Slaby March 2, 2021, 6:21 a.m. UTC
The Cyclades driver was orphaned by commit d459883e6c54 (MAINTAINERS:
remove two dead e-mail) 13 years ago. Noone stepped up to take care of
them and to fix all the issues the driver has.

On the top of that, there is no way to obtain the firmware for Z cards
from the vendor as cyclades.com ceased to exist.

So it's time to drop the driver with all its traces.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
---
 Documentation/admin-guide/devices.txt         |   10 -
 .../driver-api/serial/cyclades_z.rst          |   11 -
 Documentation/driver-api/serial/index.rst     |    1 -
 Documentation/process/magic-number.rst        |    1 -
 .../it_IT/process/magic-number.rst            |    1 -
 .../zh_CN/process/magic-number.rst            |    1 -
 .../userspace-api/ioctl/ioctl-number.rst      |    1 -
 MAINTAINERS                                   |    7 -
 arch/powerpc/configs/ppc6xx_defconfig         |    1 -
 drivers/tty/Kconfig                           |   31 +-
 drivers/tty/Makefile                          |    1 -
 drivers/tty/cyclades.c                        | 4119 -----------------
 drivers/tty/serial/8250/Kconfig               |    5 +-
 include/linux/cyclades.h                      |  364 --
 include/linux/pci_ids.h                       |    8 -
 include/uapi/linux/cyclades.h                 |  494 --
 include/uapi/linux/major.h                    |    2 -
 include/uapi/linux/serial.h                   |    4 +-
 18 files changed, 5 insertions(+), 5057 deletions(-)
 delete mode 100644 Documentation/driver-api/serial/cyclades_z.rst
 delete mode 100644 drivers/tty/cyclades.c
 delete mode 100644 include/linux/cyclades.h
 delete mode 100644 include/uapi/linux/cyclades.h

Patch
diff mbox series

diff --git a/Documentation/admin-guide/devices.txt b/Documentation/admin-guide/devices.txt
index 63fd4e6a014b..b5bd9d46e031 100644
--- a/Documentation/admin-guide/devices.txt
+++ b/Documentation/admin-guide/devices.txt
@@ -477,11 +477,6 @@ 
   18 block	Sanyo CD-ROM
 		  0 = /dev/sjcd		Sanyo CD-ROM
 
-  19 char	Cyclades serial card
-		  0 = /dev/ttyC0	First Cyclades port
-		    ...
-		 31 = /dev/ttyC31	32nd Cyclades port
-
   19 block	"Double" compressed disk
 		  0 = /dev/double0	First compressed disk
 		    ...
@@ -493,11 +488,6 @@ 
 		See the Double documentation for the meaning of the
 		mirror devices.
 
-  20 char	Cyclades serial card - alternate devices
-		  0 = /dev/cub0		Callout device for ttyC0
-		    ...
-		 31 = /dev/cub31	Callout device for ttyC31
-
   20 block	Hitachi CD-ROM (under development)
 		  0 = /dev/hitcd	Hitachi CD-ROM
 
diff --git a/Documentation/driver-api/serial/cyclades_z.rst b/Documentation/driver-api/serial/cyclades_z.rst
deleted file mode 100644
index 532ff67e2f1c..000000000000
--- a/Documentation/driver-api/serial/cyclades_z.rst
+++ /dev/null
@@ -1,11 +0,0 @@ 
-================
-Cyclades-Z notes
-================
-
-The Cyclades-Z must have firmware loaded onto the card before it will
-operate.  This operation should be performed during system startup,
-
-The firmware, loader program and the latest device driver code are
-available from Cyclades at
-
-    ftp://ftp.cyclades.com/pub/cyclades/cyclades-z/linux/
diff --git a/Documentation/driver-api/serial/index.rst b/Documentation/driver-api/serial/index.rst
index 33ad10d05b26..21351b8c95a4 100644
--- a/Documentation/driver-api/serial/index.rst
+++ b/Documentation/driver-api/serial/index.rst
@@ -17,7 +17,6 @@  Serial drivers
 .. toctree::
     :maxdepth: 1
 
-    cyclades_z
     moxa-smartio
     n_gsm
     rocket
diff --git a/Documentation/process/magic-number.rst b/Documentation/process/magic-number.rst
index fa5a62f4150c..d4a30c09bd03 100644
--- a/Documentation/process/magic-number.rst
+++ b/Documentation/process/magic-number.rst
@@ -73,7 +73,6 @@  CMAGIC                0x0111           user                     ``include/linux/
 MKISS_DRIVER_MAGIC    0x04bf           mkiss_channel            ``drivers/net/mkiss.h``
 HDLC_MAGIC            0x239e           n_hdlc                   ``drivers/char/n_hdlc.c``
 APM_BIOS_MAGIC        0x4101           apm_user                 ``arch/x86/kernel/apm_32.c``
-CYCLADES_MAGIC        0x4359           cyclades_port            ``include/linux/cyclades.h``
 DB_MAGIC              0x4442           fc_info                  ``drivers/net/iph5526_novram.c``
 DL_MAGIC              0x444d           fc_info                  ``drivers/net/iph5526_novram.c``
 FASYNC_MAGIC          0x4601           fasync_struct            ``include/linux/fs.h``
diff --git a/Documentation/translations/it_IT/process/magic-number.rst b/Documentation/translations/it_IT/process/magic-number.rst
index 1af30f4228f2..0df2e7e32cd8 100644
--- a/Documentation/translations/it_IT/process/magic-number.rst
+++ b/Documentation/translations/it_IT/process/magic-number.rst
@@ -79,7 +79,6 @@  CMAGIC                0x0111           user                     ``include/linux/
 MKISS_DRIVER_MAGIC    0x04bf           mkiss_channel            ``drivers/net/mkiss.h``
 HDLC_MAGIC            0x239e           n_hdlc                   ``drivers/char/n_hdlc.c``
 APM_BIOS_MAGIC        0x4101           apm_user                 ``arch/x86/kernel/apm_32.c``
-CYCLADES_MAGIC        0x4359           cyclades_port            ``include/linux/cyclades.h``
 DB_MAGIC              0x4442           fc_info                  ``drivers/net/iph5526_novram.c``
 DL_MAGIC              0x444d           fc_info                  ``drivers/net/iph5526_novram.c``
 FASYNC_MAGIC          0x4601           fasync_struct            ``include/linux/fs.h``
diff --git a/Documentation/translations/zh_CN/process/magic-number.rst b/Documentation/translations/zh_CN/process/magic-number.rst
index 7bb9d4165ed3..82d62f6a4406 100644
--- a/Documentation/translations/zh_CN/process/magic-number.rst
+++ b/Documentation/translations/zh_CN/process/magic-number.rst
@@ -62,7 +62,6 @@  CMAGIC                0x0111           user                     ``include/linux/
 MKISS_DRIVER_MAGIC    0x04bf           mkiss_channel            ``drivers/net/mkiss.h``
 HDLC_MAGIC            0x239e           n_hdlc                   ``drivers/char/n_hdlc.c``
 APM_BIOS_MAGIC        0x4101           apm_user                 ``arch/x86/kernel/apm_32.c``
-CYCLADES_MAGIC        0x4359           cyclades_port            ``include/linux/cyclades.h``
 DB_MAGIC              0x4442           fc_info                  ``drivers/net/iph5526_novram.c``
 DL_MAGIC              0x444d           fc_info                  ``drivers/net/iph5526_novram.c``
 FASYNC_MAGIC          0x4601           fasync_struct            ``include/linux/fs.h``
diff --git a/Documentation/userspace-api/ioctl/ioctl-number.rst b/Documentation/userspace-api/ioctl/ioctl-number.rst
index 599bd4493944..0a7b408c0ec7 100644
--- a/Documentation/userspace-api/ioctl/ioctl-number.rst
+++ b/Documentation/userspace-api/ioctl/ioctl-number.rst
@@ -209,7 +209,6 @@  Code  Seq#    Include File                                           Comments
              linux/fs.h,
 'X'   all    fs/ocfs2/ocfs_fs.h                                      conflict!
 'X'   01     linux/pktcdvd.h                                         conflict!
-'Y'   all    linux/cyclades.h
 'Z'   14-15  drivers/message/fusion/mptctl.h
 '['   00-3F  linux/usb/tmc.h                                         USB Test and Measurement Devices
                                                                      <mailto:gregkh@linuxfoundation.org>
diff --git a/MAINTAINERS b/MAINTAINERS
index 7bfca0e2d5ab..fd45767da24c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4876,13 +4876,6 @@  S:	Maintained
 W:	http://www.armlinux.org.uk/
 F:	drivers/video/fbdev/cyber2000fb.*
 
-CYCLADES ASYNC MUX DRIVER
-S:	Orphan
-W:	http://www.cyclades.com/
-F:	drivers/tty/cyclades.c
-F:	include/linux/cyclades.h
-F:	include/uapi/linux/cyclades.h
-
 CYCLADES PC300 DRIVER
 S:	Orphan
 F:	drivers/net/wan/pc300*
diff --git a/arch/powerpc/configs/ppc6xx_defconfig b/arch/powerpc/configs/ppc6xx_defconfig
index 6677ac0da45a..1fd9d1260f9e 100644
--- a/arch/powerpc/configs/ppc6xx_defconfig
+++ b/arch/powerpc/configs/ppc6xx_defconfig
@@ -595,7 +595,6 @@  CONFIG_GAMEPORT_FM801=m
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_ROCKETPORT=m
-CONFIG_CYCLADES=m
 CONFIG_SYNCLINK_GT=m
 CONFIG_NOZOMI=m
 CONFIG_N_HDLC=m
diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
index e15cd6b5bb99..397523a8095e 100644
--- a/drivers/tty/Kconfig
+++ b/drivers/tty/Kconfig
@@ -181,7 +181,7 @@  config SERIAL_NONSTANDARD
 	help
 	  Say Y here if you have any non-standard serial boards -- boards
 	  which aren't supported using the standard "dumb" serial driver.
-	  This includes intelligent serial boards such as Cyclades,
+	  This includes intelligent serial boards such as
 	  Digiboards, etc. These are usually used for systems that need many
 	  serial ports because they serve many terminals or dial-in
 	  connections.
@@ -207,35 +207,6 @@  config ROCKETPORT
 	  If you want to compile this driver into the kernel, say Y here.  If
 	  you don't have a Comtrol RocketPort/RocketModem card installed, say N.
 
-config CYCLADES
-	tristate "Cyclades async mux support"
-	depends on SERIAL_NONSTANDARD && (PCI || ISA)
-	select FW_LOADER
-	help
-	  This driver supports Cyclades Z and Y multiserial boards.
-	  You would need something like this to connect more than two modems to
-	  your Linux box, for instance in order to become a dial-in server.
-
-	  For information about the Cyclades-Z card, read
-	  <file:Documentation/driver-api/serial/cyclades_z.rst>.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called cyclades.
-
-	  If you haven't heard about it, it's safe to say N.
-
-config CYZ_INTR
-	bool "Cyclades-Z interrupt mode operation"
-	depends on CYCLADES && PCI
-	help
-	  The Cyclades-Z family of multiport cards allows 2 (two) driver op
-	  modes: polling and interrupt. In polling mode, the driver will check
-	  the status of the Cyclades-Z ports every certain amount of time
-	  (which is called polling cycle and is configurable). In interrupt
-	  mode, it will use an interrupt line (IRQ) in order to check the
-	  status of the Cyclades-Z ports. The default op mode is polling. If
-	  unsure, say N.
-
 config MOXA_INTELLIO
 	tristate "Moxa Intellio support"
 	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
diff --git a/drivers/tty/Makefile b/drivers/tty/Makefile
index 730de6bf048b..94eb2bf75763 100644
--- a/drivers/tty/Makefile
+++ b/drivers/tty/Makefile
@@ -18,7 +18,6 @@  obj-$(CONFIG_SERIAL_DEV_BUS)	+= serdev/
 
 # tty drivers
 obj-$(CONFIG_AMIGA_BUILTIN_SERIAL) += amiserial.o
-obj-$(CONFIG_CYCLADES)		+= cyclades.o
 obj-$(CONFIG_ISI)		+= isicom.o
 obj-$(CONFIG_MOXA_INTELLIO)	+= moxa.o
 obj-$(CONFIG_MOXA_SMARTIO)	+= mxser.o
diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
deleted file mode 100644
index 097266342e5e..000000000000
--- a/drivers/tty/cyclades.c
+++ /dev/null
@@ -1,4119 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0
-#undef	BLOCKMOVE
-#define	Z_WAKE
-#undef	Z_EXT_CHARS_IN_BUFFER
-
-/*
- * This file contains the driver for the Cyclades async multiport
- * serial boards.
- *
- * Initially written by Randolph Bentson <bentson@grieg.seaslug.org>.
- * Modified and maintained by Marcio Saito <marcio@cyclades.com>.
- *
- * Copyright (C) 2007-2009 Jiri Slaby <jirislaby@gmail.com>
- *
- * Much of the design and some of the code came from serial.c
- * which was copyright (C) 1991, 1992  Linus Torvalds.  It was
- * extensively rewritten by Theodore Ts'o, 8/16/92 -- 9/14/92,
- * and then fixed as suggested by Michael K. Johnson 12/12/92.
- * Converted to pci probing and cleaned up by Jiri Slaby.
- *
- */
-
-#define CY_VERSION	"2.6"
-
-/* If you need to install more boards than NR_CARDS, change the constant
-   in the definition below. No other change is necessary to support up to
-   eight boards. Beyond that you'll have to extend cy_isa_addresses. */
-
-#define NR_CARDS	4
-
-/*
-   If the total number of ports is larger than NR_PORTS, change this
-   constant in the definition below. No other change is necessary to
-   support more boards/ports. */
-
-#define NR_PORTS	256
-
-#define ZO_V1	0
-#define ZO_V2	1
-#define ZE_V1	2
-
-#define	SERIAL_PARANOIA_CHECK
-#undef	CY_DEBUG_OPEN
-#undef	CY_DEBUG_THROTTLE
-#undef	CY_DEBUG_OTHER
-#undef	CY_DEBUG_IO
-#undef	CY_DEBUG_COUNT
-#undef	CY_DEBUG_DTR
-#undef	CY_DEBUG_INTERRUPTS
-#undef	CY_16Y_HACK
-#undef	CY_ENABLE_MONITORING
-#undef	CY_PCI_DEBUG
-
-/*
- * Include section
- */
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial.h>
-#include <linux/major.h>
-#include <linux/string.h>
-#include <linux/fcntl.h>
-#include <linux/ptrace.h>
-#include <linux/cyclades.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/bitops.h>
-#include <linux/firmware.h>
-#include <linux/device.h>
-#include <linux/slab.h>
-
-#include <linux/io.h>
-#include <linux/uaccess.h>
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-
-#include <linux/stat.h>
-#include <linux/proc_fs.h>
-#include <linux/seq_file.h>
-
-static void cy_send_xchar(struct tty_struct *tty, char ch);
-
-#ifndef SERIAL_XMIT_SIZE
-#define	SERIAL_XMIT_SIZE	(min(PAGE_SIZE, 4096))
-#endif
-
-/* firmware stuff */
-#define ZL_MAX_BLOCKS	16
-#define DRIVER_VERSION	0x02010203
-#define RAM_SIZE 0x80000
-
-enum zblock_type {
-	ZBLOCK_PRG = 0,
-	ZBLOCK_FPGA = 1
-};
-
-struct zfile_header {
-	char name[64];
-	char date[32];
-	char aux[32];
-	u32 n_config;
-	u32 config_offset;
-	u32 n_blocks;
-	u32 block_offset;
-	u32 reserved[9];
-} __attribute__ ((packed));
-
-struct zfile_config {
-	char name[64];
-	u32 mailbox;
-	u32 function;
-	u32 n_blocks;
-	u32 block_list[ZL_MAX_BLOCKS];
-} __attribute__ ((packed));
-
-struct zfile_block {
-	u32 type;
-	u32 file_offset;
-	u32 ram_offset;
-	u32 size;
-} __attribute__ ((packed));
-
-static struct tty_driver *cy_serial_driver;
-
-#ifdef CONFIG_ISA
-/* This is the address lookup table. The driver will probe for
-   Cyclom-Y/ISA boards at all addresses in here. If you want the
-   driver to probe addresses at a different address, add it to
-   this table.  If the driver is probing some other board and
-   causing problems, remove the offending address from this table.
-*/
-
-static unsigned int cy_isa_addresses[] = {
-	0xD0000,
-	0xD2000,
-	0xD4000,
-	0xD6000,
-	0xD8000,
-	0xDA000,
-	0xDC000,
-	0xDE000,
-	0, 0, 0, 0, 0, 0, 0, 0
-};
-
-#define NR_ISA_ADDRS ARRAY_SIZE(cy_isa_addresses)
-
-static long maddr[NR_CARDS];
-static int irq[NR_CARDS];
-
-module_param_hw_array(maddr, long, iomem, NULL, 0);
-module_param_hw_array(irq, int, irq, NULL, 0);
-
-#endif				/* CONFIG_ISA */
-
-/* This is the per-card data structure containing address, irq, number of
-   channels, etc. This driver supports a maximum of NR_CARDS cards.
-*/
-static struct cyclades_card cy_card[NR_CARDS];
-
-static int cy_next_channel;	/* next minor available */
-
-/*
- * This is used to look up the divisor speeds and the timeouts
- * We're normally limited to 15 distinct baud rates.  The extra
- * are accessed via settings in info->port.flags.
- *      0,     1,     2,     3,     4,     5,     6,     7,     8,     9,
- *     10,    11,    12,    13,    14,    15,    16,    17,    18,    19,
- *                                               HI            VHI
- *     20
- */
-static const int baud_table[] = {
-	0, 50, 75, 110, 134, 150, 200, 300, 600, 1200,
-	1800, 2400, 4800, 9600, 19200, 38400, 57600, 76800, 115200, 150000,
-	230400, 0
-};
-
-static const char baud_co_25[] = {	/* 25 MHz clock option table */
-	/* value =>    00    01   02    03    04 */
-	/* divide by    8    32   128   512  2048 */
-	0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x03, 0x03, 0x03, 0x02,
-	0x02, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
-};
-
-static const char baud_bpr_25[] = {	/* 25 MHz baud rate period table */
-	0x00, 0xf5, 0xa3, 0x6f, 0x5c, 0x51, 0xf5, 0xa3, 0x51, 0xa3,
-	0x6d, 0x51, 0xa3, 0x51, 0xa3, 0x51, 0x36, 0x29, 0x1b, 0x15
-};
-
-static const char baud_co_60[] = {	/* 60 MHz clock option table (CD1400 J) */
-	/* value =>    00    01   02    03    04 */
-	/* divide by    8    32   128   512  2048 */
-	0x00, 0x00, 0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x03, 0x03,
-	0x03, 0x02, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00,
-	0x00
-};
-
-static const char baud_bpr_60[] = {	/* 60 MHz baud rate period table (CD1400 J) */
-	0x00, 0x82, 0x21, 0xff, 0xdb, 0xc3, 0x92, 0x62, 0xc3, 0x62,
-	0x41, 0xc3, 0x62, 0xc3, 0x62, 0xc3, 0x82, 0x62, 0x41, 0x32,
-	0x21
-};
-
-static const char baud_cor3[] = {	/* receive threshold */
-	0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a,
-	0x0a, 0x0a, 0x0a, 0x09, 0x09, 0x08, 0x08, 0x08, 0x08, 0x07,
-	0x07
-};
-
-/*
- * The Cyclades driver implements HW flow control as any serial driver.
- * The cyclades_port structure member rflow and the vector rflow_thr
- * allows us to take advantage of a special feature in the CD1400 to avoid
- * data loss even when the system interrupt latency is too high. These flags
- * are to be used only with very special applications. Setting these flags
- * requires the use of a special cable (DTR and RTS reversed). In the new
- * CD1400-based boards (rev. 6.00 or later), there is no need for special
- * cables.
- */
-
-static const char rflow_thr[] = {	/* rflow threshold */
-	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-	0x00, 0x00, 0x00, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a,
-	0x0a
-};
-
-/*  The Cyclom-Ye has placed the sequential chips in non-sequential
- *  address order.  This look-up table overcomes that problem.
- */
-static const unsigned int cy_chip_offset[] = { 0x0000,
-	0x0400,
-	0x0800,
-	0x0C00,
-	0x0200,
-	0x0600,
-	0x0A00,
-	0x0E00
-};
-
-/* PCI related definitions */
-
-#ifdef CONFIG_PCI
-static const struct pci_device_id cy_pci_dev_id[] = {
-	/* PCI < 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Lo) },
-	/* PCI > 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Hi) },
-	/* 4Y PCI < 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Lo) },
-	/* 4Y PCI > 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Hi) },
-	/* 8Y PCI < 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Lo) },
-	/* 8Y PCI > 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Hi) },
-	/* Z PCI < 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Lo) },
-	/* Z PCI > 1Mb */
-	{ PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Hi) },
-	{ }			/* end of table */
-};
-MODULE_DEVICE_TABLE(pci, cy_pci_dev_id);
-#endif
-
-static void cy_start(struct tty_struct *);
-static void cy_set_line_char(struct cyclades_port *, struct tty_struct *);
-static int cyz_issue_cmd(struct cyclades_card *, __u32, __u8, __u32);
-#ifdef CONFIG_ISA
-static unsigned detect_isa_irq(void __iomem *);
-#endif				/* CONFIG_ISA */
-
-#ifndef CONFIG_CYZ_INTR
-static void cyz_poll(struct timer_list *);
-
-/* The Cyclades-Z polling cycle is defined by this variable */
-static long cyz_polling_cycle = CZ_DEF_POLL;
-
-static DEFINE_TIMER(cyz_timerlist, cyz_poll);
-
-#else				/* CONFIG_CYZ_INTR */
-static void cyz_rx_restart(struct timer_list *);
-#endif				/* CONFIG_CYZ_INTR */
-
-static void cyy_writeb(struct cyclades_port *port, u32 reg, u8 val)
-{
-	struct cyclades_card *card = port->card;
-
-	cy_writeb(port->u.cyy.base_addr + (reg << card->bus_index), val);
-}
-
-static u8 cyy_readb(struct cyclades_port *port, u32 reg)
-{
-	struct cyclades_card *card = port->card;
-
-	return readb(port->u.cyy.base_addr + (reg << card->bus_index));
-}
-
-static inline bool cy_is_Z(struct cyclades_card *card)
-{
-	return card->num_chips == (unsigned int)-1;
-}
-
-static inline bool __cyz_fpga_loaded(struct RUNTIME_9060 __iomem *ctl_addr)
-{
-	return readl(&ctl_addr->init_ctrl) & (1 << 17);
-}
-
-static inline bool cyz_fpga_loaded(struct cyclades_card *card)
-{
-	return __cyz_fpga_loaded(card->ctl_addr.p9060);
-}
-
-static bool cyz_is_loaded(struct cyclades_card *card)
-{
-	struct FIRM_ID __iomem *fw_id = card->base_addr + ID_ADDRESS;
-
-	return (card->hw_ver == ZO_V1 || cyz_fpga_loaded(card)) &&
-			readl(&fw_id->signature) == ZFIRM_ID;
-}
-
-static int serial_paranoia_check(struct cyclades_port *info,
-		const char *name, const char *routine)
-{
-#ifdef SERIAL_PARANOIA_CHECK
-	if (!info) {
-		printk(KERN_WARNING "cyc Warning: null cyclades_port for (%s) "
-				"in %s\n", name, routine);
-		return 1;
-	}
-
-	if (info->magic != CYCLADES_MAGIC) {
-		printk(KERN_WARNING "cyc Warning: bad magic number for serial "
-				"struct (%s) in %s\n", name, routine);
-		return 1;
-	}
-#endif
-	return 0;
-}
-
-/***********************************************************/
-/********* Start of block of Cyclom-Y specific code ********/
-
-/* This routine waits up to 1000 micro-seconds for the previous
-   command to the Cirrus chip to complete and then issues the
-   new command.  An error is returned if the previous command
-   didn't finish within the time limit.
-
-   This function is only called from inside spinlock-protected code.
