From: Lucas Tanure <tanureal@opensource.cirrus.com>
To: James Schulman <james.schulman@cirrus.com>,
David Rhodes <david.rhodes@cirrus.com>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>, Jaroslav Kysela <perex@perex.cz>,
Takashi Iwai <tiwai@suse.com>
Cc: <alsa-devel@alsa-project.org>, <linux-kernel@vger.kernel.org>,
<patches@opensource.cirrus.com>,
Lucas Tanure <tanureal@opensource.cirrus.com>
Subject: [PATCH v3 01/15] ASoC: cs42l42: Fix Bitclock polarity inversion
Date: Sat, 6 Mar 2021 18:55:39 +0000 [thread overview]
Message-ID: <20210306185553.62053-2-tanureal@opensource.cirrus.com> (raw)
In-Reply-To: <20210306185553.62053-1-tanureal@opensource.cirrus.com>
The driver was setting bit clock polarity opposite to intended polarity.
Also simplify the code by grouping ADC and DAC clock configurations into
a single field.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
---
Changes in v3:
- No changes
Changes in v2:
- No changes
sound/soc/codecs/cs42l42.c | 20 ++++++++------------
sound/soc/codecs/cs42l42.h | 11 ++++++-----
2 files changed, 14 insertions(+), 17 deletions(-)
diff --git a/sound/soc/codecs/cs42l42.c b/sound/soc/codecs/cs42l42.c
index 210fcbedf2413..df0d5fec0287a 100644
--- a/sound/soc/codecs/cs42l42.c
+++ b/sound/soc/codecs/cs42l42.c
@@ -797,27 +797,23 @@ static int cs42l42_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
/* Bitclock/frame inversion */
switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
case SND_SOC_DAIFMT_NB_NF:
+ asp_cfg_val |= CS42L42_ASP_SCPOL_NOR << CS42L42_ASP_SCPOL_SHIFT;
break;
case SND_SOC_DAIFMT_NB_IF:
- asp_cfg_val |= CS42L42_ASP_POL_INV <<
- CS42L42_ASP_LCPOL_IN_SHIFT;
+ asp_cfg_val |= CS42L42_ASP_SCPOL_NOR << CS42L42_ASP_SCPOL_SHIFT;
+ asp_cfg_val |= CS42L42_ASP_LCPOL_INV << CS42L42_ASP_LCPOL_SHIFT;
break;
case SND_SOC_DAIFMT_IB_NF:
- asp_cfg_val |= CS42L42_ASP_POL_INV <<
- CS42L42_ASP_SCPOL_IN_DAC_SHIFT;
break;
case SND_SOC_DAIFMT_IB_IF:
- asp_cfg_val |= CS42L42_ASP_POL_INV <<
- CS42L42_ASP_LCPOL_IN_SHIFT;
- asp_cfg_val |= CS42L42_ASP_POL_INV <<
- CS42L42_ASP_SCPOL_IN_DAC_SHIFT;
+ asp_cfg_val |= CS42L42_ASP_LCPOL_INV << CS42L42_ASP_LCPOL_SHIFT;
break;
}
- snd_soc_component_update_bits(component, CS42L42_ASP_CLK_CFG,
- CS42L42_ASP_MODE_MASK |
- CS42L42_ASP_SCPOL_IN_DAC_MASK |
- CS42L42_ASP_LCPOL_IN_MASK, asp_cfg_val);
+ snd_soc_component_update_bits(component, CS42L42_ASP_CLK_CFG, CS42L42_ASP_MODE_MASK |
+ CS42L42_ASP_SCPOL_MASK |
+ CS42L42_ASP_LCPOL_MASK,
+ asp_cfg_val);
return 0;
}
diff --git a/sound/soc/codecs/cs42l42.h b/sound/soc/codecs/cs42l42.h
index 9e3cc528dcff0..1f0d67c95a9ad 100644
--- a/sound/soc/codecs/cs42l42.h
+++ b/sound/soc/codecs/cs42l42.h
@@ -258,11 +258,12 @@
#define CS42L42_ASP_SLAVE_MODE 0x00
#define CS42L42_ASP_MODE_SHIFT 4
#define CS42L42_ASP_MODE_MASK (1 << CS42L42_ASP_MODE_SHIFT)
-#define CS42L42_ASP_SCPOL_IN_DAC_SHIFT 2
-#define CS42L42_ASP_SCPOL_IN_DAC_MASK (1 << CS42L42_ASP_SCPOL_IN_DAC_SHIFT)
-#define CS42L42_ASP_LCPOL_IN_SHIFT 0
-#define CS42L42_ASP_LCPOL_IN_MASK (1 << CS42L42_ASP_LCPOL_IN_SHIFT)
-#define CS42L42_ASP_POL_INV 1
+#define CS42L42_ASP_SCPOL_SHIFT 2
+#define CS42L42_ASP_SCPOL_MASK (3 << CS42L42_ASP_SCPOL_SHIFT)
+#define CS42L42_ASP_SCPOL_NOR 3
+#define CS42L42_ASP_LCPOL_SHIFT 0
+#define CS42L42_ASP_LCPOL_MASK (3 << CS42L42_ASP_LCPOL_SHIFT)
+#define CS42L42_ASP_LCPOL_INV 3
#define CS42L42_ASP_FRM_CFG (CS42L42_PAGE_12 + 0x08)
#define CS42L42_ASP_STP_SHIFT 4
--
2.30.1
next prev parent reply other threads:[~2021-03-06 19:12 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-06 18:55 [PATCH v3 00/15] Report jack and button detection + Capture Support Lucas Tanure
2021-03-06 18:55 ` Lucas Tanure [this message]
2021-03-06 18:55 ` [PATCH v3 02/15] ASoC: cs42l42: Fix channel width support Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 03/15] ASoC: cs42l42: Fix mixer volume control Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 04/15] ASoC: cs42l42: Don't enable/disable regulator at Bias Level Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 05/15] ASoC: cs42l42: Always wait at least 3ms after reset Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 06/15] ASoC: cs42l42: Remove power if the driver is being removed Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 07/15] ASoC: cs42l42: Disable regulators if probe fails Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 08/15] ASoC: cs42l42: Provide finer control on playback path Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 09/15] ASoC: cs42l42: Set clock source for both ways of stream Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 10/15] ASoC: cs42l42: Add Capture Support Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 11/15] ASoC: cs42l42: Report jack and button detection Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 12/15] ASoC: cs42l42: Use bclk from hw_params if set_sysclk was not called Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 13/15] ASoC: cs42l42: Wait at least 150us after writing SCLK_PRESENT Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 14/15] ASoC: cs42l42: Only start PLL if it is needed Lucas Tanure
2021-03-06 18:55 ` [PATCH v3 15/15] ASoC: cs42l42: Wait for PLL to lock before switching to it Lucas Tanure
2021-03-09 19:06 ` (subset) [PATCH v3 00/15] Report jack and button detection + Capture Support Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210306185553.62053-2-tanureal@opensource.cirrus.com \
--to=tanureal@opensource.cirrus.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=david.rhodes@cirrus.com \
--cc=james.schulman@cirrus.com \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@opensource.cirrus.com \
--cc=perex@perex.cz \
--cc=tiwai@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).