- */
-static int __cyy_issue_cmd(void __iomem *base_addr, u8 cmd, int index)
-{
-	void __iomem *ccr = base_addr + (CyCCR << index);
-	unsigned int i;
-
-	/* Check to see that the previous command has completed */
-	for (i = 0; i < 100; i++) {
-		if (readb(ccr) == 0)
-			break;
-		udelay(10L);
-	}
-	/* if the CCR never cleared, the previous command
-	   didn't finish within the "reasonable time" */
-	if (i == 100)
-		return -1;
-
-	/* Issue the new command */
-	cy_writeb(ccr, cmd);
-
-	return 0;
-}
-
-static inline int cyy_issue_cmd(struct cyclades_port *port, u8 cmd)
-{
-	return __cyy_issue_cmd(port->u.cyy.base_addr, cmd,
-			port->card->bus_index);
-}
-
-#ifdef CONFIG_ISA
-/* ISA interrupt detection code */
-static unsigned detect_isa_irq(void __iomem *address)
-{
-	int irq;
-	unsigned long irqs, flags;
-	int save_xir, save_car;
-	int index = 0;		/* IRQ probing is only for ISA */
-
-	/* forget possible initially masked and pending IRQ */
-	irq = probe_irq_off(probe_irq_on());
-
-	/* Clear interrupts on the board first */
-	cy_writeb(address + (Cy_ClrIntr << index), 0);
-	/* Cy_ClrIntr is 0x1800 */
-
-	irqs = probe_irq_on();
-	/* Wait ... */
-	msleep(5);
-
-	/* Enable the Tx interrupts on the CD1400 */
-	local_irq_save(flags);
-	cy_writeb(address + (CyCAR << index), 0);
-	__cyy_issue_cmd(address, CyCHAN_CTL | CyENB_XMTR, index);
-
-	cy_writeb(address + (CyCAR << index), 0);
-	cy_writeb(address + (CySRER << index),
-		  readb(address + (CySRER << index)) | CyTxRdy);
-	local_irq_restore(flags);
-
-	/* Wait ... */
-	msleep(5);
-
-	/* Check which interrupt is in use */
-	irq = probe_irq_off(irqs);
-
-	/* Clean up */
-	save_xir = (u_char) readb(address + (CyTIR << index));
-	save_car = readb(address + (CyCAR << index));
-	cy_writeb(address + (CyCAR << index), (save_xir & 0x3));
-	cy_writeb(address + (CySRER << index),
-		  readb(address + (CySRER << index)) & ~CyTxRdy);
-	cy_writeb(address + (CyTIR << index), (save_xir & 0x3f));
-	cy_writeb(address + (CyCAR << index), (save_car));
-	cy_writeb(address + (Cy_ClrIntr << index), 0);
-	/* Cy_ClrIntr is 0x1800 */
-
-	return (irq > 0) ? irq : 0;
-}
-#endif				/* CONFIG_ISA */
-
-static void cyy_chip_rx(struct cyclades_card *cinfo, int chip,
-		void __iomem *base_addr)
-{
-	struct cyclades_port *info;
-	struct tty_port *port;
-	int len, index = cinfo->bus_index;
-	u8 ivr, save_xir, channel, save_car, data, char_count;
-
-#ifdef CY_DEBUG_INTERRUPTS
-	printk(KERN_DEBUG "cyy_interrupt: rcvd intr, chip %d\n", chip);
-#endif
-	/* determine the channel & change to that context */
-	save_xir = readb(base_addr + (CyRIR << index));
-	channel = save_xir & CyIRChannel;
-	info = &cinfo->ports[channel + chip * 4];
-	port = &info->port;
-	save_car = cyy_readb(info, CyCAR);
-	cyy_writeb(info, CyCAR, save_xir);
-	ivr = cyy_readb(info, CyRIVR) & CyIVRMask;
-
-	/* there is an open port for this data */
-	if (ivr == CyIVRRxEx) {	/* exception */
-		data = cyy_readb(info, CyRDSR);
-
-		/* For statistics only */
-		if (data & CyBREAK)
-			info->icount.brk++;
-		else if (data & CyFRAME)
-			info->icount.frame++;
-		else if (data & CyPARITY)
-			info->icount.parity++;
-		else if (data & CyOVERRUN)
-			info->icount.overrun++;
-
-		if (data & info->ignore_status_mask) {
-			info->icount.rx++;
-			return;
-		}
-		if (tty_buffer_request_room(port, 1)) {
-			if (data & info->read_status_mask) {
-				if (data & CyBREAK) {
-					tty_insert_flip_char(port,
-						cyy_readb(info, CyRDSR),
-						TTY_BREAK);
-					info->icount.rx++;
-					if (port->flags & ASYNC_SAK) {
-						struct tty_struct *tty =
-							tty_port_tty_get(port);
-						if (tty) {
-							do_SAK(tty);
-							tty_kref_put(tty);
-						}
-					}
-				} else if (data & CyFRAME) {
-					tty_insert_flip_char(port,
-						cyy_readb(info, CyRDSR),
-						TTY_FRAME);
-					info->icount.rx++;
-					info->idle_stats.frame_errs++;
-				} else if (data & CyPARITY) {
-					/* Pieces of seven... */
-					tty_insert_flip_char(port,
-						cyy_readb(info, CyRDSR),
-						TTY_PARITY);
-					info->icount.rx++;
-					info->idle_stats.parity_errs++;
-				} else if (data & CyOVERRUN) {
-					tty_insert_flip_char(port, 0,
-							TTY_OVERRUN);
-					info->icount.rx++;
-					/* If the flip buffer itself is
-					   overflowing, we still lose
-					   the next incoming character.
-					 */
-					tty_insert_flip_char(port,
-						cyy_readb(info, CyRDSR),
-						TTY_FRAME);
-					info->icount.rx++;
-					info->idle_stats.overruns++;
-				/* These two conditions may imply */
-				/* a normal read should be done. */
-				/* } else if(data & CyTIMEOUT) { */
-				/* } else if(data & CySPECHAR) { */
-				} else {
-					tty_insert_flip_char(port, 0,
-							TTY_NORMAL);
-					info->icount.rx++;
-				}
-			} else {
-				tty_insert_flip_char(port, 0, TTY_NORMAL);
-				info->icount.rx++;
-			}
-		} else {
-			/* there was a software buffer overrun and nothing
-			 * could be done about it!!! */
-			info->icount.buf_overrun++;
-			info->idle_stats.overruns++;
-		}
-	} else {	/* normal character reception */
-		/* load # chars available from the chip */
-		char_count = cyy_readb(info, CyRDCR);
-
-#ifdef CY_ENABLE_MONITORING
-		++info->mon.int_count;
-		info->mon.char_count += char_count;
-		if (char_count > info->mon.char_max)
-			info->mon.char_max = char_count;
-		info->mon.char_last = char_count;
-#endif
-		len = tty_buffer_request_room(port, char_count);
-		while (len--) {
-			data = cyy_readb(info, CyRDSR);
-			tty_insert_flip_char(port, data, TTY_NORMAL);
-			info->idle_stats.recv_bytes++;
-			info->icount.rx++;
-#ifdef CY_16Y_HACK
-			udelay(10L);
-#endif
-		}
-		info->idle_stats.recv_idle = jiffies;
-	}
-	tty_schedule_flip(port);
-
-	/* end of service */
-	cyy_writeb(info, CyRIR, save_xir & 0x3f);
-	cyy_writeb(info, CyCAR, save_car);
-}
-
-static void cyy_chip_tx(struct cyclades_card *cinfo, unsigned int chip,
-		void __iomem *base_addr)
-{
-	struct cyclades_port *info;
-	struct tty_struct *tty;
-	int char_count, index = cinfo->bus_index;
-	u8 save_xir, channel, save_car, outch;
-
-	/* Since we only get here when the transmit buffer
-	   is empty, we know we can always stuff a dozen
-	   characters. */
-#ifdef CY_DEBUG_INTERRUPTS
-	printk(KERN_DEBUG "cyy_interrupt: xmit intr, chip %d\n", chip);
-#endif
-
-	/* determine the channel & change to that context */
-	save_xir = readb(base_addr + (CyTIR << index));
-	channel = save_xir & CyIRChannel;
-	save_car = readb(base_addr + (CyCAR << index));
-	cy_writeb(base_addr + (CyCAR << index), save_xir);
-
-	info = &cinfo->ports[channel + chip * 4];
-	tty = tty_port_tty_get(&info->port);
-	if (tty == NULL) {
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyTxRdy);
-		goto end;
-	}
-
-	/* load the on-chip space for outbound data */
-	char_count = info->xmit_fifo_size;
-
-	if (info->x_char) {	/* send special char */
-		outch = info->x_char;
-		cyy_writeb(info, CyTDR, outch);
-		char_count--;
-		info->icount.tx++;
-		info->x_char = 0;
-	}
-
-	if (info->breakon || info->breakoff) {
-		if (info->breakon) {
-			cyy_writeb(info, CyTDR, 0);
-			cyy_writeb(info, CyTDR, 0x81);
-			info->breakon = 0;
-			char_count -= 2;
-		}
-		if (info->breakoff) {
-			cyy_writeb(info, CyTDR, 0);
-			cyy_writeb(info, CyTDR, 0x83);
-			info->breakoff = 0;
-			char_count -= 2;
-		}
-	}
-
-	while (char_count-- > 0) {
-		if (!info->xmit_cnt) {
-			if (cyy_readb(info, CySRER) & CyTxMpty) {
-				cyy_writeb(info, CySRER,
-					cyy_readb(info, CySRER) & ~CyTxMpty);
-			} else {
-				cyy_writeb(info, CySRER, CyTxMpty |
-					(cyy_readb(info, CySRER) & ~CyTxRdy));
-			}
-			goto done;
-		}
-		if (info->port.xmit_buf == NULL) {
-			cyy_writeb(info, CySRER,
-				cyy_readb(info, CySRER) & ~CyTxRdy);
-			goto done;
-		}
-		if (tty->stopped || tty->hw_stopped) {
-			cyy_writeb(info, CySRER,
-				cyy_readb(info, CySRER) & ~CyTxRdy);
-			goto done;
-		}
-		/* Because the Embedded Transmit Commands have been enabled,
-		 * we must check to see if the escape character, NULL, is being
-		 * sent. If it is, we must ensure that there is room for it to
-		 * be doubled in the output stream.  Therefore we no longer
-		 * advance the pointer when the character is fetched, but
-		 * rather wait until after the check for a NULL output
-		 * character. This is necessary because there may not be room
-		 * for the two chars needed to send a NULL.)
-		 */
-		outch = info->port.xmit_buf[info->xmit_tail];
-		if (outch) {
-			info->xmit_cnt--;
-			info->xmit_tail = (info->xmit_tail + 1) &
-					(SERIAL_XMIT_SIZE - 1);
-			cyy_writeb(info, CyTDR, outch);
-			info->icount.tx++;
-		} else {
-			if (char_count > 1) {
-				info->xmit_cnt--;
-				info->xmit_tail = (info->xmit_tail + 1) &
-					(SERIAL_XMIT_SIZE - 1);
-				cyy_writeb(info, CyTDR, outch);
-				cyy_writeb(info, CyTDR, 0);
-				info->icount.tx++;
-				char_count--;
-			}
-		}
-	}
-
-done:
-	tty_wakeup(tty);
-	tty_kref_put(tty);
-end:
-	/* end of service */
-	cyy_writeb(info, CyTIR, save_xir & 0x3f);
-	cyy_writeb(info, CyCAR, save_car);
-}
-
-static void cyy_chip_modem(struct cyclades_card *cinfo, int chip,
-		void __iomem *base_addr)
-{
-	struct cyclades_port *info;
-	struct tty_struct *tty;
-	int index = cinfo->bus_index;
-	u8 save_xir, channel, save_car, mdm_change, mdm_status;
-
-	/* determine the channel & change to that context */
-	save_xir = readb(base_addr + (CyMIR << index));
-	channel = save_xir & CyIRChannel;
-	info = &cinfo->ports[channel + chip * 4];
-	save_car = cyy_readb(info, CyCAR);
-	cyy_writeb(info, CyCAR, save_xir);
-
-	mdm_change = cyy_readb(info, CyMISR);
-	mdm_status = cyy_readb(info, CyMSVR1);
-
-	tty = tty_port_tty_get(&info->port);
-	if (!tty)
-		goto end;
-
-	if (mdm_change & CyANY_DELTA) {
-		/* For statistics only */
-		if (mdm_change & CyDCD)
-			info->icount.dcd++;
-		if (mdm_change & CyCTS)
-			info->icount.cts++;
-		if (mdm_change & CyDSR)
-			info->icount.dsr++;
-		if (mdm_change & CyRI)
-			info->icount.rng++;
-
-		wake_up_interruptible(&info->port.delta_msr_wait);
-	}
-
-	if ((mdm_change & CyDCD) && tty_port_check_carrier(&info->port)) {
-		if (mdm_status & CyDCD)
-			wake_up_interruptible(&info->port.open_wait);
-		else
-			tty_hangup(tty);
-	}
-	if ((mdm_change & CyCTS) && tty_port_cts_enabled(&info->port)) {
-		if (tty->hw_stopped) {
-			if (mdm_status & CyCTS) {
-				/* cy_start isn't used
-				   because... !!! */
-				tty->hw_stopped = 0;
-				cyy_writeb(info, CySRER,
-					cyy_readb(info, CySRER) | CyTxRdy);
-				tty_wakeup(tty);
-			}
-		} else {
-			if (!(mdm_status & CyCTS)) {
-				/* cy_stop isn't used
-				   because ... !!! */
-				tty->hw_stopped = 1;
-				cyy_writeb(info, CySRER,
-					cyy_readb(info, CySRER) & ~CyTxRdy);
-			}
-		}
-	}
-/*	if (mdm_change & CyDSR) {
-	}
-	if (mdm_change & CyRI) {
-	}*/
-	tty_kref_put(tty);
-end:
-	/* end of service */
-	cyy_writeb(info, CyMIR, save_xir & 0x3f);
-	cyy_writeb(info, CyCAR, save_car);
-}
-
-/* The real interrupt service routine is called
-   whenever the card wants its hand held--chars
-   received, out buffer empty, modem change, etc.
- */
-static irqreturn_t cyy_interrupt(int irq, void *dev_id)
-{
-	int status;
-	struct cyclades_card *cinfo = dev_id;
-	void __iomem *base_addr, *card_base_addr;
-	unsigned int chip, too_many, had_work;
-	int index;
-
-	if (unlikely(cinfo == NULL)) {
-#ifdef CY_DEBUG_INTERRUPTS
-		printk(KERN_DEBUG "cyy_interrupt: spurious interrupt %d\n",
-				irq);
-#endif
-		return IRQ_NONE;	/* spurious interrupt */
-	}
-
-	card_base_addr = cinfo->base_addr;
-	index = cinfo->bus_index;
-
-	/* card was not initialized yet (e.g. DEBUG_SHIRQ) */
-	if (unlikely(card_base_addr == NULL))
-		return IRQ_HANDLED;
-
-	/* This loop checks all chips in the card.  Make a note whenever
-	   _any_ chip had some work to do, as this is considered an
-	   indication that there will be more to do.  Only when no chip
-	   has any work does this outermost loop exit.
-	 */
-	do {
-		had_work = 0;
-		for (chip = 0; chip < cinfo->num_chips; chip++) {
-			base_addr = cinfo->base_addr +
-					(cy_chip_offset[chip] << index);
-			too_many = 0;
-			while ((status = readb(base_addr +
-						(CySVRR << index))) != 0x00) {
-				had_work++;
-			/* The purpose of the following test is to ensure that
-			   no chip can monopolize the driver.  This forces the
-			   chips to be checked in a round-robin fashion (after
-			   draining each of a bunch (1000) of characters).
-			 */
-				if (1000 < too_many++)
-					break;
-				spin_lock(&cinfo->card_lock);
-				if (status & CySRReceive) /* rx intr */
-					cyy_chip_rx(cinfo, chip, base_addr);
-				if (status & CySRTransmit) /* tx intr */
-					cyy_chip_tx(cinfo, chip, base_addr);
-				if (status & CySRModem) /* modem intr */
-					cyy_chip_modem(cinfo, chip, base_addr);
-				spin_unlock(&cinfo->card_lock);
-			}
-		}
-	} while (had_work);
-
-	/* clear interrupts */
-	spin_lock(&cinfo->card_lock);
-	cy_writeb(card_base_addr + (Cy_ClrIntr << index), 0);
-	/* Cy_ClrIntr is 0x1800 */
-	spin_unlock(&cinfo->card_lock);
-	return IRQ_HANDLED;
-}				/* cyy_interrupt */
-
-static void cyy_change_rts_dtr(struct cyclades_port *info, unsigned int set,
-		unsigned int clear)
-{
-	struct cyclades_card *card = info->card;
-	int channel = info->line - card->first_line;
-	u32 rts, dtr, msvrr, msvrd;
-
-	channel &= 0x03;
-
-	if (info->rtsdtr_inv) {
-		msvrr = CyMSVR2;
-		msvrd = CyMSVR1;
-		rts = CyDTR;
-		dtr = CyRTS;
-	} else {
-		msvrr = CyMSVR1;
-		msvrd = CyMSVR2;
-		rts = CyRTS;
-		dtr = CyDTR;
-	}
-	if (set & TIOCM_RTS) {
-		cyy_writeb(info, CyCAR, channel);
-		cyy_writeb(info, msvrr, rts);
-	}
-	if (clear & TIOCM_RTS) {
-		cyy_writeb(info, CyCAR, channel);
-		cyy_writeb(info, msvrr, ~rts);
-	}
-	if (set & TIOCM_DTR) {
-		cyy_writeb(info, CyCAR, channel);
-		cyy_writeb(info, msvrd, dtr);
-#ifdef CY_DEBUG_DTR
-		printk(KERN_DEBUG "cyc:set_modem_info raising DTR\n");
-		printk(KERN_DEBUG "     status: 0x%x, 0x%x\n",
-			cyy_readb(info, CyMSVR1),
-			cyy_readb(info, CyMSVR2));
-#endif
-	}
-	if (clear & TIOCM_DTR) {
-		cyy_writeb(info, CyCAR, channel);
-		cyy_writeb(info, msvrd, ~dtr);
-#ifdef CY_DEBUG_DTR
-		printk(KERN_DEBUG "cyc:set_modem_info dropping DTR\n");
-		printk(KERN_DEBUG "     status: 0x%x, 0x%x\n",
-			cyy_readb(info, CyMSVR1),
-			cyy_readb(info, CyMSVR2));
-#endif
-	}
-}
-
-/***********************************************************/
-/********* End of block of Cyclom-Y specific code **********/
-/******** Start of block of Cyclades-Z specific code *******/
-/***********************************************************/
-
-static int
-cyz_fetch_msg(struct cyclades_card *cinfo,
-		__u32 *channel, __u8 *cmd, __u32 *param)
-{
-	struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl;
-	unsigned long loc_doorbell;
-
-	loc_doorbell = readl(&cinfo->ctl_addr.p9060->loc_doorbell);
-	if (loc_doorbell) {
-		*cmd = (char)(0xff & loc_doorbell);
-		*channel = readl(&board_ctrl->fwcmd_channel);
-		*param = (__u32) readl(&board_ctrl->fwcmd_param);
-		cy_writel(&cinfo->ctl_addr.p9060->loc_doorbell, 0xffffffff);
-		return 1;
-	}
-	return 0;
-}				/* cyz_fetch_msg */
-
-static int
-cyz_issue_cmd(struct cyclades_card *cinfo,
-		__u32 channel, __u8 cmd, __u32 param)
-{
-	struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl;
-	__u32 __iomem *pci_doorbell;
-	unsigned int index;
-
-	if (!cyz_is_loaded(cinfo))
-		return -1;
-
-	index = 0;
-	pci_doorbell = &cinfo->ctl_addr.p9060->pci_doorbell;
-	while ((readl(pci_doorbell) & 0xff) != 0) {
-		if (index++ == 1000)
-			return (int)(readl(pci_doorbell) & 0xff);
-		udelay(50L);
-	}
-	cy_writel(&board_ctrl->hcmd_channel, channel);
-	cy_writel(&board_ctrl->hcmd_param, param);
-	cy_writel(pci_doorbell, (long)cmd);
-
-	return 0;
-}				/* cyz_issue_cmd */
-
-static void cyz_handle_rx(struct cyclades_port *info)
-{
-	struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl;
-	struct cyclades_card *cinfo = info->card;
-	struct tty_port *port = &info->port;
-	unsigned int char_count;
-	int len;
-#ifdef BLOCKMOVE
-	unsigned char *buf;
-#else
-	char data;
-#endif
-	__u32 rx_put, rx_get, new_rx_get, rx_bufsize, rx_bufaddr;
-
-	rx_get = new_rx_get = readl(&buf_ctrl->rx_get);
-	rx_put = readl(&buf_ctrl->rx_put);
-	rx_bufsize = readl(&buf_ctrl->rx_bufsize);
-	rx_bufaddr = readl(&buf_ctrl->rx_bufaddr);
-	if (rx_put >= rx_get)
-		char_count = rx_put - rx_get;
-	else
-		char_count = rx_put - rx_get + rx_bufsize;
-
-	if (!char_count)
-		return;
-
-#ifdef CY_ENABLE_MONITORING
-	info->mon.int_count++;
-	info->mon.char_count += char_count;
-	if (char_count > info->mon.char_max)
-		info->mon.char_max = char_count;
-	info->mon.char_last = char_count;
-#endif
-
-#ifdef BLOCKMOVE
-	/* we'd like to use memcpy(t, f, n) and memset(s, c, count)
-	   for performance, but because of buffer boundaries, there
-	   may be several steps to the operation */
-	while (1) {
-		len = tty_prepare_flip_string(port, &buf,
-				char_count);
-		if (!len)
-			break;
-
-		len = min_t(unsigned int, min(len, char_count),
-				rx_bufsize - new_rx_get);
-
-		memcpy_fromio(buf, cinfo->base_addr +
-				rx_bufaddr + new_rx_get, len);
-
-		new_rx_get = (new_rx_get + len) &
-				(rx_bufsize - 1);
-		char_count -= len;
-		info->icount.rx += len;
-		info->idle_stats.recv_bytes += len;
-	}
-#else
-	len = tty_buffer_request_room(port, char_count);
-	while (len--) {
-		data = readb(cinfo->base_addr + rx_bufaddr +
-				new_rx_get);
-		new_rx_get = (new_rx_get + 1) &
-					(rx_bufsize - 1);
-		tty_insert_flip_char(port, data, TTY_NORMAL);
-		info->idle_stats.recv_bytes++;
-		info->icount.rx++;
-	}
-#endif
-#ifdef CONFIG_CYZ_INTR
-	/* Recalculate the number of chars in the RX buffer and issue
-	   a cmd in case it's higher than the RX high water mark */
-	rx_put = readl(&buf_ctrl->rx_put);
-	if (rx_put >= rx_get)
-		char_count = rx_put - rx_get;
-	else
-		char_count = rx_put - rx_get + rx_bufsize;
-	if (char_count >= readl(&buf_ctrl->rx_threshold) &&
-			!timer_pending(&info->rx_full_timer))
-		mod_timer(&info->rx_full_timer, jiffies + 1);
-#endif
-	info->idle_stats.recv_idle = jiffies;
-	tty_schedule_flip(&info->port);
-
-	/* Update rx_get */
-	cy_writel(&buf_ctrl->rx_get, new_rx_get);
-}
-
-static void cyz_handle_tx(struct cyclades_port *info)
-{
-	struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl;
-	struct cyclades_card *cinfo = info->card;
-	struct tty_struct *tty;
-	u8 data;
-	unsigned int char_count;
-#ifdef BLOCKMOVE
-	int small_count;
-#endif
-	__u32 tx_put, tx_get, tx_bufsize, tx_bufaddr;
-
-	if (info->xmit_cnt <= 0)	/* Nothing to transmit */
-		return;
-
-	tx_get = readl(&buf_ctrl->tx_get);
-	tx_put = readl(&buf_ctrl->tx_put);
-	tx_bufsize = readl(&buf_ctrl->tx_bufsize);
-	tx_bufaddr = readl(&buf_ctrl->tx_bufaddr);
-	if (tx_put >= tx_get)
-		char_count = tx_get - tx_put - 1 + tx_bufsize;
-	else
-		char_count = tx_get - tx_put - 1;
-
-	if (!char_count)
-		return;
-		
-	tty = tty_port_tty_get(&info->port);
-	if (tty == NULL)
-		goto ztxdone;
-
-	if (info->x_char) {	/* send special char */
-		data = info->x_char;
-
-		cy_writeb(cinfo->base_addr + tx_bufaddr + tx_put, data);
-		tx_put = (tx_put + 1) & (tx_bufsize - 1);
-		info->x_char = 0;
-		char_count--;
-		info->icount.tx++;
-	}
-#ifdef BLOCKMOVE
-	while (0 < (small_count = min_t(unsigned int,
-			tx_bufsize - tx_put, min_t(unsigned int,
-				(SERIAL_XMIT_SIZE - info->xmit_tail),
-				min_t(unsigned int, info->xmit_cnt,
-					char_count))))) {
-
-		memcpy_toio((char *)(cinfo->base_addr + tx_bufaddr + tx_put),
-				&info->port.xmit_buf[info->xmit_tail],
-				small_count);
-
-		tx_put = (tx_put + small_count) & (tx_bufsize - 1);
-		char_count -= small_count;
-		info->icount.tx += small_count;
-		info->xmit_cnt -= small_count;
-		info->xmit_tail = (info->xmit_tail + small_count) &
-				(SERIAL_XMIT_SIZE - 1);
-	}
-#else
-	while (info->xmit_cnt && char_count) {
-		data = info->port.xmit_buf[info->xmit_tail];
-		info->xmit_cnt--;
-		info->xmit_tail = (info->xmit_tail + 1) &
-				(SERIAL_XMIT_SIZE - 1);
-
-		cy_writeb(cinfo->base_addr + tx_bufaddr + tx_put, data);
-		tx_put = (tx_put + 1) & (tx_bufsize - 1);
-		char_count--;
-		info->icount.tx++;
-	}
-#endif
-	tty_wakeup(tty);
-	tty_kref_put(tty);
-ztxdone:
-	/* Update tx_put */
-	cy_writel(&buf_ctrl->tx_put, tx_put);
-}
-
-static void cyz_handle_cmd(struct cyclades_card *cinfo)
-{
-	struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl;
-	struct cyclades_port *info;
-	__u32 channel, param, fw_ver;
-	__u8 cmd;
-	int special_count;
-	int delta_count;
-
-	fw_ver = readl(&board_ctrl->fw_version);
-
-	while (cyz_fetch_msg(cinfo, &channel, &cmd, &param) == 1) {
-		special_count = 0;
-		delta_count = 0;
-		info = &cinfo->ports[channel];
-
-		switch (cmd) {
-		case C_CM_PR_ERROR:
-			tty_insert_flip_char(&info->port, 0, TTY_PARITY);
-			info->icount.rx++;
-			special_count++;
-			break;
-		case C_CM_FR_ERROR:
-			tty_insert_flip_char(&info->port, 0, TTY_FRAME);
-			info->icount.rx++;
-			special_count++;
-			break;
-		case C_CM_RXBRK:
-			tty_insert_flip_char(&info->port, 0, TTY_BREAK);
-			info->icount.rx++;
-			special_count++;
-			break;
-		case C_CM_MDCD:
-			info->icount.dcd++;
-			delta_count++;
-			if (tty_port_check_carrier(&info->port)) {
-				u32 dcd = fw_ver > 241 ? param :
-					readl(&info->u.cyz.ch_ctrl->rs_status);
-				if (dcd & C_RS_DCD)
-					wake_up_interruptible(&info->port.open_wait);
-				else
-					tty_port_tty_hangup(&info->port, false);
-			}
-			break;
-		case C_CM_MCTS:
-			info->icount.cts++;
-			delta_count++;
-			break;
-		case C_CM_MRI:
-			info->icount.rng++;
-			delta_count++;
-			break;
-		case C_CM_MDSR:
-			info->icount.dsr++;
-			delta_count++;
-			break;
-#ifdef Z_WAKE
-		case C_CM_IOCTLW:
-			complete(&info->shutdown_wait);
-			break;
-#endif
-#ifdef CONFIG_CYZ_INTR
-		case C_CM_RXHIWM:
-		case C_CM_RXNNDT:
-		case C_CM_INTBACK2:
-			/* Reception Interrupt */
-#ifdef CY_DEBUG_INTERRUPTS
-			printk(KERN_DEBUG "cyz_interrupt: rcvd intr, card %d, "
-					"port %ld\n", info->card, channel);
-#endif
-			cyz_handle_rx(info);
-			break;
-		case C_CM_TXBEMPTY:
-		case C_CM_TXLOWWM:
-		case C_CM_INTBACK:
-			/* Transmission Interrupt */
-#ifdef CY_DEBUG_INTERRUPTS
-			printk(KERN_DEBUG "cyz_interrupt: xmit intr, card %d, "
-					"port %ld\n", info->card, channel);
-#endif
-			cyz_handle_tx(info);
-			break;
-#endif				/* CONFIG_CYZ_INTR */
-		case C_CM_FATAL:
-			/* should do something with this !!! */
-			break;
-		default:
-			break;
-		}
-		if (delta_count)
-			wake_up_interruptible(&info->port.delta_msr_wait);
-		if (special_count)
-			tty_schedule_flip(&info->port);
-	}
-}
-
-#ifdef CONFIG_CYZ_INTR
-static irqreturn_t cyz_interrupt(int irq, void *dev_id)
-{
-	struct cyclades_card *cinfo = dev_id;
-
-	if (unlikely(!cyz_is_loaded(cinfo))) {
-#ifdef CY_DEBUG_INTERRUPTS
-		printk(KERN_DEBUG "cyz_interrupt: board not yet loaded "
-				"(IRQ%d).\n", irq);
-#endif
-		return IRQ_NONE;
-	}
-
-	/* Handle the interrupts */
-	cyz_handle_cmd(cinfo);
-
-	return IRQ_HANDLED;
-}				/* cyz_interrupt */
-
-static void cyz_rx_restart(struct timer_list *t)
-{
-	struct cyclades_port *info = from_timer(info, t, rx_full_timer);
-	struct cyclades_card *card = info->card;
-	int retval;
-	__u32 channel = info->line - card->first_line;
-	unsigned long flags;
-
-	spin_lock_irqsave(&card->card_lock, flags);
-	retval = cyz_issue_cmd(card, channel, C_CM_INTBACK2, 0L);
-	if (retval != 0) {
-		printk(KERN_ERR "cyc:cyz_rx_restart retval on ttyC%d was %x\n",
-			info->line, retval);
-	}
-	spin_unlock_irqrestore(&card->card_lock, flags);
-}
-
-#else				/* CONFIG_CYZ_INTR */
-
-static void cyz_poll(struct timer_list *unused)
-{
-	struct cyclades_card *cinfo;
-	struct cyclades_port *info;
-	unsigned long expires = jiffies + HZ;
-	unsigned int port, card;
-
-	for (card = 0; card < NR_CARDS; card++) {
-		cinfo = &cy_card[card];
-
-		if (!cy_is_Z(cinfo))
-			continue;
-		if (!cyz_is_loaded(cinfo))
-			continue;
-
-	/* Skip first polling cycle to avoid racing conditions with the FW */
-		if (!cinfo->intr_enabled) {
-			cinfo->intr_enabled = 1;
-			continue;
-		}
-
-		cyz_handle_cmd(cinfo);
-
-		for (port = 0; port < cinfo->nports; port++) {
-			info = &cinfo->ports[port];
-
-			if (!info->throttle)
-				cyz_handle_rx(info);
-			cyz_handle_tx(info);
-		}
-		/* poll every 'cyz_polling_cycle' period */
-		expires = jiffies + cyz_polling_cycle;
-	}
-	mod_timer(&cyz_timerlist, expires);
-}				/* cyz_poll */
-
-#endif				/* CONFIG_CYZ_INTR */
-
-/********** End of block of Cyclades-Z specific code *********/
-/***********************************************************/
-
-/* This is called whenever a port becomes active;
-   interrupts are enabled and DTR & RTS are turned on.
- */
-static int cy_startup(struct cyclades_port *info, struct tty_struct *tty)
-{
-	struct cyclades_card *card;
-	unsigned long flags;
-	int retval = 0;
-	int channel;
-	unsigned long page;
-
-	card = info->card;
-	channel = info->line - card->first_line;
-
-	page = get_zeroed_page(GFP_KERNEL);
-	if (!page)
-		return -ENOMEM;
-
-	spin_lock_irqsave(&card->card_lock, flags);
-
-	if (tty_port_initialized(&info->port))
-		goto errout;
-
-	if (!info->type) {
-		set_bit(TTY_IO_ERROR, &tty->flags);
-		goto errout;
-	}
-
-	if (info->port.xmit_buf)
-		free_page(page);
-	else
-		info->port.xmit_buf = (unsigned char *)page;
-
-	spin_unlock_irqrestore(&card->card_lock, flags);
-
-	cy_set_line_char(info, tty);
-
-	if (!cy_is_Z(card)) {
-		channel &= 0x03;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-
-		cyy_writeb(info, CyCAR, channel);
-
-		cyy_writeb(info, CyRTPR,
-			(info->default_timeout ? info->default_timeout : 0x02));
-		/* 10ms rx timeout */
-
-		cyy_issue_cmd(info, CyCHAN_CTL | CyENB_RCVR | CyENB_XMTR);
-
-		cyy_change_rts_dtr(info, TIOCM_RTS | TIOCM_DTR, 0);
-
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyRxData);
-	} else {
-		struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
-
-		if (!cyz_is_loaded(card))
-			return -ENODEV;
-
-#ifdef CY_DEBUG_OPEN
-		printk(KERN_DEBUG "cyc startup Z card %d, channel %d, "
-			"base_addr %p\n", card, channel, card->base_addr);
-#endif
-		spin_lock_irqsave(&card->card_lock, flags);
-
-		cy_writel(&ch_ctrl->op_mode, C_CH_ENABLE);
-#ifdef Z_WAKE
-#ifdef CONFIG_CYZ_INTR
-		cy_writel(&ch_ctrl->intr_enable,
-			  C_IN_TXBEMPTY | C_IN_TXLOWWM | C_IN_RXHIWM |
-			  C_IN_RXNNDT | C_IN_IOCTLW | C_IN_MDCD);
-#else
-		cy_writel(&ch_ctrl->intr_enable,
-			  C_IN_IOCTLW | C_IN_MDCD);
-#endif				/* CONFIG_CYZ_INTR */
-#else
-#ifdef CONFIG_CYZ_INTR
-		cy_writel(&ch_ctrl->intr_enable,
-			  C_IN_TXBEMPTY | C_IN_TXLOWWM | C_IN_RXHIWM |
-			  C_IN_RXNNDT | C_IN_MDCD);
-#else
-		cy_writel(&ch_ctrl->intr_enable, C_IN_MDCD);
-#endif				/* CONFIG_CYZ_INTR */
-#endif				/* Z_WAKE */
-
-		retval = cyz_issue_cmd(card, channel, C_CM_IOCTL, 0L);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc:startup(1) retval on ttyC%d was "
-				"%x\n", info->line, retval);
-		}
-
-		/* Flush RX buffers before raising DTR and RTS */
-		retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_RX, 0L);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc:startup(2) retval on ttyC%d was "
-				"%x\n", info->line, retval);
-		}
-
-		/* set timeout !!! */
-		/* set RTS and DTR !!! */
-		tty_port_raise_dtr_rts(&info->port);
-
-		/* enable send, recv, modem !!! */
-	}
-
-	tty_port_set_initialized(&info->port, 1);
-
-	clear_bit(TTY_IO_ERROR, &tty->flags);
-	info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
-	info->breakon = info->breakoff = 0;
-	memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats));
-	info->idle_stats.in_use =
-	info->idle_stats.recv_idle =
-	info->idle_stats.xmit_idle = jiffies;
-
-	spin_unlock_irqrestore(&card->card_lock, flags);
-
-#ifdef CY_DEBUG_OPEN
-	printk(KERN_DEBUG "cyc startup done\n");
-#endif
-	return 0;
-
-errout:
-	spin_unlock_irqrestore(&card->card_lock, flags);
-	free_page(page);
-	return retval;
-}				/* startup */
-
-static void start_xmit(struct cyclades_port *info)
-{
-	struct cyclades_card *card = info->card;
-	unsigned long flags;
-	int channel = info->line - card->first_line;
-
-	if (!cy_is_Z(card)) {
-		spin_lock_irqsave(&card->card_lock, flags);
-		cyy_writeb(info, CyCAR, channel & 0x03);
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyTxRdy);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	} else {
-#ifdef CONFIG_CYZ_INTR
-		int retval;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-		retval = cyz_issue_cmd(card, channel, C_CM_INTBACK, 0L);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc:start_xmit retval on ttyC%d was "
-				"%x\n", info->line, retval);
-		}
-		spin_unlock_irqrestore(&card->card_lock, flags);
-#else				/* CONFIG_CYZ_INTR */
-		/* Don't have to do anything at this time */
-#endif				/* CONFIG_CYZ_INTR */
-	}
-}				/* start_xmit */
-
-/*
- * This routine shuts down a serial port; interrupts are disabled,
- * and DTR is dropped if the hangup on close termio flag is on.
- */
-static void cy_shutdown(struct cyclades_port *info, struct tty_struct *tty)
-{
-	struct cyclades_card *card;
-	unsigned long flags;
-
-	if (!tty_port_initialized(&info->port))
-		return;
-
-	card = info->card;
-	if (!cy_is_Z(card)) {
-		spin_lock_irqsave(&card->card_lock, flags);
-
-		/* Clear delta_msr_wait queue to avoid mem leaks. */
-		wake_up_interruptible(&info->port.delta_msr_wait);
-
-		if (info->port.xmit_buf) {
-			unsigned char *temp;
-			temp = info->port.xmit_buf;
-			info->port.xmit_buf = NULL;
-			free_page((unsigned long)temp);
-		}
-		if (C_HUPCL(tty))
-			cyy_change_rts_dtr(info, 0, TIOCM_RTS | TIOCM_DTR);
-
-		cyy_issue_cmd(info, CyCHAN_CTL | CyDIS_RCVR);
-		/* it may be appropriate to clear _XMIT at
-		   some later date (after testing)!!! */
-
-		set_bit(TTY_IO_ERROR, &tty->flags);
-		tty_port_set_initialized(&info->port, 0);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	} else {
-#ifdef CY_DEBUG_OPEN
-		int channel = info->line - card->first_line;
-		printk(KERN_DEBUG "cyc shutdown Z card %d, channel %d, "
-			"base_addr %p\n", card, channel, card->base_addr);
-#endif
-
-		if (!cyz_is_loaded(card))
-			return;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-
-		if (info->port.xmit_buf) {
-			unsigned char *temp;
-			temp = info->port.xmit_buf;
-			info->port.xmit_buf = NULL;
-			free_page((unsigned long)temp);
-		}
-
-		if (C_HUPCL(tty))
-			tty_port_lower_dtr_rts(&info->port);
-
-		set_bit(TTY_IO_ERROR, &tty->flags);
-		tty_port_set_initialized(&info->port, 0);
-
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	}
-
-#ifdef CY_DEBUG_OPEN
-	printk(KERN_DEBUG "cyc shutdown done\n");
-#endif
-}				/* shutdown */
-
-/*
- * ------------------------------------------------------------
- * cy_open() and friends
- * ------------------------------------------------------------
- */
-
-/*
- * This routine is called whenever a serial port is opened.  It
- * performs the serial-specific initialization for the tty structure.
- */
-static int cy_open(struct tty_struct *tty, struct file *filp)
-{
-	struct cyclades_port *info;
-	unsigned int i, line = tty->index;
-	int retval;
-
-	for (i = 0; i < NR_CARDS; i++)
-		if (line < cy_card[i].first_line + cy_card[i].nports &&
-				line >= cy_card[i].first_line)
-			break;
-	if (i >= NR_CARDS)
-		return -ENODEV;
-	info = &cy_card[i].ports[line - cy_card[i].first_line];
-	if (info->line < 0)
-		return -ENODEV;
-
-	/* If the card's firmware hasn't been loaded,
-	   treat it as absent from the system.  This
-	   will make the user pay attention.
-	 */
-	if (cy_is_Z(info->card)) {
-		struct cyclades_card *cinfo = info->card;
-		struct FIRM_ID __iomem *firm_id = cinfo->base_addr + ID_ADDRESS;
-
-		if (!cyz_is_loaded(cinfo)) {
-			if (cinfo->hw_ver == ZE_V1 && cyz_fpga_loaded(cinfo) &&
-					readl(&firm_id->signature) ==
-					ZFIRM_HLT) {
-				printk(KERN_ERR "cyc:Cyclades-Z Error: you "
-					"need an external power supply for "
-					"this number of ports.\nFirmware "
-					"halted.\n");
-			} else {
-				printk(KERN_ERR "cyc:Cyclades-Z firmware not "
-					"yet loaded\n");
-			}
-			return -ENODEV;
-		}
-#ifdef CONFIG_CYZ_INTR
-		else {
-		/* In case this Z board is operating in interrupt mode, its
-		   interrupts should be enabled as soon as the first open
-		   happens to one of its ports. */
-			if (!cinfo->intr_enabled) {
-				u16 intr;
-
-				/* Enable interrupts on the PLX chip */
-				intr = readw(&cinfo->ctl_addr.p9060->
-						intr_ctrl_stat) | 0x0900;
-				cy_writew(&cinfo->ctl_addr.p9060->
-						intr_ctrl_stat, intr);
-				/* Enable interrupts on the FW */
-				retval = cyz_issue_cmd(cinfo, 0,
-						C_CM_IRQ_ENBL, 0L);
-				if (retval != 0) {
-					printk(KERN_ERR "cyc:IRQ enable retval "
-						"was %x\n", retval);
-				}
-				cinfo->intr_enabled = 1;
-			}
-		}
-#endif				/* CONFIG_CYZ_INTR */
-		/* Make sure this Z port really exists in hardware */
-		if (info->line > (cinfo->first_line + cinfo->nports - 1))
-			return -ENODEV;
-	}
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_open ttyC%d\n", info->line);
-#endif
-	tty->driver_data = info;
-	if (serial_paranoia_check(info, tty->name, "cy_open"))
-		return -ENODEV;
-
-#ifdef CY_DEBUG_OPEN
-	printk(KERN_DEBUG "cyc:cy_open ttyC%d, count = %d\n", info->line,
-			info->port.count);
-#endif
-	info->port.count++;
-#ifdef CY_DEBUG_COUNT
-	printk(KERN_DEBUG "cyc:cy_open (%d): incrementing count to %d\n",
-		current->pid, info->port.count);
-#endif
-
-	/*
-	 * Start up serial port
-	 */
-	retval = cy_startup(info, tty);
-	if (retval)
-		return retval;
-
-	retval = tty_port_block_til_ready(&info->port, tty, filp);
-	if (retval) {
-#ifdef CY_DEBUG_OPEN
-		printk(KERN_DEBUG "cyc:cy_open returning after block_til_ready "
-			"with %d\n", retval);
-#endif
-		return retval;
-	}
-
-	info->throttle = 0;
-	tty_port_tty_set(&info->port, tty);
-
-#ifdef CY_DEBUG_OPEN
-	printk(KERN_DEBUG "cyc:cy_open done\n");
-#endif
-	return 0;
-}				/* cy_open */
-
-/*
- * cy_wait_until_sent() --- wait until the transmitter is empty
- */
-static void cy_wait_until_sent(struct tty_struct *tty, int timeout)
-{
-	struct cyclades_card *card;
-	struct cyclades_port *info = tty->driver_data;
-	unsigned long orig_jiffies;
-	int char_time;
-
-	if (serial_paranoia_check(info, tty->name, "cy_wait_until_sent"))
-		return;
-
-	if (info->xmit_fifo_size == 0)
-		return;		/* Just in case.... */
-
-	orig_jiffies = jiffies;
-	/*
-	 * Set the check interval to be 1/5 of the estimated time to
-	 * send a single character, and make it at least 1.  The check
-	 * interval should also be less than the timeout.
-	 *
-	 * Note: we have to use pretty tight timings here to satisfy
-	 * the NIST-PCTS.
-	 */
-	char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
-	char_time = char_time / 5;
-	if (char_time <= 0)
-		char_time = 1;
-	if (timeout < 0)
-		timeout = 0;
-	if (timeout)
-		char_time = min(char_time, timeout);
-	/*
-	 * If the transmitter hasn't cleared in twice the approximate
-	 * amount of time to send the entire FIFO, it probably won't
-	 * ever clear.  This assumes the UART isn't doing flow
-	 * control, which is currently the case.  Hence, if it ever
-	 * takes longer than info->timeout, this is probably due to a
-	 * UART bug of some kind.  So, we clamp the timeout parameter at
-	 * 2*info->timeout.
-	 */
-	if (!timeout || timeout > 2 * info->timeout)
-		timeout = 2 * info->timeout;
-
-	card = info->card;
-	if (!cy_is_Z(card)) {
-		while (cyy_readb(info, CySRER) & CyTxRdy) {
-			if (msleep_interruptible(jiffies_to_msecs(char_time)))
-				break;
-			if (timeout && time_after(jiffies, orig_jiffies +
-					timeout))
-				break;
-		}
-	}
-	/* Run one more char cycle */
-	msleep_interruptible(jiffies_to_msecs(char_time * 5));
-}
-
-static void cy_flush_buffer(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	int channel, retval;
-	unsigned long flags;
-
-#ifdef CY_DEBUG_IO
-	printk(KERN_DEBUG "cyc:cy_flush_buffer ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_flush_buffer"))
-		return;
-
-	card = info->card;
-	channel = info->line - card->first_line;
-
-	spin_lock_irqsave(&card->card_lock, flags);
-	info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
-	spin_unlock_irqrestore(&card->card_lock, flags);
-
-	if (cy_is_Z(card)) {	/* If it is a Z card, flush the on-board
-					   buffers as well */
-		spin_lock_irqsave(&card->card_lock, flags);
-		retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_TX, 0L);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc: flush_buffer retval on ttyC%d "
-				"was %x\n", info->line, retval);
-		}
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	}
-	tty_wakeup(tty);
-}				/* cy_flush_buffer */
-
-
-static void cy_do_close(struct tty_port *port)
-{
-	struct cyclades_port *info = container_of(port, struct cyclades_port,
-								port);
-	struct cyclades_card *card;
-	unsigned long flags;
-	int channel;
-
-	card = info->card;
-	channel = info->line - card->first_line;
-	spin_lock_irqsave(&card->card_lock, flags);
-
-	if (!cy_is_Z(card)) {
-		/* Stop accepting input */
-		cyy_writeb(info, CyCAR, channel & 0x03);
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyRxData);
-		if (tty_port_initialized(&info->port)) {
-			/* Waiting for on-board buffers to be empty before
-			   closing the port */
-			spin_unlock_irqrestore(&card->card_lock, flags);
-			cy_wait_until_sent(port->tty, info->timeout);
-			spin_lock_irqsave(&card->card_lock, flags);
-		}
-	} else {
-#ifdef Z_WAKE
-		/* Waiting for on-board buffers to be empty before closing
-		   the port */
-		struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
-		int retval;
-
-		if (readl(&ch_ctrl->flow_status) != C_FS_TXIDLE) {
-			retval = cyz_issue_cmd(card, channel, C_CM_IOCTLW, 0L);
-			if (retval != 0) {
-				printk(KERN_DEBUG "cyc:cy_close retval on "
-					"ttyC%d was %x\n", info->line, retval);
-			}
-			spin_unlock_irqrestore(&card->card_lock, flags);
-			wait_for_completion_interruptible(&info->shutdown_wait);
-			spin_lock_irqsave(&card->card_lock, flags);
-		}
-#endif
-	}
-	spin_unlock_irqrestore(&card->card_lock, flags);
-	cy_shutdown(info, port->tty);
-}
-
-/*
- * This routine is called when a particular tty device is closed.
- */
-static void cy_close(struct tty_struct *tty, struct file *filp)
-{
-	struct cyclades_port *info = tty->driver_data;
-	if (!info || serial_paranoia_check(info, tty->name, "cy_close"))
-		return;
-	tty_port_close(&info->port, tty, filp);
-}				/* cy_close */
-
-/* This routine gets called when tty_write has put something into
- * the write_queue.  The characters may come from user space or
- * kernel space.
- *
- * This routine will return the number of characters actually
- * accepted for writing.
- *
- * If the port is not already transmitting stuff, start it off by
- * enabling interrupts.  The interrupt service routine will then
- * ensure that the characters are sent.
- * If the port is already active, there is no need to kick it.
- *
- */
-static int cy_write(struct tty_struct *tty, const unsigned char *buf, int count)
-{
-	struct cyclades_port *info = tty->driver_data;
-	unsigned long flags;
-	int c, ret = 0;
-
-#ifdef CY_DEBUG_IO
-	printk(KERN_DEBUG "cyc:cy_write ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_write"))
-		return 0;
-
-	if (!info->port.xmit_buf)
-		return 0;
-
-	spin_lock_irqsave(&info->card->card_lock, flags);
-	while (1) {
-		c = min(count, (int)(SERIAL_XMIT_SIZE - info->xmit_cnt - 1));
-		c = min(c, (int)(SERIAL_XMIT_SIZE - info->xmit_head));
-
-		if (c <= 0)
-			break;
-
-		memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
-		info->xmit_head = (info->xmit_head + c) &
-			(SERIAL_XMIT_SIZE - 1);
-		info->xmit_cnt += c;
-		buf += c;
-		count -= c;
-		ret += c;
-	}
-	spin_unlock_irqrestore(&info->card->card_lock, flags);
-
-	info->idle_stats.xmit_bytes += ret;
-	info->idle_stats.xmit_idle = jiffies;
-
-	if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped)
-		start_xmit(info);
-
-	return ret;
-}				/* cy_write */
-
-/*
- * This routine is called by the kernel to write a single
- * character to the tty device.  If the kernel uses this routine,
- * it must call the flush_chars() routine (if defined) when it is
- * done stuffing characters into the driver.  If there is no room
- * in the queue, the character is ignored.
- */
-static int cy_put_char(struct tty_struct *tty, unsigned char ch)
-{
-	struct cyclades_port *info = tty->driver_data;
-	unsigned long flags;
-
-#ifdef CY_DEBUG_IO
-	printk(KERN_DEBUG "cyc:cy_put_char ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_put_char"))
-		return 0;
-
-	if (!info->port.xmit_buf)
-		return 0;
-
-	spin_lock_irqsave(&info->card->card_lock, flags);
-	if (info->xmit_cnt >= (int)(SERIAL_XMIT_SIZE - 1)) {
-		spin_unlock_irqrestore(&info->card->card_lock, flags);
-		return 0;
-	}
-
-	info->port.xmit_buf[info->xmit_head++] = ch;
-	info->xmit_head &= SERIAL_XMIT_SIZE - 1;
-	info->xmit_cnt++;
-	info->idle_stats.xmit_bytes++;
-	info->idle_stats.xmit_idle = jiffies;
-	spin_unlock_irqrestore(&info->card->card_lock, flags);
-	return 1;
-}				/* cy_put_char */
-
-/*
- * This routine is called by the kernel after it has written a
- * series of characters to the tty device using put_char().
- */
-static void cy_flush_chars(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-
-#ifdef CY_DEBUG_IO
-	printk(KERN_DEBUG "cyc:cy_flush_chars ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_flush_chars"))
-		return;
-
-	if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
-			!info->port.xmit_buf)
-		return;
-
-	start_xmit(info);
-}				/* cy_flush_chars */
-
-/*
- * This routine returns the numbers of characters the tty driver
- * will accept for queuing to be written.  This number is subject
- * to change as output buffers get emptied, or if the output flow
- * control is activated.
- */
-static int cy_write_room(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-	int ret;
-
-#ifdef CY_DEBUG_IO
-	printk(KERN_DEBUG "cyc:cy_write_room ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_write_room"))
-		return 0;
-	ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
-	if (ret < 0)
-		ret = 0;
-	return ret;
-}				/* cy_write_room */
-
-static int cy_chars_in_buffer(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-
-	if (serial_paranoia_check(info, tty->name, "cy_chars_in_buffer"))
-		return 0;
-
-#ifdef Z_EXT_CHARS_IN_BUFFER
-	if (!cy_is_Z(info->card)) {
-#endif				/* Z_EXT_CHARS_IN_BUFFER */
-#ifdef CY_DEBUG_IO
-		printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n",
-			info->line, info->xmit_cnt);
-#endif
-		return info->xmit_cnt;
-#ifdef Z_EXT_CHARS_IN_BUFFER
-	} else {
-		struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl;
-		int char_count;
-		__u32 tx_put, tx_get, tx_bufsize;
-
-		tx_get = readl(&buf_ctrl->tx_get);
-		tx_put = readl(&buf_ctrl->tx_put);
-		tx_bufsize = readl(&buf_ctrl->tx_bufsize);
-		if (tx_put >= tx_get)
-			char_count = tx_put - tx_get;
-		else
-			char_count = tx_put - tx_get + tx_bufsize;
-#ifdef CY_DEBUG_IO
-		printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n",
-			info->line, info->xmit_cnt + char_count);
-#endif
-		return info->xmit_cnt + char_count;
-	}
-#endif				/* Z_EXT_CHARS_IN_BUFFER */
-}				/* cy_chars_in_buffer */
-
-/*
- * ------------------------------------------------------------
- * cy_ioctl() and friends
- * ------------------------------------------------------------
- */
-
-static void cyy_baud_calc(struct cyclades_port *info, __u32 baud)
-{
-	int co, co_val, bpr;
-	__u32 cy_clock = ((info->chip_rev >= CD1400_REV_J) ? 60000000 :
-			25000000);
-
-	if (baud == 0) {
-		info->tbpr = info->tco = info->rbpr = info->rco = 0;
-		return;
-	}
-
-	/* determine which prescaler to use */
-	for (co = 4, co_val = 2048; co; co--, co_val >>= 2) {
-		if (cy_clock / co_val / baud > 63)
-			break;
-	}
-
-	bpr = (cy_clock / co_val * 2 / baud + 1) / 2;
-	if (bpr > 255)
-		bpr = 255;
-
-	info->tbpr = info->rbpr = bpr;
-	info->tco = info->rco = co;
-}
-
-/*
- * This routine finds or computes the various line characteristics.
- * It used to be called config_setup
- */
-static void cy_set_line_char(struct cyclades_port *info, struct tty_struct *tty)
-{
-	struct cyclades_card *card;
-	unsigned long flags;
-	int channel;
-	unsigned cflag, iflag;
-	int baud, baud_rate = 0;
-	int i;
-
-	if (info->line == -1)
-		return;
-
-	cflag = tty->termios.c_cflag;
-	iflag = tty->termios.c_iflag;
-
-	card = info->card;
-	channel = info->line - card->first_line;
-
-	if (!cy_is_Z(card)) {
-		u32 cflags;
-
-		/* baud rate */
-		baud = tty_get_baud_rate(tty);
-		if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
-				ASYNC_SPD_CUST) {
-			if (info->custom_divisor)
-				baud_rate = info->baud / info->custom_divisor;
-			else
-				baud_rate = info->baud;
-		} else if (baud > CD1400_MAX_SPEED) {
-			baud = CD1400_MAX_SPEED;
-		}
-		/* find the baud index */
-		for (i = 0; i < 20; i++) {
-			if (baud == baud_table[i])
-				break;
-		}
-		if (i == 20)
-			i = 19;	/* CD1400_MAX_SPEED */
-
-		if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
-				ASYNC_SPD_CUST) {
-			cyy_baud_calc(info, baud_rate);
-		} else {
-			if (info->chip_rev >= CD1400_REV_J) {
-				/* It is a CD1400 rev. J or later */
-				info->tbpr = baud_bpr_60[i];	/* Tx BPR */
-				info->tco = baud_co_60[i];	/* Tx CO */
-				info->rbpr = baud_bpr_60[i];	/* Rx BPR */
-				info->rco = baud_co_60[i];	/* Rx CO */
-			} else {
-				info->tbpr = baud_bpr_25[i];	/* Tx BPR */
-				info->tco = baud_co_25[i];	/* Tx CO */
-				info->rbpr = baud_bpr_25[i];	/* Rx BPR */
-				info->rco = baud_co_25[i];	/* Rx CO */
-			}
-		}
-		if (baud_table[i] == 134) {
-			/* get it right for 134.5 baud */
-			info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) +
-					2;
-		} else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
-				ASYNC_SPD_CUST) {
-			info->timeout = (info->xmit_fifo_size * HZ * 15 /
-					baud_rate) + 2;
-		} else if (baud_table[i]) {
-			info->timeout = (info->xmit_fifo_size * HZ * 15 /
-					baud_table[i]) + 2;
-			/* this needs to be propagated into the card info */
-		} else {
-			info->timeout = 0;
-		}
-		/* By tradition (is it a standard?) a baud rate of zero
-		   implies the line should be/has been closed.  A bit
-		   later in this routine such a test is performed. */
-
-		/* byte size and parity */
-		info->cor5 = 0;
-		info->cor4 = 0;
-		/* receive threshold */
-		info->cor3 = (info->default_threshold ?
-				info->default_threshold : baud_cor3[i]);
-		info->cor2 = CyETC;
-		switch (cflag & CSIZE) {
-		case CS5:
-			info->cor1 = Cy_5_BITS;
-			break;
-		case CS6:
-			info->cor1 = Cy_6_BITS;
-			break;
-		case CS7:
-			info->cor1 = Cy_7_BITS;
-			break;
-		case CS8:
-			info->cor1 = Cy_8_BITS;
-			break;
-		}
-		if (cflag & CSTOPB)
-			info->cor1 |= Cy_2_STOP;
-
-		if (cflag & PARENB) {
-			if (cflag & PARODD)
-				info->cor1 |= CyPARITY_O;
-			else
-				info->cor1 |= CyPARITY_E;
-		} else
-			info->cor1 |= CyPARITY_NONE;
-
-		/* CTS flow control flag */
-		tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
-		if (cflag & CRTSCTS)
-			info->cor2 |= CyCtsAE;
-		else
-			info->cor2 &= ~CyCtsAE;
-		tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
-
-	 /***********************************************
-	    The hardware option, CyRtsAO, presents RTS when
-	    the chip has characters to send.  Since most modems
-	    use RTS as reverse (inbound) flow control, this
-	    option is not used.  If inbound flow control is
-	    necessary, DTR can be programmed to provide the
-	    appropriate signals for use with a non-standard
-	    cable.  Contact Marcio Saito for details.
-	 ***********************************************/
-
-		channel &= 0x03;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-		cyy_writeb(info, CyCAR, channel);
-
-		/* tx and rx baud rate */
-
-		cyy_writeb(info, CyTCOR, info->tco);
-		cyy_writeb(info, CyTBPR, info->tbpr);
-		cyy_writeb(info, CyRCOR, info->rco);
-		cyy_writeb(info, CyRBPR, info->rbpr);
-
-		/* set line characteristics  according configuration */
-
-		cyy_writeb(info, CySCHR1, START_CHAR(tty));
-		cyy_writeb(info, CySCHR2, STOP_CHAR(tty));
-		cyy_writeb(info, CyCOR1, info->cor1);
-		cyy_writeb(info, CyCOR2, info->cor2);
-		cyy_writeb(info, CyCOR3, info->cor3);
-		cyy_writeb(info, CyCOR4, info->cor4);
-		cyy_writeb(info, CyCOR5, info->cor5);
-
-		cyy_issue_cmd(info, CyCOR_CHANGE | CyCOR1ch | CyCOR2ch |
-				CyCOR3ch);
-
-		/* !!! Is this needed? */
-		cyy_writeb(info, CyCAR, channel);
-		cyy_writeb(info, CyRTPR,
-			(info->default_timeout ? info->default_timeout : 0x02));
-		/* 10ms rx timeout */
-
-		cflags = CyCTS;
-		if (!C_CLOCAL(tty))
-			cflags |= CyDSR | CyRI | CyDCD;
-		/* without modem intr */
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyMdmCh);
-		/* act on 1->0 modem transitions */
-		if ((cflag & CRTSCTS) && info->rflow)
-			cyy_writeb(info, CyMCOR1, cflags | rflow_thr[i]);
-		else
-			cyy_writeb(info, CyMCOR1, cflags);
-		/* act on 0->1 modem transitions */
-		cyy_writeb(info, CyMCOR2, cflags);
-
-		if (i == 0)	/* baud rate is zero, turn off line */
-			cyy_change_rts_dtr(info, 0, TIOCM_DTR);
-		else
-			cyy_change_rts_dtr(info, TIOCM_DTR, 0);
-
-		clear_bit(TTY_IO_ERROR, &tty->flags);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-
-	} else {
-		struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
-		__u32 sw_flow;
-		int retval;
-
-		if (!cyz_is_loaded(card))
-			return;
-
-		/* baud rate */
-		baud = tty_get_baud_rate(tty);
-		if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
-				ASYNC_SPD_CUST) {
-			if (info->custom_divisor)
-				baud_rate = info->baud / info->custom_divisor;
-			else
-				baud_rate = info->baud;
-		} else if (baud > CYZ_MAX_SPEED) {
-			baud = CYZ_MAX_SPEED;
-		}
-		cy_writel(&ch_ctrl->comm_baud, baud);
-
-		if (baud == 134) {
-			/* get it right for 134.5 baud */
-			info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) +
-					2;
-		} else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
-				ASYNC_SPD_CUST) {
-			info->timeout = (info->xmit_fifo_size * HZ * 15 /
-					baud_rate) + 2;
-		} else if (baud) {
-			info->timeout = (info->xmit_fifo_size * HZ * 15 /
-					baud) + 2;
-			/* this needs to be propagated into the card info */
-		} else {
-			info->timeout = 0;
-		}
-
-		/* byte size and parity */
-		switch (cflag & CSIZE) {
-		case CS5:
-			cy_writel(&ch_ctrl->comm_data_l, C_DL_CS5);
-			break;
-		case CS6:
-			cy_writel(&ch_ctrl->comm_data_l, C_DL_CS6);
-			break;
-		case CS7:
-			cy_writel(&ch_ctrl->comm_data_l, C_DL_CS7);
-			break;
-		case CS8:
-			cy_writel(&ch_ctrl->comm_data_l, C_DL_CS8);
-			break;
-		}
-		if (cflag & CSTOPB) {
-			cy_writel(&ch_ctrl->comm_data_l,
-				  readl(&ch_ctrl->comm_data_l) | C_DL_2STOP);
-		} else {
-			cy_writel(&ch_ctrl->comm_data_l,
-				  readl(&ch_ctrl->comm_data_l) | C_DL_1STOP);
-		}
-		if (cflag & PARENB) {
-			if (cflag & PARODD)
-				cy_writel(&ch_ctrl->comm_parity, C_PR_ODD);
-			else
-				cy_writel(&ch_ctrl->comm_parity, C_PR_EVEN);
-		} else
-			cy_writel(&ch_ctrl->comm_parity, C_PR_NONE);
-
-		/* CTS flow control flag */
-		if (cflag & CRTSCTS) {
-			cy_writel(&ch_ctrl->hw_flow,
-				readl(&ch_ctrl->hw_flow) | C_RS_CTS | C_RS_RTS);
-		} else {
-			cy_writel(&ch_ctrl->hw_flow, readl(&ch_ctrl->hw_flow) &
-					~(C_RS_CTS | C_RS_RTS));
-		}
-		/* As the HW flow control is done in firmware, the driver
-		   doesn't need to care about it */
-		tty_port_set_cts_flow(&info->port, 0);
-
-		/* XON/XOFF/XANY flow control flags */
-		sw_flow = 0;
-		if (iflag & IXON) {
-			sw_flow |= C_FL_OXX;
-			if (iflag & IXANY)
-				sw_flow |= C_FL_OIXANY;
-		}
-		cy_writel(&ch_ctrl->sw_flow, sw_flow);
-
-		retval = cyz_issue_cmd(card, channel, C_CM_IOCTL, 0L);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc:set_line_char retval on ttyC%d "
-				"was %x\n", info->line, retval);
-		}
-
-		/* CD sensitivity */
-		tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
-
-		if (baud == 0) {	/* baud rate is zero, turn off line */
-			cy_writel(&ch_ctrl->rs_control,
-				  readl(&ch_ctrl->rs_control) & ~C_RS_DTR);
-#ifdef CY_DEBUG_DTR
-			printk(KERN_DEBUG "cyc:set_line_char dropping Z DTR\n");
-#endif
-		} else {
-			cy_writel(&ch_ctrl->rs_control,
-				  readl(&ch_ctrl->rs_control) | C_RS_DTR);
-#ifdef CY_DEBUG_DTR
-			printk(KERN_DEBUG "cyc:set_line_char raising Z DTR\n");
-#endif
-		}
-
-		retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc:set_line_char(2) retval on ttyC%d "
-				"was %x\n", info->line, retval);
-		}
-
-		clear_bit(TTY_IO_ERROR, &tty->flags);
-	}
-}				/* set_line_char */
-
-static int cy_get_serial_info(struct tty_struct *tty,
-				struct serial_struct *ss)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *cinfo = info->card;
-
-	if (serial_paranoia_check(info, tty->name, "cy_ioctl"))
-		return -ENODEV;
-	ss->type = info->type;
-	ss->line = info->line;
-	ss->port = (info->card - cy_card) * 0x100 + info->line -
-			cinfo->first_line;
-	ss->irq = cinfo->irq;
-	ss->flags = info->port.flags;
-	ss->close_delay = info->port.close_delay;
-	ss->closing_wait = info->port.closing_wait;
-	ss->baud_base = info->baud;
-	ss->custom_divisor = info->custom_divisor;
-	return 0;
-}
-
-static int cy_set_serial_info(struct tty_struct *tty,
-				struct serial_struct *ss)
-{
-	struct cyclades_port *info = tty->driver_data;
-	int old_flags;
-	int ret;
-
-	if (serial_paranoia_check(info, tty->name, "cy_ioctl"))
-		return -ENODEV;
-
-	mutex_lock(&info->port.mutex);
-
-	old_flags = info->port.flags;
-
-	if (!capable(CAP_SYS_ADMIN)) {
-		if (ss->close_delay != info->port.close_delay ||
-				ss->baud_base != info->baud ||
-				(ss->flags & ASYNC_FLAGS &
-					~ASYNC_USR_MASK) !=
-				(info->port.flags & ASYNC_FLAGS & ~ASYNC_USR_MASK))
-		{
-			mutex_unlock(&info->port.mutex);
-			return -EPERM;
-		}
-		info->port.flags = (info->port.flags & ~ASYNC_USR_MASK) |
-				(ss->flags & ASYNC_USR_MASK);
-		info->baud = ss->baud_base;
-		info->custom_divisor = ss->custom_divisor;
-		goto check_and_exit;
-	}
-
-	/*
-	 * OK, past this point, all the error checking has been done.
-	 * At this point, we start making changes.....
-	 */
-
-	info->baud = ss->baud_base;
-	info->custom_divisor = ss->custom_divisor;
-	info->port.flags = (info->port.flags & ~ASYNC_FLAGS) |
-			(ss->flags & ASYNC_FLAGS);
-	info->port.close_delay = ss->close_delay * HZ / 100;
-	info->port.closing_wait = ss->closing_wait * HZ / 100;
-
-check_and_exit:
-	if (tty_port_initialized(&info->port)) {
-		if ((ss->flags ^ old_flags) & ASYNC_SPD_MASK) {
-			/* warn about deprecation unless clearing */
-			if (ss->flags & ASYNC_SPD_MASK)
-				dev_warn_ratelimited(tty->dev, "use of SPD flags is deprecated\n");
-		}
-		cy_set_line_char(info, tty);
-		ret = 0;
-	} else {
-		ret = cy_startup(info, tty);
-	}
-	mutex_unlock(&info->port.mutex);
-	return ret;
-}				/* set_serial_info */
-
-/*
- * get_lsr_info - get line status register info
- *
- * Purpose: Let user call ioctl() to get info when the UART physically
- *	    is emptied.  On bus types like RS485, the transmitter must
- *	    release the bus after transmitting. This must be done when
- *	    the transmit shift register is empty, not be done when the
- *	    transmit holding register is empty.  This functionality
- *	    allows an RS485 driver to be written in user space.
- */
-static int get_lsr_info(struct cyclades_port *info, unsigned int __user *value)
-{
-	struct cyclades_card *card = info->card;
-	unsigned int result;
-	unsigned long flags;
-	u8 status;
-
-	if (!cy_is_Z(card)) {
-		spin_lock_irqsave(&card->card_lock, flags);
-		status = cyy_readb(info, CySRER) & (CyTxRdy | CyTxMpty);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-		result = (status ? 0 : TIOCSER_TEMT);
-	} else {
-		/* Not supported yet */
-		return -EINVAL;
-	}
-	return put_user(result, value);
-}
-
-static int cy_tiocmget(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	int result;
-
-	if (serial_paranoia_check(info, tty->name, __func__))
-		return -ENODEV;
-
-	card = info->card;
-
-	if (!cy_is_Z(card)) {
-		unsigned long flags;
-		int channel = info->line - card->first_line;
-		u8 status;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-		cyy_writeb(info, CyCAR, channel & 0x03);
-		status = cyy_readb(info, CyMSVR1);
-		status |= cyy_readb(info, CyMSVR2);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-
-		if (info->rtsdtr_inv) {
-			result = ((status & CyRTS) ? TIOCM_DTR : 0) |
-				((status & CyDTR) ? TIOCM_RTS : 0);
-		} else {
-			result = ((status & CyRTS) ? TIOCM_RTS : 0) |
-				((status & CyDTR) ? TIOCM_DTR : 0);
-		}
-		result |= ((status & CyDCD) ? TIOCM_CAR : 0) |
-			((status & CyRI) ? TIOCM_RNG : 0) |
-			((status & CyDSR) ? TIOCM_DSR : 0) |
-			((status & CyCTS) ? TIOCM_CTS : 0);
-	} else {
-		u32 lstatus;
-
-		if (!cyz_is_loaded(card)) {
-			result = -ENODEV;
-			goto end;
-		}
-
-		lstatus = readl(&info->u.cyz.ch_ctrl->rs_status);
-		result = ((lstatus & C_RS_RTS) ? TIOCM_RTS : 0) |
-			((lstatus & C_RS_DTR) ? TIOCM_DTR : 0) |
-			((lstatus & C_RS_DCD) ? TIOCM_CAR : 0) |
-			((lstatus & C_RS_RI) ? TIOCM_RNG : 0) |
-			((lstatus & C_RS_DSR) ? TIOCM_DSR : 0) |
-			((lstatus & C_RS_CTS) ? TIOCM_CTS : 0);
-	}
-end:
-	return result;
-}				/* cy_tiomget */
-
-static int
-cy_tiocmset(struct tty_struct *tty,
-		unsigned int set, unsigned int clear)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	unsigned long flags;
-
-	if (serial_paranoia_check(info, tty->name, __func__))
-		return -ENODEV;
-
-	card = info->card;
-	if (!cy_is_Z(card)) {
-		spin_lock_irqsave(&card->card_lock, flags);
-		cyy_change_rts_dtr(info, set, clear);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	} else {
-		struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
-		int retval, channel = info->line - card->first_line;
-		u32 rs;
-
-		if (!cyz_is_loaded(card))
-			return -ENODEV;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-		rs = readl(&ch_ctrl->rs_control);
-		if (set & TIOCM_RTS)
-			rs |= C_RS_RTS;
-		if (clear & TIOCM_RTS)
-			rs &= ~C_RS_RTS;
-		if (set & TIOCM_DTR) {
-			rs |= C_RS_DTR;
-#ifdef CY_DEBUG_DTR
-			printk(KERN_DEBUG "cyc:set_modem_info raising Z DTR\n");
-#endif
-		}
-		if (clear & TIOCM_DTR) {
-			rs &= ~C_RS_DTR;
-#ifdef CY_DEBUG_DTR
-			printk(KERN_DEBUG "cyc:set_modem_info clearing "
-				"Z DTR\n");
-#endif
-		}
-		cy_writel(&ch_ctrl->rs_control, rs);
-		retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-		if (retval != 0) {
-			printk(KERN_ERR "cyc:set_modem_info retval on ttyC%d "
-				"was %x\n", info->line, retval);
-		}
-	}
-	return 0;
-}
-
-/*
- * cy_break() --- routine which turns the break handling on or off
- */
-static int cy_break(struct tty_struct *tty, int break_state)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	unsigned long flags;
-	int retval = 0;
-
-	if (serial_paranoia_check(info, tty->name, "cy_break"))
-		return -EINVAL;
-
-	card = info->card;
-
-	spin_lock_irqsave(&card->card_lock, flags);
-	if (!cy_is_Z(card)) {
-		/* Let the transmit ISR take care of this (since it
-		   requires stuffing characters into the output stream).
-		 */
-		if (break_state == -1) {
-			if (!info->breakon) {
-				info->breakon = 1;
-				if (!info->xmit_cnt) {
-					spin_unlock_irqrestore(&card->card_lock, flags);
-					start_xmit(info);
-					spin_lock_irqsave(&card->card_lock, flags);
-				}
-			}
-		} else {
-			if (!info->breakoff) {
-				info->breakoff = 1;
-				if (!info->xmit_cnt) {
-					spin_unlock_irqrestore(&card->card_lock, flags);
-					start_xmit(info);
-					spin_lock_irqsave(&card->card_lock, flags);
-				}
-			}
-		}
-	} else {
-		if (break_state == -1) {
-			retval = cyz_issue_cmd(card,
-				info->line - card->first_line,
-				C_CM_SET_BREAK, 0L);
-			if (retval != 0) {
-				printk(KERN_ERR "cyc:cy_break (set) retval on "
-					"ttyC%d was %x\n", info->line, retval);
-			}
-		} else {
-			retval = cyz_issue_cmd(card,
-				info->line - card->first_line,
-				C_CM_CLR_BREAK, 0L);
-			if (retval != 0) {
-				printk(KERN_DEBUG "cyc:cy_break (clr) retval "
-					"on ttyC%d was %x\n", info->line,
-					retval);
-			}
-		}
-	}
-	spin_unlock_irqrestore(&card->card_lock, flags);
-	return retval;
-}				/* cy_break */
-
-static int set_threshold(struct cyclades_port *info, unsigned long value)
-{
-	struct cyclades_card *card = info->card;
-	unsigned long flags;
-
-	if (!cy_is_Z(card)) {
-		info->cor3 &= ~CyREC_FIFO;
-		info->cor3 |= value & CyREC_FIFO;
-
-		spin_lock_irqsave(&card->card_lock, flags);
-		cyy_writeb(info, CyCOR3, info->cor3);
-		cyy_issue_cmd(info, CyCOR_CHANGE | CyCOR3ch);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	}
-	return 0;
-}				/* set_threshold */
-
-static int get_threshold(struct cyclades_port *info,
-						unsigned long __user *value)
-{
-	struct cyclades_card *card = info->card;
-
-	if (!cy_is_Z(card)) {
-		u8 tmp = cyy_readb(info, CyCOR3) & CyREC_FIFO;
-		return put_user(tmp, value);
-	}
-	return 0;
-}				/* get_threshold */
-
-static int set_timeout(struct cyclades_port *info, unsigned long value)
-{
-	struct cyclades_card *card = info->card;
-	unsigned long flags;
-
-	if (!cy_is_Z(card)) {
-		spin_lock_irqsave(&card->card_lock, flags);
-		cyy_writeb(info, CyRTPR, value & 0xff);
-		spin_unlock_irqrestore(&card->card_lock, flags);
-	}
-	return 0;
-}				/* set_timeout */
-
-static int get_timeout(struct cyclades_port *info,
-						unsigned long __user *value)
-{
-	struct cyclades_card *card = info->card;
-
-	if (!cy_is_Z(card)) {
-		u8 tmp = cyy_readb(info, CyRTPR);
-		return put_user(tmp, value);
-	}
-	return 0;
-}				/* get_timeout */
-
-static int cy_cflags_changed(struct cyclades_port *info, unsigned long arg,
-		struct cyclades_icount *cprev)
-{
-	struct cyclades_icount cnow;
-	unsigned long flags;
-	int ret;
-
-	spin_lock_irqsave(&info->card->card_lock, flags);
-	cnow = info->icount;	/* atomic copy */
-	spin_unlock_irqrestore(&info->card->card_lock, flags);
-
-	ret =	((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
-		((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
-		((arg & TIOCM_CD)  && (cnow.dcd != cprev->dcd)) ||
-		((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
-
-	*cprev = cnow;
-
-	return ret;
-}
-
-/*
- * This routine allows the tty driver to implement device-
- * specific ioctl's.  If the ioctl number passed in cmd is
- * not recognized by the driver, it should return ENOIOCTLCMD.
- */
-static int
-cy_ioctl(struct tty_struct *tty,
-	 unsigned int cmd, unsigned long arg)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_icount cnow;	/* kernel counter temps */
-	int ret_val = 0;
-	unsigned long flags;
-	void __user *argp = (void __user *)arg;
-
-	if (serial_paranoia_check(info, tty->name, "cy_ioctl"))
-		return -ENODEV;
-
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_ioctl ttyC%d, cmd = %x arg = %lx\n",
-		info->line, cmd, arg);
-#endif
-
-	switch (cmd) {
-	case CYGETMON:
-		if (copy_to_user(argp, &info->mon, sizeof(info->mon))) {
-			ret_val = -EFAULT;
-			break;
-		}
-		memset(&info->mon, 0, sizeof(info->mon));
-		break;
-	case CYGETTHRESH:
-		ret_val = get_threshold(info, argp);
-		break;
-	case CYSETTHRESH:
-		ret_val = set_threshold(info, arg);
-		break;
-	case CYGETDEFTHRESH:
-		ret_val = put_user(info->default_threshold,
-				(unsigned long __user *)argp);
-		break;
-	case CYSETDEFTHRESH:
-		info->default_threshold = arg & 0x0f;
-		break;
-	case CYGETTIMEOUT:
-		ret_val = get_timeout(info, argp);
-		break;
-	case CYSETTIMEOUT:
-		ret_val = set_timeout(info, arg);
-		break;
-	case CYGETDEFTIMEOUT:
-		ret_val = put_user(info->default_timeout,
-				(unsigned long __user *)argp);
-		break;
-	case CYSETDEFTIMEOUT:
-		info->default_timeout = arg & 0xff;
-		break;
-	case CYSETRFLOW:
-		info->rflow = (int)arg;
-		break;
-	case CYGETRFLOW:
-		ret_val = info->rflow;
-		break;
-	case CYSETRTSDTR_INV:
-		info->rtsdtr_inv = (int)arg;
-		break;
-	case CYGETRTSDTR_INV:
-		ret_val = info->rtsdtr_inv;
-		break;
-	case CYGETCD1400VER:
-		ret_val = info->chip_rev;
-		break;
-#ifndef CONFIG_CYZ_INTR
-	case CYZSETPOLLCYCLE:
-		if (arg > LONG_MAX / HZ)
-			return -ENODEV;
-		cyz_polling_cycle = (arg * HZ) / 1000;
-		break;
-	case CYZGETPOLLCYCLE:
-		ret_val = (cyz_polling_cycle * 1000) / HZ;
-		break;
-#endif				/* CONFIG_CYZ_INTR */
-	case CYSETWAIT:
-		info->port.closing_wait = (unsigned short)arg * HZ / 100;
-		break;
-	case CYGETWAIT:
-		ret_val = info->port.closing_wait / (HZ / 100);
-		break;
-	case TIOCSERGETLSR:	/* Get line status register */
-		ret_val = get_lsr_info(info, argp);
-		break;
-		/*
-		 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
-		 * - mask passed in arg for lines of interest
-		 *   (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
-		 * Caller should use TIOCGICOUNT to see which one it was
-		 */
-	case TIOCMIWAIT:
-		spin_lock_irqsave(&info->card->card_lock, flags);
-		/* note the counters on entry */
-		cnow = info->icount;
-		spin_unlock_irqrestore(&info->card->card_lock, flags);
-		ret_val = wait_event_interruptible(info->port.delta_msr_wait,
-				cy_cflags_changed(info, arg, &cnow));
-		break;
-
-		/*
-		 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
-		 * Return: write counters to the user passed counter struct
-		 * NB: both 1->0 and 0->1 transitions are counted except for
-		 *     RI where only 0->1 is counted.
-		 */
-	default:
-		ret_val = -ENOIOCTLCMD;
-	}
-
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_ioctl done\n");
-#endif
-	return ret_val;
-}				/* cy_ioctl */
-
-static int cy_get_icount(struct tty_struct *tty,
-				struct serial_icounter_struct *sic)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_icount cnow;	/* Used to snapshot */
-	unsigned long flags;
-
-	spin_lock_irqsave(&info->card->card_lock, flags);
-	cnow = info->icount;
-	spin_unlock_irqrestore(&info->card->card_lock, flags);
-
-	sic->cts = cnow.cts;
-	sic->dsr = cnow.dsr;
-	sic->rng = cnow.rng;
-	sic->dcd = cnow.dcd;
-	sic->rx = cnow.rx;
-	sic->tx = cnow.tx;
-	sic->frame = cnow.frame;
-	sic->overrun = cnow.overrun;
-	sic->parity = cnow.parity;
-	sic->brk = cnow.brk;
-	sic->buf_overrun = cnow.buf_overrun;
-	return 0;
-}
-
-/*
- * This routine allows the tty driver to be notified when
- * device's termios settings have changed.  Note that a
- * well-designed tty driver should be prepared to accept the case
- * where old == NULL, and try to do something rational.
- */
-static void cy_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
-{
-	struct cyclades_port *info = tty->driver_data;
-
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_set_termios ttyC%d\n", info->line);
-#endif
-
-	cy_set_line_char(info, tty);
-
-	if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
-		tty->hw_stopped = 0;
-		cy_start(tty);
-	}
-#if 0
-	/*
-	 * No need to wake up processes in open wait, since they
-	 * sample the CLOCAL flag once, and don't recheck it.
-	 * XXX  It's not clear whether the current behavior is correct
-	 * or not.  Hence, this may change.....
-	 */
-	if (!(old_termios->c_cflag & CLOCAL) && C_CLOCAL(tty))
-		wake_up_interruptible(&info->port.open_wait);
-#endif
-}				/* cy_set_termios */
-
-/* This function is used to send a high-priority XON/XOFF character to
-   the device.
-*/
-static void cy_send_xchar(struct tty_struct *tty, char ch)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	int channel;
-
-	if (serial_paranoia_check(info, tty->name, "cy_send_xchar"))
-		return;
-
-	info->x_char = ch;
-
-	if (ch)
-		cy_start(tty);
-
-	card = info->card;
-	channel = info->line - card->first_line;
-
-	if (cy_is_Z(card)) {
-		if (ch == STOP_CHAR(tty))
-			cyz_issue_cmd(card, channel, C_CM_SENDXOFF, 0L);
-		else if (ch == START_CHAR(tty))
-			cyz_issue_cmd(card, channel, C_CM_SENDXON, 0L);
-	}
-}
-
-/* This routine is called by the upper-layer tty layer to signal
-   that incoming characters should be throttled because the input
-   buffers are close to full.
- */
-static void cy_throttle(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	unsigned long flags;
-
-#ifdef CY_DEBUG_THROTTLE
-	printk(KERN_DEBUG "cyc:throttle %s ...ttyC%d\n", tty_name(tty),
-			 info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_throttle"))
-		return;
-
-	card = info->card;
-
-	if (I_IXOFF(tty)) {
-		if (!cy_is_Z(card))
-			cy_send_xchar(tty, STOP_CHAR(tty));
-		else
-			info->throttle = 1;
-	}
-
-	if (C_CRTSCTS(tty)) {
-		if (!cy_is_Z(card)) {
-			spin_lock_irqsave(&card->card_lock, flags);
-			cyy_change_rts_dtr(info, 0, TIOCM_RTS);
-			spin_unlock_irqrestore(&card->card_lock, flags);
-		} else {
-			info->throttle = 1;
-		}
-	}
-}				/* cy_throttle */
-
-/*
- * This routine notifies the tty driver that it should signal
- * that characters can now be sent to the tty without fear of
- * overrunning the input buffers of the line disciplines.
- */
-static void cy_unthrottle(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-	struct cyclades_card *card;
-	unsigned long flags;
-
-#ifdef CY_DEBUG_THROTTLE
-	printk(KERN_DEBUG "cyc:unthrottle %s ...ttyC%d\n",
-		tty_name(tty), info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_unthrottle"))
-		return;
-
-	if (I_IXOFF(tty)) {
-		if (info->x_char)
-			info->x_char = 0;
-		else
-			cy_send_xchar(tty, START_CHAR(tty));
-	}
-
-	if (C_CRTSCTS(tty)) {
-		card = info->card;
-		if (!cy_is_Z(card)) {
-			spin_lock_irqsave(&card->card_lock, flags);
-			cyy_change_rts_dtr(info, TIOCM_RTS, 0);
-			spin_unlock_irqrestore(&card->card_lock, flags);
-		} else {
-			info->throttle = 0;
-		}
-	}
-}				/* cy_unthrottle */
-
-/* cy_start and cy_stop provide software output flow control as a
-   function of XON/XOFF, software CTS, and other such stuff.
-*/
-static void cy_stop(struct tty_struct *tty)
-{
-	struct cyclades_card *cinfo;
-	struct cyclades_port *info = tty->driver_data;
-	int channel;
-	unsigned long flags;
-
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_stop ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_stop"))
-		return;
-
-	cinfo = info->card;
-	channel = info->line - cinfo->first_line;
-	if (!cy_is_Z(cinfo)) {
-		spin_lock_irqsave(&cinfo->card_lock, flags);
-		cyy_writeb(info, CyCAR, channel & 0x03);
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyTxRdy);
-		spin_unlock_irqrestore(&cinfo->card_lock, flags);
-	}
-}				/* cy_stop */
-
-static void cy_start(struct tty_struct *tty)
-{
-	struct cyclades_card *cinfo;
-	struct cyclades_port *info = tty->driver_data;
-	int channel;
-	unsigned long flags;
-
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_start ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_start"))
-		return;
-
-	cinfo = info->card;
-	channel = info->line - cinfo->first_line;
-	if (!cy_is_Z(cinfo)) {
-		spin_lock_irqsave(&cinfo->card_lock, flags);
-		cyy_writeb(info, CyCAR, channel & 0x03);
-		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyTxRdy);
-		spin_unlock_irqrestore(&cinfo->card_lock, flags);
-	}
-}				/* cy_start */
-
-/*
- * cy_hangup() --- called by tty_hangup() when a hangup is signaled.
- */
-static void cy_hangup(struct tty_struct *tty)
-{
-	struct cyclades_port *info = tty->driver_data;
-
-#ifdef CY_DEBUG_OTHER
-	printk(KERN_DEBUG "cyc:cy_hangup ttyC%d\n", info->line);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "cy_hangup"))
-		return;
-
-	cy_flush_buffer(tty);
-	cy_shutdown(info, tty);
-	tty_port_hangup(&info->port);
-}				/* cy_hangup */
-
-static int cyy_carrier_raised(struct tty_port *port)
-{
-	struct cyclades_port *info = container_of(port, struct cyclades_port,
-			port);
-	struct cyclades_card *cinfo = info->card;
-	unsigned long flags;
-	int channel = info->line - cinfo->first_line;
-	u32 cd;
-
-	spin_lock_irqsave(&cinfo->card_lock, flags);
-	cyy_writeb(info, CyCAR, channel & 0x03);
-	cd = cyy_readb(info, CyMSVR1) & CyDCD;
-	spin_unlock_irqrestore(&cinfo->card_lock, flags);
-
-	return cd;
-}
-
-static void cyy_dtr_rts(struct tty_port *port, int raise)
-{
-	struct cyclades_port *info = container_of(port, struct cyclades_port,
-			port);
-	struct cyclades_card *cinfo = info->card;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cinfo->card_lock, flags);
-	cyy_change_rts_dtr(info, raise ? TIOCM_RTS | TIOCM_DTR : 0,
-			raise ? 0 : TIOCM_RTS | TIOCM_DTR);
-	spin_unlock_irqrestore(&cinfo->card_lock, flags);
-}
-
-static int cyz_carrier_raised(struct tty_port *port)
-{
-	struct cyclades_port *info = container_of(port, struct cyclades_port,
-			port);
-
-	return readl(&info->u.cyz.ch_ctrl->rs_status) & C_RS_DCD;
-}
-
-static void cyz_dtr_rts(struct tty_port *port, int raise)
-{
-	struct cyclades_port *info = container_of(port, struct cyclades_port,
-			port);
-	struct cyclades_card *cinfo = info->card;
-	struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
-	int ret, channel = info->line - cinfo->first_line;
-	u32 rs;
-
-	rs = readl(&ch_ctrl->rs_control);
-	if (raise)
-		rs |= C_RS_RTS | C_RS_DTR;
-	else
-		rs &= ~(C_RS_RTS | C_RS_DTR);
-	cy_writel(&ch_ctrl->rs_control, rs);
-	ret = cyz_issue_cmd(cinfo, channel, C_CM_IOCTLM, 0L);
-	if (ret != 0)
-		printk(KERN_ERR "%s: retval on ttyC%d was %x\n",
-				__func__, info->line, ret);
-#ifdef CY_DEBUG_DTR
-	printk(KERN_DEBUG "%s: raising Z DTR\n", __func__);
-#endif
-}
-
-static const struct tty_port_operations cyy_port_ops = {
-	.carrier_raised = cyy_carrier_raised,
-	.dtr_rts = cyy_dtr_rts,
-	.shutdown = cy_do_close,
-};
-
-static const struct tty_port_operations cyz_port_ops = {
-	.carrier_raised = cyz_carrier_raised,
-	.dtr_rts = cyz_dtr_rts,
-	.shutdown = cy_do_close,
-};
-
-/*
- * ---------------------------------------------------------------------
- * cy_init() and friends
- *
- * cy_init() is called at boot-time to initialize the serial driver.
- * ---------------------------------------------------------------------
- */
-
-static int cy_init_card(struct cyclades_card *cinfo)
-{
-	struct cyclades_port *info;
-	unsigned int channel, port;
-
-	spin_lock_init(&cinfo->card_lock);
-	cinfo->intr_enabled = 0;
-
-	cinfo->ports = kcalloc(cinfo->nports, sizeof(*cinfo->ports),
-			GFP_KERNEL);
-	if (cinfo->ports == NULL) {
-		printk(KERN_ERR "Cyclades: cannot allocate ports\n");
-		return -ENOMEM;
-	}
-
-	for (channel = 0, port = cinfo->first_line; channel < cinfo->nports;
-			channel++, port++) {
-		info = &cinfo->ports[channel];
-		tty_port_init(&info->port);
-		info->magic = CYCLADES_MAGIC;
-		info->card = cinfo;
-		info->line = port;
-
-		info->port.closing_wait = CLOSING_WAIT_DELAY;
-		info->port.close_delay = 5 * HZ / 10;
-		init_completion(&info->shutdown_wait);
-
-		if (cy_is_Z(cinfo)) {
-			struct FIRM_ID *firm_id = cinfo->base_addr + ID_ADDRESS;
-			struct ZFW_CTRL *zfw_ctrl;
-
-			info->port.ops = &cyz_port_ops;
-			info->type = PORT_STARTECH;
-
-			zfw_ctrl = cinfo->base_addr +
-				(readl(&firm_id->zfwctrl_addr) & 0xfffff);
-			info->u.cyz.ch_ctrl = &zfw_ctrl->ch_ctrl[channel];
-			info->u.cyz.buf_ctrl = &zfw_ctrl->buf_ctrl[channel];
-
-			if (cinfo->hw_ver == ZO_V1)
-				info->xmit_fifo_size = CYZ_FIFO_SIZE;
-			else
-				info->xmit_fifo_size = 4 * CYZ_FIFO_SIZE;
-#ifdef CONFIG_CYZ_INTR
-			timer_setup(&info->rx_full_timer, cyz_rx_restart, 0);
-#endif
-		} else {
-			unsigned short chip_number;
-			int index = cinfo->bus_index;
-
-			info->port.ops = &cyy_port_ops;
-			info->type = PORT_CIRRUS;
-			info->xmit_fifo_size = CyMAX_CHAR_FIFO;
-			info->cor1 = CyPARITY_NONE | Cy_1_STOP | Cy_8_BITS;
-			info->cor2 = CyETC;
-			info->cor3 = 0x08;	/* _very_ small rcv threshold */
-
-			chip_number = channel / CyPORTS_PER_CHIP;
-			info->u.cyy.base_addr = cinfo->base_addr +
-				(cy_chip_offset[chip_number] << index);
-			info->chip_rev = cyy_readb(info, CyGFRCR);
-
-			if (info->chip_rev >= CD1400_REV_J) {
-				/* It is a CD1400 rev. J or later */
-				info->tbpr = baud_bpr_60[13];	/* Tx BPR */
-				info->tco = baud_co_60[13];	/* Tx CO */
-				info->rbpr = baud_bpr_60[13];	/* Rx BPR */
-				info->rco = baud_co_60[13];	/* Rx CO */
-				info->rtsdtr_inv = 1;
-			} else {
-				info->tbpr = baud_bpr_25[13];	/* Tx BPR */
-				info->tco = baud_co_25[13];	/* Tx CO */
-				info->rbpr = baud_bpr_25[13];	/* Rx BPR */
-				info->rco = baud_co_25[13];	/* Rx CO */
-				info->rtsdtr_inv = 0;
-			}
-			info->read_status_mask = CyTIMEOUT | CySPECHAR |
-				CyBREAK | CyPARITY | CyFRAME | CyOVERRUN;
-		}
-
-	}
-
-#ifndef CONFIG_CYZ_INTR
-	if (cy_is_Z(cinfo) && !timer_pending(&cyz_timerlist)) {
-		mod_timer(&cyz_timerlist, jiffies + 1);
-#ifdef CY_PCI_DEBUG
-		printk(KERN_DEBUG "Cyclades-Z polling initialized\n");
-#endif
-	}
-#endif
-	return 0;
-}
-
-/* initialize chips on Cyclom-Y card -- return number of valid
-   chips (which is number of ports/4) */
-static unsigned short cyy_init_card(void __iomem *true_base_addr,
-		int index)
-{
-	unsigned int chip_number;
-	void __iomem *base_addr;
-
-	cy_writeb(true_base_addr + (Cy_HwReset << index), 0);
-	/* Cy_HwReset is 0x1400 */
-	cy_writeb(true_base_addr + (Cy_ClrIntr << index), 0);
-	/* Cy_ClrIntr is 0x1800 */
-	udelay(500L);
-
-	for (chip_number = 0; chip_number < CyMAX_CHIPS_PER_CARD;
-							chip_number++) {
-		base_addr =
-		    true_base_addr + (cy_chip_offset[chip_number] << index);
-		mdelay(1);
-		if (readb(base_addr + (CyCCR << index)) != 0x00) {
-			/*************
-			printk(" chip #%d at %#6lx is never idle (CCR != 0)\n",
-			chip_number, (unsigned long)base_addr);
-			*************/
-			return chip_number;
-		}
-
-		cy_writeb(base_addr + (CyGFRCR << index), 0);
-		udelay(10L);
-
-		/* The Cyclom-16Y does not decode address bit 9 and therefore
-		   cannot distinguish between references to chip 0 and a non-
-		   existent chip 4.  If the preceding clearing of the supposed
-		   chip 4 GFRCR register appears at chip 0, there is no chip 4
-		   and this must be a Cyclom-16Y, not a Cyclom-32Ye.
-		 */
-		if (chip_number == 4 && readb(true_base_addr +
-				(cy_chip_offset[0] << index) +
-				(CyGFRCR << index)) == 0) {
-			return chip_number;
-		}
-
-		cy_writeb(base_addr + (CyCCR << index), CyCHIP_RESET);
-		mdelay(1);
-
-		if (readb(base_addr + (CyGFRCR << index)) == 0x00) {
-			/*
-			   printk(" chip #%d at %#6lx is not responding ",
-			   chip_number, (unsigned long)base_addr);
-			   printk("(GFRCR stayed 0)\n",
-			 */
-			return chip_number;
-		}
-		if ((0xf0 & (readb(base_addr + (CyGFRCR << index)))) !=
-				0x40) {
-			/*
-			printk(" chip #%d at %#6lx is not valid (GFRCR == "
-					"%#2x)\n",
-					chip_number, (unsigned long)base_addr,
-					base_addr[CyGFRCR<<index]);
-			 */
-			return chip_number;
-		}
-		cy_writeb(base_addr + (CyGCR << index), CyCH0_SERIAL);
-		if (readb(base_addr + (CyGFRCR << index)) >= CD1400_REV_J) {
-			/* It is a CD1400 rev. J or later */
-			/* Impossible to reach 5ms with this chip.
-			   Changed to 2ms instead (f = 500 Hz). */
-			cy_writeb(base_addr + (CyPPR << index), CyCLOCK_60_2MS);
-		} else {
-			/* f = 200 Hz */
-			cy_writeb(base_addr + (CyPPR << index), CyCLOCK_25_5MS);
-		}
-
-		/*
-		   printk(" chip #%d at %#6lx is rev 0x%2x\n",
-		   chip_number, (unsigned long)base_addr,
-		   readb(base_addr+(CyGFRCR<<index)));
-		 */
-	}
-	return chip_number;
-}				/* cyy_init_card */
-
-/*
- * ---------------------------------------------------------------------
- * cy_detect_isa() - Probe for Cyclom-Y/ISA boards.
- * sets global variables and return the number of ISA boards found.
- * ---------------------------------------------------------------------
- */
-static int __init cy_detect_isa(void)
-{
-#ifdef CONFIG_ISA
-	struct cyclades_card *card;
-	unsigned short cy_isa_irq, nboard;
-	void __iomem *cy_isa_address;
-	unsigned short i, j, k, cy_isa_nchan;
-	int isparam = 0;
-
-	nboard = 0;
-
-	/* Check for module parameters */
-	for (i = 0; i < NR_CARDS; i++) {
-		if (maddr[i] || i) {
-			isparam = 1;
-			cy_isa_addresses[i] = maddr[i];
-		}
-		if (!maddr[i])
-			break;
-	}
-
-	/* scan the address table probing for Cyclom-Y/ISA boards */
-	for (i = 0; i < NR_ISA_ADDRS; i++) {
-		unsigned int isa_address = cy_isa_addresses[i];
-		if (isa_address == 0x0000)
-			return nboard;
-
-		/* probe for CD1400... */
-		cy_isa_address = ioremap(isa_address, CyISA_Ywin);
-		if (cy_isa_address == NULL) {
-			printk(KERN_ERR "Cyclom-Y/ISA: can't remap base "
-					"address\n");
-			continue;
-		}
-		cy_isa_nchan = CyPORTS_PER_CHIP *
-			cyy_init_card(cy_isa_address, 0);
-		if (cy_isa_nchan == 0) {
-			iounmap(cy_isa_address);
-			continue;
-		}
-
-		if (isparam && i < NR_CARDS && irq[i])
-			cy_isa_irq = irq[i];
-		else
-			/* find out the board's irq by probing */
-			cy_isa_irq = detect_isa_irq(cy_isa_address);
-		if (cy_isa_irq == 0) {
-			printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but the "
-				"IRQ could not be detected.\n",
-				(unsigned long)cy_isa_address);
-			iounmap(cy_isa_address);
-			continue;
-		}
-
-		if ((cy_next_channel + cy_isa_nchan) > NR_PORTS) {
-			printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but no "
-				"more channels are available. Change NR_PORTS "
-				"in cyclades.c and recompile kernel.\n",
-				(unsigned long)cy_isa_address);
-			iounmap(cy_isa_address);
-			return nboard;
-		}
-		/* fill the next cy_card structure available */
-		for (j = 0; j < NR_CARDS; j++) {
-			card = &cy_card[j];
-			if (card->base_addr == NULL)
-				break;
-		}
-		if (j == NR_CARDS) {	/* no more cy_cards available */
-			printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but no "
-				"more cards can be used. Change NR_CARDS in "
-				"cyclades.c and recompile kernel.\n",
-				(unsigned long)cy_isa_address);
-			iounmap(cy_isa_address);
-			return nboard;
-		}
-
-		/* allocate IRQ */
-		if (request_irq(cy_isa_irq, cyy_interrupt,
-				0, "Cyclom-Y", card)) {
-			printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but "
-				"could not allocate IRQ#%d.\n",
-				(unsigned long)cy_isa_address, cy_isa_irq);
-			iounmap(cy_isa_address);
-			return nboard;
-		}
-
-		/* set cy_card */
-		card->base_addr = cy_isa_address;
-		card->ctl_addr.p9050 = NULL;
-		card->irq = (int)cy_isa_irq;
-		card->bus_index = 0;
-		card->first_line = cy_next_channel;
-		card->num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
-		card->nports = cy_isa_nchan;
-		if (cy_init_card(card)) {
-			card->base_addr = NULL;
-			free_irq(cy_isa_irq, card);
-			iounmap(cy_isa_address);
-			continue;
-		}
-		nboard++;
-
-		printk(KERN_INFO "Cyclom-Y/ISA #%d: 0x%lx-0x%lx, IRQ%d found: "
-			"%d channels starting from port %d\n",
-			j + 1, (unsigned long)cy_isa_address,
-			(unsigned long)(cy_isa_address + (CyISA_Ywin - 1)),
-			cy_isa_irq, cy_isa_nchan, cy_next_channel);
-
-		for (k = 0, j = cy_next_channel;
-				j < cy_next_channel + cy_isa_nchan; j++, k++)
-			tty_port_register_device(&card->ports[k].port,
-					cy_serial_driver, j, NULL);
-		cy_next_channel += cy_isa_nchan;
-	}
-	return nboard;
-#else
-	return 0;
-#endif				/* CONFIG_ISA */
-}				/* cy_detect_isa */
-
-#ifdef CONFIG_PCI
-static inline int cyc_isfwstr(const char *str, unsigned int size)
-{
-	unsigned int a;
-
-	for (a = 0; a < size && *str; a++, str++)
-		if (*str & 0x80)
-			return -EINVAL;
-
-	for (; a < size; a++, str++)
-		if (*str)
-			return -EINVAL;
-
-	return 0;
-}
-
-static inline void cyz_fpga_copy(void __iomem *fpga, const u8 *data,
-		unsigned int size)
-{
-	for (; size > 0; size--) {
-		cy_writel(fpga, *data++);
-		udelay(10);
-	}
-}
-
-static void plx_init(struct pci_dev *pdev, int irq,
-		struct RUNTIME_9060 __iomem *addr)
-{
-	/* Reset PLX */
-	cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) | 0x40000000);
-	udelay(100L);
-	cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) & ~0x40000000);
-
-	/* Reload Config. Registers from EEPROM */
-	cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) | 0x20000000);
-	udelay(100L);
-	cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) & ~0x20000000);
-
-	/* For some yet unknown reason, once the PLX9060 reloads the EEPROM,
-	 * the IRQ is lost and, thus, we have to re-write it to the PCI config.
-	 * registers. This will remain here until we find a permanent fix.
-	 */
-	pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, irq);
-}
-
-static int __cyz_load_fw(const struct firmware *fw,
-		const char *name, const u32 mailbox, void __iomem *base,
-		void __iomem *fpga)
-{
-	const void *ptr = fw->data;
-	const struct zfile_header *h = ptr;
-	const struct zfile_config *c, *cs;
-	const struct zfile_block *b, *bs;
-	unsigned int a, tmp, len = fw->size;
-#define BAD_FW KERN_ERR "Bad firmware: "
-	if (len < sizeof(*h)) {
-		printk(BAD_FW "too short: %u<%zu\n", len, sizeof(*h));
-		return -EINVAL;
-	}
-
-	cs = ptr + h->config_offset;
-	bs = ptr + h->block_offset;
-
-	if ((void *)(cs + h->n_config) > ptr + len ||
-			(void *)(bs + h->n_blocks) > ptr + len) {
-		printk(BAD_FW "too short");
-		return  -EINVAL;
-	}
-
-	if (cyc_isfwstr(h->name, sizeof(h->name)) ||
-			cyc_isfwstr(h->date, sizeof(h->date))) {
-		printk(BAD_FW "bad formatted header string\n");
-		return -EINVAL;
-	}
-
-	if (strncmp(name, h->name, sizeof(h->name))) {
-		printk(BAD_FW "bad name '%s' (expected '%s')\n", h->name, name);
-		return -EINVAL;
-	}
-
-	tmp = 0;
-	for (c = cs; c < cs + h->n_config; c++) {
-		for (a = 0; a < c->n_blocks; a++)
-			if (c->block_list[a] > h->n_blocks) {
-				printk(BAD_FW "bad block ref number in cfgs\n");
-				return -EINVAL;
-			}
-		if (c->mailbox == mailbox && c->function == 0) /* 0 is normal */
-			tmp++;
-	}
-	if (!tmp) {
-		printk(BAD_FW "nothing appropriate\n");
-		return -EINVAL;
-	}
-
-	for (b = bs; b < bs + h->n_blocks; b++)
-		if (b->file_offset + b->size > len) {
-			printk(BAD_FW "bad block data offset\n");
-			return -EINVAL;
-		}
-
-	/* everything is OK, let's seek'n'load it */
-	for (c = cs; c < cs + h->n_config; c++)
-		if (c->mailbox == mailbox && c->function == 0)
-			break;
-
-	for (a = 0; a < c->n_blocks; a++) {
-		b = &bs[c->block_list[a]];
-		if (b->type == ZBLOCK_FPGA) {
-			if (fpga != NULL)
-				cyz_fpga_copy(fpga, ptr + b->file_offset,
-						b->size);
-		} else {
-			if (base != NULL)
-				memcpy_toio(base + b->ram_offset,
-					       ptr + b->file_offset, b->size);
-		}
-	}
-#undef BAD_FW
-	return 0;
-}
-
-static int cyz_load_fw(struct pci_dev *pdev, void __iomem *base_addr,
-		struct RUNTIME_9060 __iomem *ctl_addr, int irq)
-{
-	const struct firmware *fw;
-	struct FIRM_ID __iomem *fid = base_addr + ID_ADDRESS;
-	struct CUSTOM_REG __iomem *cust = base_addr;
-	struct ZFW_CTRL __iomem *pt_zfwctrl;
-	void __iomem *tmp;
-	u32 mailbox, status, nchan;
-	unsigned int i;
-	int retval;
-
-	retval = request_firmware(&fw, "cyzfirm.bin", &pdev->dev);
-	if (retval) {
-		dev_err(&pdev->dev, "can't get firmware\n");
-		goto err;
-	}
-
-	/* Check whether the firmware is already loaded and running. If
-	   positive, skip this board */
-	if (__cyz_fpga_loaded(ctl_addr) && readl(&fid->signature) == ZFIRM_ID) {
-		u32 cntval = readl(base_addr + 0x190);
-
-		udelay(100);
-		if (cntval != readl(base_addr + 0x190)) {
-			/* FW counter is working, FW is running */
-			dev_dbg(&pdev->dev, "Cyclades-Z FW already loaded. "
-					"Skipping board.\n");
-			retval = 0;
-			goto err_rel;
-		}
-	}
-
-	/* start boot */
-	cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) &
-			~0x00030800UL);
-
-	mailbox = readl(&ctl_addr->mail_box_0);
-
-	if (mailbox == 0 || __cyz_fpga_loaded(ctl_addr)) {
-		/* stops CPU and set window to beginning of RAM */
-		cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
-		cy_writel(&cust->cpu_stop, 0);
-		cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
-		udelay(100);
-	}
-
-	plx_init(pdev, irq, ctl_addr);
-
-	if (mailbox != 0) {
-		/* load FPGA */
-		retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, NULL,
-				base_addr);
-		if (retval)
-			goto err_rel;
-		if (!__cyz_fpga_loaded(ctl_addr)) {
-			dev_err(&pdev->dev, "fw upload successful, but fw is "
-					"not loaded\n");
-			goto err_rel;
-		}
-	}
-
-	/* stops CPU and set window to beginning of RAM */
-	cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
-	cy_writel(&cust->cpu_stop, 0);
-	cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
-	udelay(100);
-
-	/* clear memory */
-	for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++)
-		cy_writeb(tmp, 255);
-	if (mailbox != 0) {
-		/* set window to last 512K of RAM */
-		cy_writel(&ctl_addr->loc_addr_base, WIN_RAM + RAM_SIZE);
-		for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++)
-			cy_writeb(tmp, 255);
-		/* set window to beginning of RAM */
-		cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
-	}
-
-	retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, base_addr, NULL);
-	release_firmware(fw);
-	if (retval)
-		goto err;
-
-	/* finish boot and start boards */
-	cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
-	cy_writel(&cust->cpu_start, 0);
-	cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
-	i = 0;
-	while ((status = readl(&fid->signature)) != ZFIRM_ID && i++ < 40)
-		msleep(100);
-	if (status != ZFIRM_ID) {
-		if (status == ZFIRM_HLT) {
-			dev_err(&pdev->dev, "you need an external power supply "
-				"for this number of ports. Firmware halted and "
-				"board reset.\n");
-			retval = -EIO;
-			goto err;
-		}
-		dev_warn(&pdev->dev, "fid->signature = 0x%x... Waiting "
-				"some more time\n", status);
-		while ((status = readl(&fid->signature)) != ZFIRM_ID &&
-				i++ < 200)
-			msleep(100);
-		if (status != ZFIRM_ID) {
-			dev_err(&pdev->dev, "Board not started in 20 seconds! "
-					"Giving up. (fid->signature = 0x%x)\n",
-					status);
-			dev_info(&pdev->dev, "*** Warning ***: if you are "
-				"upgrading the FW, please power cycle the "
-				"system before loading the new FW to the "
-				"Cyclades-Z.\n");
-
-			if (__cyz_fpga_loaded(ctl_addr))
-				plx_init(pdev, irq, ctl_addr);
-
-			retval = -EIO;
-			goto err;
-		}
-		dev_dbg(&pdev->dev, "Firmware started after %d seconds.\n",
-				i / 10);
-	}
-	pt_zfwctrl = base_addr + readl(&fid->zfwctrl_addr);
-
-	dev_dbg(&pdev->dev, "fid=> %p, zfwctrl_addr=> %x, npt_zfwctrl=> %p\n",
-			base_addr + ID_ADDRESS, readl(&fid->zfwctrl_addr),
-			base_addr + readl(&fid->zfwctrl_addr));
-
-	nchan = readl(&pt_zfwctrl->board_ctrl.n_channel);
-	dev_info(&pdev->dev, "Cyclades-Z FW loaded: version = %x, ports = %u\n",
-		readl(&pt_zfwctrl->board_ctrl.fw_version), nchan);
-
-	if (nchan == 0) {
-		dev_warn(&pdev->dev, "no Cyclades-Z ports were found. Please "
-			"check the connection between the Z host card and the "
-			"serial expanders.\n");
-
-		if (__cyz_fpga_loaded(ctl_addr))
-			plx_init(pdev, irq, ctl_addr);
-
-		dev_info(&pdev->dev, "Null number of ports detected. Board "
-				"reset.\n");
-		retval = 0;
-		goto err;
-	}
-
-	cy_writel(&pt_zfwctrl->board_ctrl.op_system, C_OS_LINUX);
-	cy_writel(&pt_zfwctrl->board_ctrl.dr_version, DRIVER_VERSION);
-
-	/*
-	   Early firmware failed to start looking for commands.
-	   This enables firmware interrupts for those commands.
-	 */
-	cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) |
-			(1 << 17));
-	cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) |
-			0x00030800UL);
-
-	return nchan;
-err_rel:
-	release_firmware(fw);
-err:
-	return retval;
-}
-
-static int cy_pci_probe(struct pci_dev *pdev,
-		const struct pci_device_id *ent)
-{
-	struct cyclades_card *card;
-	void __iomem *addr0 = NULL, *addr2 = NULL;
-	char *card_name = NULL;
-	u32 mailbox;
-	unsigned int device_id, nchan = 0, card_no, i, j;
-	unsigned char plx_ver;
-	int retval, irq;
-
-	retval = pci_enable_device(pdev);
-	if (retval) {
-		dev_err(&pdev->dev, "cannot enable device\n");
-		goto err;
-	}
-
-	/* read PCI configuration area */
-	irq = pdev->irq;
-	device_id = pdev->device & ~PCI_DEVICE_ID_MASK;
-
-#if defined(__alpha__)
-	if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) {	/* below 1M? */
-		dev_err(&pdev->dev, "Cyclom-Y/PCI not supported for low "
-			"addresses on Alpha systems.\n");
-		retval = -EIO;
-		goto err_dis;
-	}
-#endif
-	if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) {
-		dev_err(&pdev->dev, "Cyclades-Z/PCI not supported for low "
-			"addresses\n");
-		retval = -EIO;
-		goto err_dis;
-	}
-
-	if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
-		dev_warn(&pdev->dev, "PCI I/O bit incorrectly set. Ignoring "
-				"it...\n");
-		pdev->resource[2].flags &= ~IORESOURCE_IO;
-	}
-
-	retval = pci_request_regions(pdev, "cyclades");
-	if (retval) {
-		dev_err(&pdev->dev, "failed to reserve resources\n");
-		goto err_dis;
-	}
-
-	retval = -EIO;
-	if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
-			device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
-		card_name = "Cyclom-Y";
-
-		addr0 = ioremap(pci_resource_start(pdev, 0),
-				CyPCI_Yctl);
-		if (addr0 == NULL) {
-			dev_err(&pdev->dev, "can't remap ctl region\n");
-			goto err_reg;
-		}
-		addr2 = ioremap(pci_resource_start(pdev, 2),
-				CyPCI_Ywin);
-		if (addr2 == NULL) {
-			dev_err(&pdev->dev, "can't remap base region\n");
-			goto err_unmap;
-		}
-
-		nchan = CyPORTS_PER_CHIP * cyy_init_card(addr2, 1);
-		if (nchan == 0) {
-			dev_err(&pdev->dev, "Cyclom-Y PCI host card with no "
-					"Serial-Modules\n");
-			goto err_unmap;
-		}
-	} else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
-		struct RUNTIME_9060 __iomem *ctl_addr;
-
-		ctl_addr = addr0 = ioremap(pci_resource_start(pdev, 0),
-				CyPCI_Zctl);
-		if (addr0 == NULL) {
-			dev_err(&pdev->dev, "can't remap ctl region\n");
-			goto err_reg;
-		}
-
-		/* Disable interrupts on the PLX before resetting it */
-		cy_writew(&ctl_addr->intr_ctrl_stat,
-				readw(&ctl_addr->intr_ctrl_stat) & ~0x0900);
-
-		plx_init(pdev, irq, addr0);
-
-		mailbox = readl(&ctl_addr->mail_box_0);
-
-		addr2 = ioremap(pci_resource_start(pdev, 2),
-				mailbox == ZE_V1 ? CyPCI_Ze_win : CyPCI_Zwin);
-		if (addr2 == NULL) {
-			dev_err(&pdev->dev, "can't remap base region\n");
-			goto err_unmap;
-		}
-
-		if (mailbox == ZE_V1) {
-			card_name = "Cyclades-Ze";
-		} else {
-			card_name = "Cyclades-8Zo";
-#ifdef CY_PCI_DEBUG
-			if (mailbox == ZO_V1) {
-				cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
-				dev_info(&pdev->dev, "Cyclades-8Zo/PCI: FPGA "
-					"id %lx, ver %lx\n", (ulong)(0xff &
-					readl(&((struct CUSTOM_REG *)addr2)->
-						fpga_id)), (ulong)(0xff &
-					readl(&((struct CUSTOM_REG *)addr2)->
-						fpga_version)));
-				cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
-			} else {
-				dev_info(&pdev->dev, "Cyclades-Z/PCI: New "
-					"Cyclades-Z board.  FPGA not loaded\n");
-			}
-#endif
-			/* The following clears the firmware id word.  This
-			   ensures that the driver will not attempt to talk to
-			   the board until it has been properly initialized.
-			 */
-			if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
-				cy_writel(addr2 + ID_ADDRESS, 0L);
-		}
-
-		retval = cyz_load_fw(pdev, addr2, addr0, irq);
-		if (retval <= 0)
-			goto err_unmap;
-		nchan = retval;
-	}
-
-	if ((cy_next_channel + nchan) > NR_PORTS) {
-		dev_err(&pdev->dev, "Cyclades-8Zo/PCI found, but no "
-			"channels are available. Change NR_PORTS in "
-			"cyclades.c and recompile kernel.\n");
-		goto err_unmap;
-	}
-	/* fill the next cy_card structure available */
-	for (card_no = 0; card_no < NR_CARDS; card_no++) {
-		card = &cy_card[card_no];
-		if (card->base_addr == NULL)
-			break;
-	}
-	if (card_no == NR_CARDS) {	/* no more cy_cards available */
-		dev_err(&pdev->dev, "Cyclades-8Zo/PCI found, but no "
-			"more cards can be used. Change NR_CARDS in "
-			"cyclades.c and recompile kernel.\n");
-		goto err_unmap;
-	}
-
-	if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
-			device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
-		/* allocate IRQ */
-		retval = request_irq(irq, cyy_interrupt,
-				IRQF_SHARED, "Cyclom-Y", card);
-		if (retval) {
-			dev_err(&pdev->dev, "could not allocate IRQ\n");
-			goto err_unmap;
-		}
-		card->num_chips = nchan / CyPORTS_PER_CHIP;
-	} else {
-		struct FIRM_ID __iomem *firm_id = addr2 + ID_ADDRESS;
-		struct ZFW_CTRL __iomem *zfw_ctrl;
-
-		zfw_ctrl = addr2 + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
-
-		card->hw_ver = mailbox;
-		card->num_chips = (unsigned int)-1;
-		card->board_ctrl = &zfw_ctrl->board_ctrl;
-#ifdef CONFIG_CYZ_INTR
-		/* allocate IRQ only if board has an IRQ */
-		if (irq != 0 && irq != 255) {
-			retval = request_irq(irq, cyz_interrupt,
-					IRQF_SHARED, "Cyclades-Z", card);
-			if (retval) {
-				dev_err(&pdev->dev, "could not allocate IRQ\n");
-				goto err_unmap;
-			}
-		}
-#endif				/* CONFIG_CYZ_INTR */
-	}
-
-	/* set cy_card */
-	card->base_addr = addr2;
-	card->ctl_addr.p9050 = addr0;
-	card->irq = irq;
-	card->bus_index = 1;
-	card->first_line = cy_next_channel;
-	card->nports = nchan;
-	retval = cy_init_card(card);
-	if (retval)
-		goto err_null;
-
-	pci_set_drvdata(pdev, card);
-
-	if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
-			device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
-		/* enable interrupts in the PCI interface */
-		plx_ver = readb(addr2 + CyPLX_VER) & 0x0f;
-		switch (plx_ver) {
-		case PLX_9050:
-			cy_writeb(addr0 + 0x4c, 0x43);
-			break;
-
-		case PLX_9060:
-		case PLX_9080:
-		default:	/* Old boards, use PLX_9060 */
-		{
-			struct RUNTIME_9060 __iomem *ctl_addr = addr0;
-			plx_init(pdev, irq, ctl_addr);
-			cy_writew(&ctl_addr->intr_ctrl_stat,
-				readw(&ctl_addr->intr_ctrl_stat) | 0x0900);
-			break;
-		}
-		}
-	}
-
-	dev_info(&pdev->dev, "%s/PCI #%d found: %d channels starting from "
-		"port %d.\n", card_name, card_no + 1, nchan, cy_next_channel);
-	for (j = 0, i = cy_next_channel; i < cy_next_channel + nchan; i++, j++)
-		tty_port_register_device(&card->ports[j].port,
-				cy_serial_driver, i, &pdev->dev);
-	cy_next_channel += nchan;
-
-	return 0;
-err_null:
-	card->base_addr = NULL;
-	free_irq(irq, card);
-err_unmap:
-	iounmap(addr0);
-	if (addr2)
-		iounmap(addr2);
-err_reg:
-	pci_release_regions(pdev);
-err_dis:
-	pci_disable_device(pdev);
-err:
-	return retval;
-}
-
-static void cy_pci_remove(struct pci_dev *pdev)
-{
-	struct cyclades_card *cinfo = pci_get_drvdata(pdev);
-	unsigned int i, channel;
-
-	/* non-Z with old PLX */
-	if (!cy_is_Z(cinfo) && (readb(cinfo->base_addr + CyPLX_VER) & 0x0f) ==
-			PLX_9050)
-		cy_writeb(cinfo->ctl_addr.p9050 + 0x4c, 0);
-	else
-#ifndef CONFIG_CYZ_INTR
-		if (!cy_is_Z(cinfo))
-#endif
-		cy_writew(&cinfo->ctl_addr.p9060->intr_ctrl_stat,
-			readw(&cinfo->ctl_addr.p9060->intr_ctrl_stat) &
-			~0x0900);
-
-	iounmap(cinfo->base_addr);
-	if (cinfo->ctl_addr.p9050)
-		iounmap(cinfo->ctl_addr.p9050);
-	if (cinfo->irq
-#ifndef CONFIG_CYZ_INTR
-		&& !cy_is_Z(cinfo)
-#endif /* CONFIG_CYZ_INTR */
-		)
-		free_irq(cinfo->irq, cinfo);
-	pci_release_regions(pdev);
-
-	cinfo->base_addr = NULL;
-	for (channel = 0, i = cinfo->first_line; i < cinfo->first_line +
-			cinfo->nports; i++, channel++) {
-		tty_unregister_device(cy_serial_driver, i);
-		tty_port_destroy(&cinfo->ports[channel].port);
-	}
-	cinfo->nports = 0;
-	kfree(cinfo->ports);
-}
-
-static struct pci_driver cy_pci_driver = {
-	.name = "cyclades",
-	.id_table = cy_pci_dev_id,
-	.probe = cy_pci_probe,
-	.remove = cy_pci_remove
-};
-#endif
-
-static int cyclades_proc_show(struct seq_file *m, void *v)
-{
-	struct cyclades_port *info;
-	unsigned int i, j;
-	__u32 cur_jifs = jiffies;
-
-	seq_puts(m, "Dev TimeOpen   BytesOut  IdleOut    BytesIn   "
-			"IdleIn  Overruns  Ldisc\n");
-
-	/* Output one line for each known port */
-	for (i = 0; i < NR_CARDS; i++)
-		for (j = 0; j < cy_card[i].nports; j++) {
-			info = &cy_card[i].ports[j];
-
-			if (info->port.count) {
-				/* XXX is the ldisc num worth this? */
-				struct tty_struct *tty;
-				struct tty_ldisc *ld;
-				int num = 0;
-				tty = tty_port_tty_get(&info->port);
-				if (tty) {
-					ld = tty_ldisc_ref(tty);
-					if (ld) {
-						num = ld->ops->num;
-						tty_ldisc_deref(ld);
-					}
-					tty_kref_put(tty);
-				}
-				seq_printf(m, "%3d %8lu %10lu %8lu "
-					"%10lu %8lu %9lu %6d\n", info->line,
-					(cur_jifs - info->idle_stats.in_use) /
-					HZ, info->idle_stats.xmit_bytes,
-					(cur_jifs - info->idle_stats.xmit_idle)/
-					HZ, info->idle_stats.recv_bytes,
-					(cur_jifs - info->idle_stats.recv_idle)/
-					HZ, info->idle_stats.overruns,
-					num);
-			} else
-				seq_printf(m, "%3d %8lu %10lu %8lu "
-					"%10lu %8lu %9lu %6ld\n",
-					info->line, 0L, 0L, 0L, 0L, 0L, 0L, 0L);
-		}
-	return 0;
-}
-
-/* The serial driver boot-time initialization code!
-    Hardware I/O ports are mapped to character special devices on a
-    first found, first allocated manner.  That is, this code searches
-    for Cyclom cards in the system.  As each is found, it is probed
-    to discover how many chips (and thus how many ports) are present.
-    These ports are mapped to the tty ports 32 and upward in monotonic
-    fashion.  If an 8-port card is replaced with a 16-port card, the
-    port mapping on a following card will shift.
-
-    This approach is different from what is used in the other serial
-    device driver because the Cyclom is more properly a multiplexer,
-    not just an aggregation of serial ports on one card.
-
-    If there are more cards with more ports than have been
-    statically allocated above, a warning is printed and the
-    extra ports are ignored.
- */
-
-static const struct tty_operations cy_ops = {
-	.open = cy_open,
-	.close = cy_close,
-	.write = cy_write,
-	.put_char = cy_put_char,
-	.flush_chars = cy_flush_chars,
-	.write_room = cy_write_room,
-	.chars_in_buffer = cy_chars_in_buffer,
-	.flush_buffer = cy_flush_buffer,
-	.ioctl = cy_ioctl,
-	.throttle = cy_throttle,
-	.unthrottle = cy_unthrottle,
-	.set_termios = cy_set_termios,
-	.stop = cy_stop,
-	.start = cy_start,
-	.hangup = cy_hangup,
-	.break_ctl = cy_break,
-	.wait_until_sent = cy_wait_until_sent,
-	.tiocmget = cy_tiocmget,
-	.tiocmset = cy_tiocmset,
-	.get_icount = cy_get_icount,
-	.set_serial = cy_set_serial_info,
-	.get_serial = cy_get_serial_info,
-	.proc_show = cyclades_proc_show,
-};
-
-static int __init cy_init(void)
-{
-	unsigned int nboards;
-	int retval = -ENOMEM;
-
-	cy_serial_driver = alloc_tty_driver(NR_PORTS);
-	if (!cy_serial_driver)
-		goto err;
-
-	printk(KERN_INFO "Cyclades driver " CY_VERSION "\n");
-
-	/* Initialize the tty_driver structure */
-
-	cy_serial_driver->driver_name = "cyclades";
-	cy_serial_driver->name = "ttyC";
-	cy_serial_driver->major = CYCLADES_MAJOR;
-	cy_serial_driver->minor_start = 0;
-	cy_serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
-	cy_serial_driver->subtype = SERIAL_TYPE_NORMAL;
-	cy_serial_driver->init_termios = tty_std_termios;
-	cy_serial_driver->init_termios.c_cflag =
-	    B9600 | CS8 | CREAD | HUPCL | CLOCAL;
-	cy_serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
-	tty_set_operations(cy_serial_driver, &cy_ops);
-
-	retval = tty_register_driver(cy_serial_driver);
-	if (retval) {
-		printk(KERN_ERR "Couldn't register Cyclades serial driver\n");
-		goto err_frtty;
-	}
-
-	/* the code below is responsible to find the boards. Each different
-	   type of board has its own detection routine. If a board is found,
-	   the next cy_card structure available is set by the detection
-	   routine. These functions are responsible for checking the
-	   availability of cy_card and cy_port data structures and updating
-	   the cy_next_channel. */
-
-	/* look for isa boards */
-	nboards = cy_detect_isa();
-
-#ifdef CONFIG_PCI
-	/* look for pci boards */
-	retval = pci_register_driver(&cy_pci_driver);
-	if (retval && !nboards) {
-		tty_unregister_driver(cy_serial_driver);
-		goto err_frtty;
-	}
-#endif
-
-	return 0;
-err_frtty:
-	put_tty_driver(cy_serial_driver);
-err:
-	return retval;
-}				/* cy_init */
-
-static void __exit cy_cleanup_module(void)
-{
-	struct cyclades_card *card;
-	unsigned int i, e1;
-
-#ifndef CONFIG_CYZ_INTR
-	del_timer_sync(&cyz_timerlist);
-#endif /* CONFIG_CYZ_INTR */
-
-	e1 = tty_unregister_driver(cy_serial_driver);
-	if (e1)
-		printk(KERN_ERR "failed to unregister Cyclades serial "
-				"driver(%d)\n", e1);
-
-#ifdef CONFIG_PCI
-	pci_unregister_driver(&cy_pci_driver);
-#endif
-
-	for (i = 0; i < NR_CARDS; i++) {
-		card = &cy_card[i];
-		if (card->base_addr) {
-			/* clear interrupt */
-			cy_writeb(card->base_addr + Cy_ClrIntr, 0);
-			iounmap(card->base_addr);
-			if (card->ctl_addr.p9050)
-				iounmap(card->ctl_addr.p9050);
-			if (card->irq
-#ifndef CONFIG_CYZ_INTR
-				&& !cy_is_Z(card)
-#endif /* CONFIG_CYZ_INTR */
-				)
-				free_irq(card->irq, card);
-			for (e1 = card->first_line; e1 < card->first_line +
-					card->nports; e1++)
-				tty_unregister_device(cy_serial_driver, e1);
-			kfree(card->ports);
-		}
-	}
-
-	put_tty_driver(cy_serial_driver);
-} /* cy_cleanup_module */
-
-module_init(cy_init);
-module_exit(cy_cleanup_module);
-
-MODULE_LICENSE("GPL");
-MODULE_VERSION(CY_VERSION);
-MODULE_ALIAS_CHARDEV_MAJOR(CYCLADES_MAJOR);
-MODULE_FIRMWARE("cyzfirm.bin");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 603137da4736..7ec05fdb1fc3 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -15,8 +15,7 @@  config SERIAL_8250
 	  here are those that are setting up dedicated Ethernet WWW/FTP
 	  servers, or users that have one of the various bus mice instead of a
 	  serial mouse and don't intend to use their machine's standard serial
-	  port for anything.  (Note that the Cyclades multi serial port driver
-	  does not need this driver built in for it to work.)
+	  port for anything.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called 8250.
@@ -226,7 +225,7 @@  config SERIAL_8250_MANY_PORTS
 	  serial port hardware which acts similar to standard serial port
 	  hardware. If you only use the standard COM 1/2/3/4 ports, you can
 	  say N here to save some memory. You can also say Y if you have an
-	  "intelligent" multiport card such as Cyclades, Digiboards, etc.
+	  "intelligent" multiport card such as Digiboards, etc.
 
 #
 # Multi-port serial cards
diff --git a/include/linux/cyclades.h b/include/linux/cyclades.h
deleted file mode 100644
index 05ee0f19448a..000000000000
--- a/include/linux/cyclades.h
+++ /dev/null
@@ -1,364 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0 */
-/* $Revision: 3.0 $$Date: 1998/11/02 14:20:59 $
- * linux/include/linux/cyclades.h
- *
- * This file was initially written by
- * Randolph Bentson <bentson@grieg.seaslug.org> and is maintained by
- * Ivan Passos <ivan@cyclades.com>.
- *
- * This file contains the general definitions for the cyclades.c driver
- *$Log: cyclades.h,v $
- *Revision 3.1  2002/01/29 11:36:16  henrique
- *added throttle field on struct cyclades_port to indicate whether the
- *port is throttled or not
- *
- *Revision 3.1  2000/04/19 18:52:52  ivan
- *converted address fields to unsigned long and added fields for physical
- *addresses on cyclades_card structure;
- *
- *Revision 3.0  1998/11/02 14:20:59  ivan
- *added nports field on cyclades_card structure;
- *
- *Revision 2.5  1998/08/03 16:57:01  ivan
- *added cyclades_idle_stats structure;
- * 
- *Revision 2.4  1998/06/01 12:09:53  ivan
- *removed closing_wait2 from cyclades_port structure;
- *
- *Revision 2.3  1998/03/16 18:01:12  ivan
- *changes in the cyclades_port structure to get it closer to the 
- *standard serial port structure;
- *added constants for new ioctls;
- *
- *Revision 2.2  1998/02/17 16:50:00  ivan
- *changes in the cyclades_port structure (addition of shutdown_wait and 
- *chip_rev variables);
- *added constants for new ioctls and for CD1400 rev. numbers.
- *
- *Revision 2.1	1997/10/24 16:03:00  ivan
- *added rflow (which allows enabling the CD1400 special flow control 
- *feature) and rtsdtr_inv (which allows DTR/RTS pin inversion) to 
- *cyclades_port structure;
- *added Alpha support
- *
- *Revision 2.0  1997/06/30 10:30:00  ivan
- *added some new doorbell command constants related to IOCTLW and
- *UART error signaling
- *
- *Revision 1.8  1997/06/03 15:30:00  ivan
- *added constant ZFIRM_HLT
- *added constant CyPCI_Ze_win ( = 2 * Cy_PCI_Zwin)
- *
- *Revision 1.7  1997/03/26 10:30:00  daniel
- *new entries at the end of cyclades_port struct to reallocate
- *variables illegally allocated within card memory.
- *
- *Revision 1.6  1996/09/09 18:35:30  bentson
- *fold in changes for Cyclom-Z -- including structures for
- *communicating with board as well modest changes to original
- *structures to support new features.
- *
- *Revision 1.5  1995/11/13 21:13:31  bentson
- *changes suggested by Michael Chastain <mec@duracef.shout.net>
- *to support use of this file in non-kernel applications
- *
- *
- */
-#ifndef _LINUX_CYCLADES_H
-#define _LINUX_CYCLADES_H
-
-#include <uapi/linux/cyclades.h>
-
-
-/* Per card data structure */
-struct cyclades_card {
-	void __iomem *base_addr;
-	union {
-		void __iomem *p9050;
-		struct RUNTIME_9060 __iomem *p9060;
-	} ctl_addr;
-	struct BOARD_CTRL __iomem *board_ctrl;	/* cyz specific */
-	int irq;
-	unsigned int num_chips;	/* 0 if card absent, -1 if Z/PCI, else Y */
-	unsigned int first_line;	/* minor number of first channel on card */
-	unsigned int nports;	/* Number of ports in the card */
-	int bus_index;		/* address shift - 0 for ISA, 1 for PCI */
-	int intr_enabled;		/* FW Interrupt flag - 0 disabled, 1 enabled */
-	u32 hw_ver;
-	spinlock_t card_lock;
-	struct cyclades_port *ports;
-};
-
-/***************************************
- * Memory access functions/macros      *
- * (required to support Alpha systems) *
- ***************************************/
-
-#define cy_writeb(port,val)     do { writeb((val), (port)); mb(); } while (0)
-#define cy_writew(port,val)     do { writew((val), (port)); mb(); } while (0)
-#define cy_writel(port,val)     do { writel((val), (port)); mb(); } while (0)
-
-/*
- * Statistics counters
- */
-struct cyclades_icount {
-	__u32	cts, dsr, rng, dcd, tx, rx;
-	__u32	frame, parity, overrun, brk;
-	__u32	buf_overrun;
-};
-
-/*
- * This is our internal structure for each serial port's state.
- * 
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct cyclades_port {
-	int                     magic;
-	struct tty_port		port;
-	struct cyclades_card	*card;
-	union {
-		struct {
-			void __iomem *base_addr;
-		} cyy;
-		struct {
-			struct CH_CTRL __iomem	*ch_ctrl;
-			struct BUF_CTRL __iomem	*buf_ctrl;
-		} cyz;
-	} u;
-	int			line;
-	int			flags; 		/* defined in tty.h */
-	int                     type;		/* UART type */
-	int			read_status_mask;
-	int			ignore_status_mask;
-	int			timeout;
-	int			xmit_fifo_size;
-	int                     cor1,cor2,cor3,cor4,cor5;
-	int                     tbpr,tco,rbpr,rco;
-	int			baud;
-	int			rflow;
-	int			rtsdtr_inv;
-	int			chip_rev;
-	int			custom_divisor;
-	u8			x_char; /* to be pushed out ASAP */
-	int                     breakon;
-	int                     breakoff;
-	int			xmit_head;
-	int			xmit_tail;
-	int			xmit_cnt;
-        int                     default_threshold;
-        int                     default_timeout;
-	unsigned long		rflush_count;
-	struct cyclades_monitor	mon;
-	struct cyclades_idle_stats	idle_stats;
-	struct cyclades_icount	icount;
-	struct completion       shutdown_wait;
-	int throttle;
-#ifdef CONFIG_CYZ_INTR
-	struct timer_list	rx_full_timer;
-#endif
-};
-
-#define	CLOSING_WAIT_DELAY	30*HZ
-#define CY_CLOSING_WAIT_NONE	ASYNC_CLOSING_WAIT_NONE
-#define CY_CLOSING_WAIT_INF	ASYNC_CLOSING_WAIT_INF
-
-
-#define CyMAX_CHIPS_PER_CARD	8
-#define CyMAX_CHAR_FIFO		12
-#define CyPORTS_PER_CHIP	4
-#define	CD1400_MAX_SPEED	115200
-
-#define	CyISA_Ywin	0x2000
-
-#define CyPCI_Ywin 	0x4000
-#define CyPCI_Yctl 	0x80
-#define CyPCI_Zctl 	CTRL_WINDOW_SIZE
-#define CyPCI_Zwin 	0x80000
-#define CyPCI_Ze_win 	(2 * CyPCI_Zwin)
-
-#define PCI_DEVICE_ID_MASK	0x06
-
-/**** CD1400 registers ****/
-
-#define CD1400_REV_G	0x46
-#define CD1400_REV_J	0x48
-
-#define CyRegSize  	0x0400
-#define Cy_HwReset 	0x1400
-#define Cy_ClrIntr 	0x1800
-#define Cy_EpldRev 	0x1e00
-
-/* Global Registers */
-
-#define CyGFRCR		(0x40*2)
-#define      CyRevE		(44)
-#define CyCAR		(0x68*2)
-#define      CyCHAN_0		(0x00)
-#define      CyCHAN_1		(0x01)
-#define      CyCHAN_2		(0x02)
-#define      CyCHAN_3		(0x03)
-#define CyGCR		(0x4B*2)
-#define      CyCH0_SERIAL	(0x00)
-#define      CyCH0_PARALLEL	(0x80)
-#define CySVRR		(0x67*2)
-#define      CySRModem		(0x04)
-#define      CySRTransmit	(0x02)
-#define      CySRReceive	(0x01)
-#define CyRICR		(0x44*2)
-#define CyTICR		(0x45*2)
-#define CyMICR		(0x46*2)
-#define      CyICR0		(0x00)
-#define      CyICR1		(0x01)
-#define      CyICR2		(0x02)
-#define      CyICR3		(0x03)
-#define CyRIR		(0x6B*2)
-#define CyTIR		(0x6A*2)
-#define CyMIR		(0x69*2)
-#define      CyIRDirEq		(0x80)
-#define      CyIRBusy		(0x40)
-#define      CyIRUnfair		(0x20)
-#define      CyIRContext	(0x1C)
-#define      CyIRChannel	(0x03)
-#define CyPPR 		(0x7E*2)
-#define      CyCLOCK_20_1MS	(0x27)
-#define      CyCLOCK_25_1MS	(0x31)
-#define      CyCLOCK_25_5MS	(0xf4)
-#define      CyCLOCK_60_1MS	(0x75)
-#define      CyCLOCK_60_2MS	(0xea)
-
-/* Virtual Registers */
-
-#define CyRIVR		(0x43*2)
-#define CyTIVR		(0x42*2)
-#define CyMIVR		(0x41*2)
-#define      CyIVRMask (0x07)
-#define      CyIVRRxEx (0x07)
-#define      CyIVRRxOK (0x03)
-#define      CyIVRTxOK (0x02)
-#define      CyIVRMdmOK (0x01)
-#define CyTDR		(0x63*2)
-#define CyRDSR		(0x62*2)
-#define      CyTIMEOUT		(0x80)
-#define      CySPECHAR		(0x70)
-#define      CyBREAK		(0x08)
-#define      CyPARITY		(0x04)
-#define      CyFRAME		(0x02)
-#define      CyOVERRUN		(0x01)
-#define CyMISR		(0x4C*2)
-/* see CyMCOR_ and CyMSVR_ for bits*/
-#define CyEOSRR		(0x60*2)
-
-/* Channel Registers */
-
-#define CyLIVR		(0x18*2)
-#define      CyMscsr		(0x01)
-#define      CyTdsr		(0x02)
-#define      CyRgdsr		(0x03)
-#define      CyRedsr		(0x07)
-#define CyCCR		(0x05*2)
-/* Format 1 */
-#define      CyCHAN_RESET	(0x80)
-#define      CyCHIP_RESET	(0x81)
-#define      CyFlushTransFIFO	(0x82)
-/* Format 2 */
-#define      CyCOR_CHANGE	(0x40)
-#define      CyCOR1ch		(0x02)
-#define      CyCOR2ch		(0x04)
-#define      CyCOR3ch		(0x08)
-/* Format 3 */
-#define      CySEND_SPEC_1	(0x21)
-#define      CySEND_SPEC_2	(0x22)
-#define      CySEND_SPEC_3	(0x23)
-#define      CySEND_SPEC_4	(0x24)
-/* Format 4 */
-#define      CyCHAN_CTL		(0x10)
-#define      CyDIS_RCVR		(0x01)
-#define      CyENB_RCVR		(0x02)
-#define      CyDIS_XMTR		(0x04)
-#define      CyENB_XMTR		(0x08)
-#define CySRER		(0x06*2)
-#define      CyMdmCh		(0x80)
-#define      CyRxData		(0x10)
-#define      CyTxRdy		(0x04)
-#define      CyTxMpty		(0x02)
-#define      CyNNDT		(0x01)
-#define CyCOR1		(0x08*2)
-#define      CyPARITY_NONE	(0x00)
-#define      CyPARITY_0		(0x20)
-#define      CyPARITY_1		(0xA0)
-#define      CyPARITY_E		(0x40)
-#define      CyPARITY_O		(0xC0)
-#define      Cy_1_STOP		(0x00)
-#define      Cy_1_5_STOP	(0x04)
-#define      Cy_2_STOP		(0x08)
-#define      Cy_5_BITS		(0x00)
-#define      Cy_6_BITS		(0x01)
-#define      Cy_7_BITS		(0x02)
-#define      Cy_8_BITS		(0x03)
-#define CyCOR2		(0x09*2)
-#define      CyIXM		(0x80)
-#define      CyTxIBE		(0x40)
-#define      CyETC		(0x20)
-#define      CyAUTO_TXFL	(0x60)
-#define      CyLLM		(0x10)
-#define      CyRLM		(0x08)
-#define      CyRtsAO		(0x04)
-#define      CyCtsAE		(0x02)
-#define      CyDsrAE		(0x01)
-#define CyCOR3		(0x0A*2)
-#define      CySPL_CH_DRANGE	(0x80)  /* special character detect range */
-#define      CySPL_CH_DET1	(0x40)  /* enable special character detection
-                                                               on SCHR4-SCHR3 */
-#define      CyFL_CTRL_TRNSP	(0x20)  /* Flow Control Transparency */
-#define      CySPL_CH_DET2	(0x10)  /* Enable special character detection
-                                                               on SCHR2-SCHR1 */
-#define      CyREC_FIFO		(0x0F)  /* Receive FIFO threshold */
-#define CyCOR4		(0x1E*2)
-#define CyCOR5		(0x1F*2)
-#define CyCCSR		(0x0B*2)
-#define      CyRxEN		(0x80)
-#define      CyRxFloff		(0x40)
-#define      CyRxFlon		(0x20)
-#define      CyTxEN		(0x08)
-#define      CyTxFloff		(0x04)
-#define      CyTxFlon		(0x02)
-#define CyRDCR		(0x0E*2)
-#define CySCHR1		(0x1A*2)
-#define CySCHR2 	(0x1B*2)
-#define CySCHR3		(0x1C*2)
-#define CySCHR4		(0x1D*2)
-#define CySCRL		(0x22*2)
-#define CySCRH		(0x23*2)
-#define CyLNC		(0x24*2)
-#define CyMCOR1 	(0x15*2)
-#define CyMCOR2		(0x16*2)
-#define CyRTPR		(0x21*2)
-#define CyMSVR1		(0x6C*2)
-#define CyMSVR2		(0x6D*2)
-#define      CyANY_DELTA	(0xF0)
-#define      CyDSR		(0x80)
-#define      CyCTS		(0x40)
-#define      CyRI		(0x20)
-#define      CyDCD		(0x10)
-#define      CyDTR              (0x02)
-#define      CyRTS              (0x01)
-#define CyPVSR		(0x6F*2)
-#define CyRBPR		(0x78*2)
-#define CyRCOR		(0x7C*2)
-#define CyTBPR		(0x72*2)
-#define CyTCOR		(0x76*2)
-
-/* Custom Registers */
-
-#define	CyPLX_VER	(0x3400)
-#define	PLX_9050	0x0b
-#define	PLX_9060	0x0c
-#define	PLX_9080	0x0d
-
-/***************************************************************************/
-
-#endif /* _LINUX_CYCLADES_H */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 8a18517696c1..056d2074f07a 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1711,14 +1711,6 @@ 
 #define PCI_DEVICE_ID_CRP16INTF		0x0903
 
 #define PCI_VENDOR_ID_CYCLADES		0x120e
-#define PCI_DEVICE_ID_CYCLOM_Y_Lo	0x0100
-#define PCI_DEVICE_ID_CYCLOM_Y_Hi	0x0101
-#define PCI_DEVICE_ID_CYCLOM_4Y_Lo	0x0102
-#define PCI_DEVICE_ID_CYCLOM_4Y_Hi	0x0103
-#define PCI_DEVICE_ID_CYCLOM_8Y_Lo	0x0104
-#define PCI_DEVICE_ID_CYCLOM_8Y_Hi	0x0105
-#define PCI_DEVICE_ID_CYCLOM_Z_Lo	0x0200
-#define PCI_DEVICE_ID_CYCLOM_Z_Hi	0x0201
 #define PCI_DEVICE_ID_PC300_RX_2	0x0300
 #define PCI_DEVICE_ID_PC300_RX_1	0x0301
 #define PCI_DEVICE_ID_PC300_TE_2	0x0310
diff --git a/include/uapi/linux/cyclades.h b/include/uapi/linux/cyclades.h
deleted file mode 100644
index fc0add2194a9..000000000000
--- a/include/uapi/linux/cyclades.h
+++ /dev/null
@@ -1,494 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
-/* $Revision: 3.0 $$Date: 1998/11/02 14:20:59 $
- * linux/include/linux/cyclades.h
- *
- * This file was initially written by
- * Randolph Bentson <bentson@grieg.seaslug.org> and is maintained by
- * Ivan Passos <ivan@cyclades.com>.
- *
- * This file contains the general definitions for the cyclades.c driver
- *$Log: cyclades.h,v $
- *Revision 3.1  2002/01/29 11:36:16  henrique
- *added throttle field on struct cyclades_port to indicate whether the
- *port is throttled or not
- *
- *Revision 3.1  2000/04/19 18:52:52  ivan
- *converted address fields to unsigned long and added fields for physical
- *addresses on cyclades_card structure;
- *
- *Revision 3.0  1998/11/02 14:20:59  ivan
- *added nports field on cyclades_card structure;
- *
- *Revision 2.5  1998/08/03 16:57:01  ivan
- *added cyclades_idle_stats structure;
- * 
- *Revision 2.4  1998/06/01 12:09:53  ivan
- *removed closing_wait2 from cyclades_port structure;
- *
- *Revision 2.3  1998/03/16 18:01:12  ivan
- *changes in the cyclades_port structure to get it closer to the 
- *standard serial port structure;
- *added constants for new ioctls;
- *
- *Revision 2.2  1998/02/17 16:50:00  ivan
- *changes in the cyclades_port structure (addition of shutdown_wait and 
- *chip_rev variables);
- *added constants for new ioctls and for CD1400 rev. numbers.
- *
- *Revision 2.1	1997/10/24 16:03:00  ivan
- *added rflow (which allows enabling the CD1400 special flow control 
- *feature) and rtsdtr_inv (which allows DTR/RTS pin inversion) to 
- *cyclades_port structure;
- *added Alpha support
- *
- *Revision 2.0  1997/06/30 10:30:00  ivan
- *added some new doorbell command constants related to IOCTLW and
- *UART error signaling
- *
- *Revision 1.8  1997/06/03 15:30:00  ivan
- *added constant ZFIRM_HLT
- *added constant CyPCI_Ze_win ( = 2 * Cy_PCI_Zwin)
- *
- *Revision 1.7  1997/03/26 10:30:00  daniel
- *new entries at the end of cyclades_port struct to reallocate
- *variables illegally allocated within card memory.
- *
- *Revision 1.6  1996/09/09 18:35:30  bentson
- *fold in changes for Cyclom-Z -- including structures for
- *communicating with board as well modest changes to original
- *structures to support new features.
- *
- *Revision 1.5  1995/11/13 21:13:31  bentson
- *changes suggested by Michael Chastain <mec@duracef.shout.net>
- *to support use of this file in non-kernel applications
- *
- *
- */
-
-#ifndef _UAPI_LINUX_CYCLADES_H
-#define _UAPI_LINUX_CYCLADES_H
-
-#include <linux/types.h>
-
-struct cyclades_monitor {
-        unsigned long           int_count;
-        unsigned long           char_count;
-        unsigned long           char_max;
-        unsigned long           char_last;
-};
-
-/*
- * These stats all reflect activity since the device was last initialized.
- * (i.e., since the port was opened with no other processes already having it
- * open)
- */
-struct cyclades_idle_stats {
-    __kernel_old_time_t in_use;	/* Time device has been in use (secs) */
-    __kernel_old_time_t recv_idle; /* Time since last char received (secs) */
-    __kernel_old_time_t xmit_idle; /* Time since last char transmitted (secs) */
-    unsigned long  recv_bytes;	/* Bytes received */
-    unsigned long  xmit_bytes;	/* Bytes transmitted */
-    unsigned long  overruns;	/* Input overruns */
-    unsigned long  frame_errs;	/* Input framing errors */
-    unsigned long  parity_errs;	/* Input parity errors */
-};
-
-#define CYCLADES_MAGIC  0x4359
-
-#define CYGETMON                0x435901
-#define CYGETTHRESH             0x435902
-#define CYSETTHRESH             0x435903
-#define CYGETDEFTHRESH          0x435904
-#define CYSETDEFTHRESH          0x435905
-#define CYGETTIMEOUT            0x435906
-#define CYSETTIMEOUT            0x435907
-#define CYGETDEFTIMEOUT         0x435908
-#define CYSETDEFTIMEOUT         0x435909
-#define CYSETRFLOW		0x43590a
-#define CYGETRFLOW		0x43590b
-#define CYSETRTSDTR_INV		0x43590c
-#define CYGETRTSDTR_INV		0x43590d
-#define CYZSETPOLLCYCLE		0x43590e
-#define CYZGETPOLLCYCLE		0x43590f
-#define CYGETCD1400VER		0x435910
-#define	CYSETWAIT		0x435912
-#define	CYGETWAIT		0x435913
-
-/*************** CYCLOM-Z ADDITIONS ***************/
-
-#define CZIOC           ('M' << 8)
-#define CZ_NBOARDS      (CZIOC|0xfa)
-#define CZ_BOOT_START   (CZIOC|0xfb)
-#define CZ_BOOT_DATA    (CZIOC|0xfc)
-#define CZ_BOOT_END     (CZIOC|0xfd)
-#define CZ_TEST         (CZIOC|0xfe)
-
-#define CZ_DEF_POLL	(HZ/25)
-
-#define MAX_BOARD       4       /* Max number of boards */
-#define MAX_DEV         256     /* Max number of ports total */
-#define	CYZ_MAX_SPEED	921600
-
-#define	CYZ_FIFO_SIZE	16
-
-#define CYZ_BOOT_NWORDS 0x100
-struct CYZ_BOOT_CTRL {
-        unsigned short  nboard;
-        int             status[MAX_BOARD];
-        int             nchannel[MAX_BOARD];
-        int             fw_rev[MAX_BOARD];
-        unsigned long   offset;
-        unsigned long   data[CYZ_BOOT_NWORDS];
-};
-
-
-#ifndef DP_WINDOW_SIZE
-/*
- *	Memory Window Sizes
- */
-
-#define	DP_WINDOW_SIZE		(0x00080000)	/* window size 512 Kb */
-#define	ZE_DP_WINDOW_SIZE	(0x00100000)	/* window size 1 Mb (Ze and
-						  8Zo V.2 */
-#define	CTRL_WINDOW_SIZE	(0x00000080)	/* runtime regs 128 bytes */
-
-/*
- *	CUSTOM_REG - Cyclom-Z/PCI Custom Registers Set. The driver
- *	normally will access only interested on the fpga_id, fpga_version,
- *	start_cpu and stop_cpu.
- */
-
-struct	CUSTOM_REG {
-	__u32	fpga_id;		/* FPGA Identification Register */
-	__u32	fpga_version;		/* FPGA Version Number Register */
-	__u32	cpu_start;		/* CPU start Register (write) */
-	__u32	cpu_stop;		/* CPU stop Register (write) */
-	__u32	misc_reg;		/* Miscellaneous Register */
-	__u32	idt_mode;		/* IDT mode Register */
-	__u32	uart_irq_status;	/* UART IRQ status Register */
-	__u32	clear_timer0_irq;	/* Clear timer interrupt Register */
-	__u32	clear_timer1_irq;	/* Clear timer interrupt Register */
-	__u32	clear_timer2_irq;	/* Clear timer interrupt Register */
-	__u32	test_register;		/* Test Register */
-	__u32	test_count;		/* Test Count Register */
-	__u32	timer_select;		/* Timer select register */
-	__u32	pr_uart_irq_status;	/* Prioritized UART IRQ stat Reg */
-	__u32	ram_wait_state;		/* RAM wait-state Register */
-	__u32	uart_wait_state;	/* UART wait-state Register */
-	__u32	timer_wait_state;	/* timer wait-state Register */
-	__u32	ack_wait_state;		/* ACK wait State Register */
-};
-
-/*
- *	RUNTIME_9060 - PLX PCI9060ES local configuration and shared runtime
- *	registers. This structure can be used to access the 9060 registers
- *	(memory mapped).
- */
-
-struct RUNTIME_9060 {
-	__u32	loc_addr_range;	/* 00h - Local Address Range */
-	__u32	loc_addr_base;	/* 04h - Local Address Base */
-	__u32	loc_arbitr;	/* 08h - Local Arbitration */
-	__u32	endian_descr;	/* 0Ch - Big/Little Endian Descriptor */
-	__u32	loc_rom_range;	/* 10h - Local ROM Range */
-	__u32	loc_rom_base;	/* 14h - Local ROM Base */
-	__u32	loc_bus_descr;	/* 18h - Local Bus descriptor */
-	__u32	loc_range_mst;	/* 1Ch - Local Range for Master to PCI */
-	__u32	loc_base_mst;	/* 20h - Local Base for Master PCI */
-	__u32	loc_range_io;	/* 24h - Local Range for Master IO */
-	__u32	pci_base_mst;	/* 28h - PCI Base for Master PCI */
-	__u32	pci_conf_io;	/* 2Ch - PCI configuration for Master IO */
-	__u32	filler1;	/* 30h */
-	__u32	filler2;	/* 34h */
-	__u32	filler3;	/* 38h */
-	__u32	filler4;	/* 3Ch */
-	__u32	mail_box_0;	/* 40h - Mail Box 0 */
-	__u32	mail_box_1;	/* 44h - Mail Box 1 */
-	__u32	mail_box_2;	/* 48h - Mail Box 2 */
-	__u32	mail_box_3;	/* 4Ch - Mail Box 3 */
-	__u32	filler5;	/* 50h */
-	__u32	filler6;	/* 54h */
-	__u32	filler7;	/* 58h */
-	__u32	filler8;	/* 5Ch */
-	__u32	pci_doorbell;	/* 60h - PCI to Local Doorbell */
-	__u32	loc_doorbell;	/* 64h - Local to PCI Doorbell */
-	__u32	intr_ctrl_stat;	/* 68h - Interrupt Control/Status */
-	__u32	init_ctrl;	/* 6Ch - EEPROM control, Init Control, etc */
-};
-
-/* Values for the Local Base Address re-map register */
-
-#define	WIN_RAM		0x00000001L	/* set the sliding window to RAM */
-#define	WIN_CREG	0x14000001L	/* set the window to custom Registers */
-
-/* Values timer select registers */
-
-#define	TIMER_BY_1M	0x00		/* clock divided by 1M */
-#define	TIMER_BY_256K	0x01		/* clock divided by 256k */
-#define	TIMER_BY_128K	0x02		/* clock divided by 128k */
-#define	TIMER_BY_32K	0x03		/* clock divided by 32k */
-
-/****************** ****************** *******************/
-#endif
-
-#ifndef ZFIRM_ID
-/* #include "zfwint.h" */
-/****************** ****************** *******************/
-/*
- *	This file contains the definitions for interfacing with the
- *	Cyclom-Z ZFIRM Firmware.
- */
-
-/* General Constant definitions */
-
-#define	MAX_CHAN	64		/* max number of channels per board */
-
-/* firmware id structure (set after boot) */
-
-#define ID_ADDRESS	0x00000180L	/* signature/pointer address */
-#define	ZFIRM_ID	0x5557465AL	/* ZFIRM/U signature */
-#define	ZFIRM_HLT	0x59505B5CL	/* ZFIRM needs external power supply */
-#define	ZFIRM_RST	0x56040674L	/* RST signal (due to FW reset) */
-
-#define	ZF_TINACT_DEF	1000		/* default inactivity timeout 
-					   (1000 ms) */
-#define	ZF_TINACT	ZF_TINACT_DEF
-
-struct	FIRM_ID {
-	__u32	signature;		/* ZFIRM/U signature */
-	__u32	zfwctrl_addr;		/* pointer to ZFW_CTRL structure */
-};
-
-/* Op. System id */
-
-#define	C_OS_LINUX	0x00000030	/* generic Linux system */
-
-/* channel op_mode */
-
-#define	C_CH_DISABLE	0x00000000	/* channel is disabled */
-#define	C_CH_TXENABLE	0x00000001	/* channel Tx enabled */
-#define	C_CH_RXENABLE	0x00000002	/* channel Rx enabled */
-#define	C_CH_ENABLE	0x00000003	/* channel Tx/Rx enabled */
-#define	C_CH_LOOPBACK	0x00000004	/* Loopback mode */
-
-/* comm_parity - parity */
-
-#define	C_PR_NONE	0x00000000	/* None */
-#define	C_PR_ODD	0x00000001	/* Odd */
-#define C_PR_EVEN	0x00000002	/* Even */
-#define C_PR_MARK	0x00000004	/* Mark */
-#define C_PR_SPACE	0x00000008	/* Space */
-#define C_PR_PARITY	0x000000ff
-
-#define	C_PR_DISCARD	0x00000100	/* discard char with frame/par error */
-#define C_PR_IGNORE	0x00000200	/* ignore frame/par error */
-
-/* comm_data_l - data length and stop bits */
-
-#define C_DL_CS5	0x00000001
-#define C_DL_CS6	0x00000002
-#define C_DL_CS7	0x00000004
-#define C_DL_CS8	0x00000008
-#define	C_DL_CS		0x0000000f
-#define C_DL_1STOP	0x00000010
-#define C_DL_15STOP	0x00000020
-#define C_DL_2STOP	0x00000040
-#define	C_DL_STOP	0x000000f0
-
-/* interrupt enabling/status */
-
-#define	C_IN_DISABLE	0x00000000	/* zero, disable interrupts */
-#define	C_IN_TXBEMPTY	0x00000001	/* tx buffer empty */
-#define	C_IN_TXLOWWM	0x00000002	/* tx buffer below LWM */
-#define	C_IN_RXHIWM	0x00000010	/* rx buffer above HWM */
-#define	C_IN_RXNNDT	0x00000020	/* rx no new data timeout */
-#define	C_IN_MDCD	0x00000100	/* modem DCD change */
-#define	C_IN_MDSR	0x00000200	/* modem DSR change */
-#define	C_IN_MRI	0x00000400	/* modem RI change */
-#define	C_IN_MCTS	0x00000800	/* modem CTS change */
-#define	C_IN_RXBRK	0x00001000	/* Break received */
-#define	C_IN_PR_ERROR	0x00002000	/* parity error */
-#define	C_IN_FR_ERROR	0x00004000	/* frame error */
-#define C_IN_OVR_ERROR  0x00008000      /* overrun error */
-#define C_IN_RXOFL	0x00010000      /* RX buffer overflow */
-#define C_IN_IOCTLW	0x00020000      /* I/O control w/ wait */
-#define C_IN_MRTS	0x00040000	/* modem RTS drop */
-#define C_IN_ICHAR	0x00080000
- 
-/* flow control */
-
-#define	C_FL_OXX	0x00000001	/* output Xon/Xoff flow control */
-#define	C_FL_IXX	0x00000002	/* output Xon/Xoff flow control */
-#define C_FL_OIXANY	0x00000004	/* output Xon/Xoff (any xon) */
-#define	C_FL_SWFLOW	0x0000000f
-
-/* flow status */
-
-#define	C_FS_TXIDLE	0x00000000	/* no Tx data in the buffer or UART */
-#define	C_FS_SENDING	0x00000001	/* UART is sending data */
-#define	C_FS_SWFLOW	0x00000002	/* Tx is stopped by received Xoff */
-
-/* rs_control/rs_status RS-232 signals */
-
-#define C_RS_PARAM	0x80000000	/* Indicates presence of parameter in 
-					   IOCTLM command */
-#define	C_RS_RTS	0x00000001	/* RTS */
-#define	C_RS_DTR	0x00000004	/* DTR */
-#define	C_RS_DCD	0x00000100	/* CD */
-#define	C_RS_DSR	0x00000200	/* DSR */
-#define	C_RS_RI		0x00000400	/* RI */
-#define	C_RS_CTS	0x00000800	/* CTS */
-
-/* commands Host <-> Board */
-
-#define	C_CM_RESET	0x01		/* reset/flush buffers */
-#define	C_CM_IOCTL	0x02		/* re-read CH_CTRL */
-#define	C_CM_IOCTLW	0x03		/* re-read CH_CTRL, intr when done */
-#define	C_CM_IOCTLM	0x04		/* RS-232 outputs change */
-#define	C_CM_SENDXOFF	0x10		/* send Xoff */
-#define	C_CM_SENDXON	0x11		/* send Xon */
-#define C_CM_CLFLOW	0x12		/* Clear flow control (resume) */
-#define	C_CM_SENDBRK	0x41		/* send break */
-#define	C_CM_INTBACK	0x42		/* Interrupt back */
-#define	C_CM_SET_BREAK	0x43		/* Tx break on */
-#define	C_CM_CLR_BREAK	0x44		/* Tx break off */
-#define	C_CM_CMD_DONE	0x45		/* Previous command done */
-#define C_CM_INTBACK2	0x46		/* Alternate Interrupt back */
-#define	C_CM_TINACT	0x51		/* set inactivity detection */
-#define	C_CM_IRQ_ENBL	0x52		/* enable generation of interrupts */
-#define	C_CM_IRQ_DSBL	0x53		/* disable generation of interrupts */
-#define	C_CM_ACK_ENBL	0x54		/* enable acknowledged interrupt mode */
-#define	C_CM_ACK_DSBL	0x55		/* disable acknowledged intr mode */
-#define	C_CM_FLUSH_RX	0x56		/* flushes Rx buffer */
-#define	C_CM_FLUSH_TX	0x57		/* flushes Tx buffer */
-#define C_CM_Q_ENABLE	0x58		/* enables queue access from the 
-					   driver */
-#define C_CM_Q_DISABLE  0x59            /* disables queue access from the 
-					   driver */
-
-#define	C_CM_TXBEMPTY	0x60		/* Tx buffer is empty */
-#define	C_CM_TXLOWWM	0x61		/* Tx buffer low water mark */
-#define	C_CM_RXHIWM	0x62		/* Rx buffer high water mark */
-#define	C_CM_RXNNDT	0x63		/* rx no new data timeout */
-#define	C_CM_TXFEMPTY	0x64
-#define	C_CM_ICHAR	0x65
-#define	C_CM_MDCD	0x70		/* modem DCD change */
-#define	C_CM_MDSR	0x71		/* modem DSR change */
-#define	C_CM_MRI	0x72		/* modem RI change */
-#define	C_CM_MCTS	0x73		/* modem CTS change */
-#define C_CM_MRTS	0x74		/* modem RTS drop */
-#define	C_CM_RXBRK	0x84		/* Break received */
-#define	C_CM_PR_ERROR	0x85		/* Parity error */
-#define	C_CM_FR_ERROR	0x86		/* Frame error */
-#define C_CM_OVR_ERROR  0x87            /* Overrun error */
-#define C_CM_RXOFL	0x88            /* RX buffer overflow */
-#define	C_CM_CMDERROR	0x90		/* command error */
-#define	C_CM_FATAL	0x91		/* fatal error */
-#define	C_CM_HW_RESET	0x92		/* reset board */
-
-/*
- *	CH_CTRL - This per port structure contains all parameters
- *	that control an specific port. It can be seen as the
- *	configuration registers of a "super-serial-controller".
- */
-
-struct CH_CTRL {
-	__u32	op_mode;	/* operation mode */
-	__u32	intr_enable;	/* interrupt masking */
-	__u32	sw_flow;	/* SW flow control */
-	__u32	flow_status;	/* output flow status */
-	__u32	comm_baud;	/* baud rate  - numerically specified */
-	__u32	comm_parity;	/* parity */
-	__u32	comm_data_l;	/* data length/stop */
-	__u32	comm_flags;	/* other flags */
-	__u32	hw_flow;	/* HW flow control */
-	__u32	rs_control;	/* RS-232 outputs */
-	__u32	rs_status;	/* RS-232 inputs */
-	__u32	flow_xon;	/* xon char */
-	__u32	flow_xoff;	/* xoff char */
-	__u32	hw_overflow;	/* hw overflow counter */
-	__u32	sw_overflow;	/* sw overflow counter */
-	__u32	comm_error;	/* frame/parity error counter */
-	__u32 ichar;
-	__u32 filler[7];
-};
-
-
-/*
- *	BUF_CTRL - This per channel structure contains
- *	all Tx and Rx buffer control for a given channel.
- */
-
-struct	BUF_CTRL	{
-	__u32	flag_dma;	/* buffers are in Host memory */
-	__u32	tx_bufaddr;	/* address of the tx buffer */
-	__u32	tx_bufsize;	/* tx buffer size */
-	__u32	tx_threshold;	/* tx low water mark */
-	__u32	tx_get;		/* tail index tx buf */
-	__u32	tx_put;		/* head index tx buf */
-	__u32	rx_bufaddr;	/* address of the rx buffer */
-	__u32	rx_bufsize;	/* rx buffer size */
-	__u32	rx_threshold;	/* rx high water mark */
-	__u32	rx_get;		/* tail index rx buf */
-	__u32	rx_put;		/* head index rx buf */
-	__u32	filler[5];	/* filler to align structures */
-};
-
-/*
- *	BOARD_CTRL - This per board structure contains all global 
- *	control fields related to the board.
- */
-
-struct BOARD_CTRL {
-
-	/* static info provided by the on-board CPU */
-	__u32	n_channel;	/* number of channels */
-	__u32	fw_version;	/* firmware version */
-
-	/* static info provided by the driver */
-	__u32	op_system;	/* op_system id */
-	__u32	dr_version;	/* driver version */
-
-	/* board control area */
-	__u32	inactivity;	/* inactivity control */
-
-	/* host to FW commands */
-	__u32	hcmd_channel;	/* channel number */
-	__u32	hcmd_param;	/* pointer to parameters */
-
-	/* FW to Host commands */
-	__u32	fwcmd_channel;	/* channel number */
-	__u32	fwcmd_param;	/* pointer to parameters */
-	__u32	zf_int_queue_addr; /* offset for INT_QUEUE structure */
-
-	/* filler so the structures are aligned */
-	__u32	filler[6];
-};
-
-/* Host Interrupt Queue */
-
-#define QUEUE_SIZE	(10*MAX_CHAN)
-
-struct	INT_QUEUE {
-	unsigned char	intr_code[QUEUE_SIZE];
-	unsigned long	channel[QUEUE_SIZE];
-	unsigned long	param[QUEUE_SIZE];
-	unsigned long	put;
-	unsigned long	get;
-};
-
-/*
- *	ZFW_CTRL - This is the data structure that includes all other
- *	data structures used by the Firmware.
- */
- 
-struct ZFW_CTRL {
-	struct BOARD_CTRL	board_ctrl;
-	struct CH_CTRL		ch_ctrl[MAX_CHAN];
-	struct BUF_CTRL		buf_ctrl[MAX_CHAN];
-};
-
-/****************** ****************** *******************/
-#endif
-
-#endif /* _UAPI_LINUX_CYCLADES_H */
diff --git a/include/uapi/linux/major.h b/include/uapi/linux/major.h
index 7e5fa8e15c43..4e5f2b3a3d54 100644
--- a/include/uapi/linux/major.h
+++ b/include/uapi/linux/major.h
@@ -34,8 +34,6 @@ 
 #define GOLDSTAR_CDROM_MAJOR	16
 #define OPTICS_CDROM_MAJOR	17
 #define SANYO_CDROM_MAJOR	18
-#define CYCLADES_MAJOR		19
-#define CYCLADESAUX_MAJOR	20
 #define MITSUMI_X_CDROM_MAJOR	20
 #define MFM_ACORN_MAJOR		21	/* ARM Linux /dev/mfm */
 #define SCSI_GENERIC_MAJOR	21
diff --git a/include/uapi/linux/serial.h b/include/uapi/linux/serial.h
index 93eb3c496ff1..fa6b16e5fdd8 100644
--- a/include/uapi/linux/serial.h
+++ b/include/uapi/linux/serial.h
@@ -52,11 +52,11 @@  struct serial_struct {
 #define PORT_16450	2
 #define PORT_16550	3
 #define PORT_16550A	4
-#define PORT_CIRRUS     5	/* usurped by cyclades.c */
+#define PORT_CIRRUS     5
 #define PORT_16650	6
 #define PORT_16650V2	7
 #define PORT_16750	8
-#define PORT_STARTECH	9	/* usurped by cyclades.c */
+#define PORT_STARTECH	9
 #define PORT_16C950	10	/* Oxford Semiconductor */
 #define PORT_16654	11
 #define PORT_16850	12