From: Geert Uytterhoeven <geert@linux-m68k.org>
To: Linus Torvalds <torvalds@transmeta.com>
Cc: Linux Kernel Development <linux-kernel@vger.kernel.org>,
Geert Uytterhoeven <geert@linux-m68k.org>
Subject: [PATCH] M68k SCSI driver updates
Date: Wed, 19 Mar 2003 13:27:42 +0100 (MET) [thread overview]
Message-ID: <200303191227.h2JCRg200889@vervain.sonytel.be> (raw)
M68k SCSI drivers: update for the changes in 2.5.60:
o Replace `->lun' by `->device->lun'
o Replace `->target' by `->device->id'
o Replace `->host' by `->device->host'
--- linux-2.5.x/drivers/scsi/NCR53C9x.c Sun Mar 2 17:39:02 2003
+++ linux-m68k-2.5.x/drivers/scsi/NCR53C9x.c Fri Feb 14 13:25:53 2003
@@ -1099,7 +1099,7 @@
* disconnect.
*/
ESPMISC(("esp: Selecting device for first time. target=%d "
- "lun=%d\n", target, SCptr->lun));
+ "lun=%d\n", target, SCptr->device->lun));
if(!SDptr->borken && !esp_dev->disconnect)
esp_dev->disconnect = 1;
@@ -1173,7 +1173,7 @@
if(((SDptr->scsi_level < 3) && (SDptr->type != TYPE_TAPE)) ||
toshiba_cdrom_hwbug_wkaround || SDptr->borken) {
ESPMISC((KERN_INFO "esp%d: Disabling DISCONNECT for target %d "
- "lun %d\n", esp->esp_id, SCptr->target, SCptr->lun));
+ "lun %d\n", esp->esp_id, SCptr->device->id, SCptr->device->lun));
esp_dev->disconnect = 0;
*cmdp++ = IDENTIFY(0, lun);
} else {
@@ -1255,8 +1255,8 @@
esp->dma_led_on(esp);
/* We use the scratch area. */
- ESPQUEUE(("esp_queue: target=%d lun=%d ", SCpnt->target, SCpnt->lun));
- ESPDISC(("N<%02x,%02x>", SCpnt->target, SCpnt->lun));
+ ESPQUEUE(("esp_queue: target=%d lun=%d ", SCpnt->device->id, SCpnt->lun));
+ ESPDISC(("N<%02x,%02x>", SCpnt->device->id, SCpnt->lun));
esp_get_dmabufs(esp, SCpnt);
esp_save_pointers(esp, SCpnt); /* FIXME for tag queueing */
@@ -2235,7 +2235,7 @@
* state.
*/
ESPMISC(("esp: Status <%d> for target %d lun %d\n",
- SCptr->SCp.Status, SCptr->target, SCptr->lun));
+ SCptr->SCp.Status, SCptr->device->id, SCptr->device->lun));
/* But don't do this when spinning up a disk at
* boot time while we poll for completion as it
@@ -2246,14 +2246,14 @@
if(esp_should_clear_sync(SCptr) != 0)
esp_dev->sync = 0;
}
- ESPDISC(("F<%02x,%02x>", SCptr->target, SCptr->lun));
+ ESPDISC(("F<%02x,%02x>", SCptr->device->id, SCptr->device->lun));
esp_done(esp, ((SCptr->SCp.Status & 0xff) |
((SCptr->SCp.Message & 0xff)<<8) |
(DID_OK << 16)));
} else if(esp->prevmsgin == DISCONNECT) {
/* Normal disconnect. */
esp_cmd(esp, eregs, ESP_CMD_ESEL);
- ESPDISC(("D<%02x,%02x>", SCptr->target, SCptr->lun));
+ ESPDISC(("D<%02x,%02x>", SCptr->device->id, SCptr->device->lun));
append_SC(&esp->disconnected_SC, SCptr);
esp->current_SC = NULL;
if(esp->issue_SC)
@@ -2811,7 +2811,7 @@
/* Else, there really isn't anyone there. */
ESPMISC(("esp: selection failure, maybe nobody there?\n"));
ESPMISC(("esp: target %d lun %d\n",
- SCptr->target, SCptr->lun));
+ SCptr->device->id, SCptr->device->lun));
esp_done(esp, (DID_BAD_TARGET << 16));
}
return do_intr_end;
@@ -3084,7 +3084,7 @@
ESPSDTR(("soff=%2x stp=%2x cfg3=%2x\n",
esp_dev->sync_max_offset,
esp_dev->sync_min_period,
- esp->config3[SCptr->target]));
+ esp->config3[SCptr->device->id]));
esp->snip = 0;
} else if(esp_dev->sync_max_offset) {
--- linux-2.5.x/drivers/scsi/53c7xx.c Wed Feb 12 12:31:26 2003
+++ linux-m68k-2.5.x/drivers/scsi/53c7xx.c Thu Feb 13 16:12:27 2003
@@ -1759,7 +1759,7 @@
static void
NCR53c7xx_dsa_fixup (struct NCR53c7x0_cmd *cmd) {
Scsi_Cmnd *c = cmd->cmd;
- struct Scsi_Host *host = c->host;
+ struct Scsi_Host *host = c->device->host;
struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
host->hostdata[0];
int i;
@@ -1784,18 +1784,18 @@
*/
patch_abs_tci_data (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_lun, c->lun);
+ dsa_temp_lun, c->device->lun);
patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
dsa_temp_addr_next, virt_to_bus(&cmd->dsa_next_addr));
patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
dsa_temp_next, virt_to_bus(cmd->dsa) + Ent_dsa_zero -
Ent_dsa_code_template + A_dsa_next);
patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_sync, virt_to_bus((void *)hostdata->sync[c->target].script));
+ dsa_temp_sync, virt_to_bus((void *)hostdata->sync[c->device->id].script));
patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_sscf_710, virt_to_bus((void *)&hostdata->sync[c->target].sscf_710));
+ dsa_sscf_710, virt_to_bus((void *)&hostdata->sync[c->device->id].sscf_710));
patch_abs_tci_data (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_target, 1 << c->target);
+ dsa_temp_target, 1 << c->device->id);
/* XXX - new pointer stuff */
patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
dsa_temp_addr_saved_pointer, virt_to_bus(&cmd->saved_data_pointer));
@@ -1856,7 +1856,7 @@
static void
abnormal_finished (struct NCR53c7x0_cmd *cmd, int result) {
Scsi_Cmnd *c = cmd->cmd;
- struct Scsi_Host *host = c->host;
+ struct Scsi_Host *host = c->device->host;
struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
host->hostdata[0];
unsigned long flags;
@@ -1940,7 +1940,7 @@
host->host_no, c->pid);
else if (linux_search) {
*linux_prev = linux_search->next;
- --hostdata->busy[c->target][c->lun];
+ --hostdata->busy[c->device->id][c->device->lun];
}
/* Return the NCR command structure to the free list */
@@ -2287,9 +2287,9 @@
hostdata->dsp_changed = 1;
if (cmd && (cmd->flags & CMD_FLAG_SDTR)) {
printk ("scsi%d : target %d rejected SDTR\n", host->host_no,
- c->target);
+ c->device->id);
cmd->flags &= ~CMD_FLAG_SDTR;
- asynchronous (host, c->target);
+ asynchronous (host, c->device->id);
print = 0;
}
break;
@@ -2311,7 +2311,7 @@
if (print) {
printk ("scsi%d : received message", host->host_no);
if (c)
- printk (" from target %d lun %d ", c->target, c->lun);
+ printk (" from target %d lun %d ", c->device->id, c->device->lun);
print_msg ((unsigned char *) hostdata->msg_buf);
printk("\n");
}
@@ -2331,7 +2331,7 @@
if (cmd) {
char buf[80];
- sprintf (buf, "scsi%d : target %d %s ", host->host_no, c->target,
+ sprintf (buf, "scsi%d : target %d %s ", host->host_no, c->device->id,
(cmd->flags & CMD_FLAG_SDTR) ? "accepting" : "requesting");
print_synchronous (buf, (unsigned char *) hostdata->msg_buf);
@@ -2346,10 +2346,10 @@
if (cmd->flags & CMD_FLAG_SDTR) {
cmd->flags &= ~CMD_FLAG_SDTR;
if (hostdata->msg_buf[4])
- synchronous (host, c->target, (unsigned char *)
+ synchronous (host, c->device->id, (unsigned char *)
hostdata->msg_buf);
else
- asynchronous (host, c->target);
+ asynchronous (host, c->device->id);
hostdata->dsp = hostdata->script + hostdata->E_accept_message /
sizeof(u32);
hostdata->dsp_changed = 1;
@@ -2357,11 +2357,11 @@
} else {
if (hostdata->options & OPTION_SYNCHRONOUS) {
cmd->flags |= CMD_FLAG_DID_SDTR;
- synchronous (host, c->target, (unsigned char *)
+ synchronous (host, c->device->id, (unsigned char *)
hostdata->msg_buf);
} else {
hostdata->msg_buf[4] = 0; /* 0 offset = async */
- asynchronous (host, c->target);
+ asynchronous (host, c->device->id);
}
patch_dsa_32 (cmd->dsa, dsa_msgout_other, 0, 5);
patch_dsa_32 (cmd->dsa, dsa_msgout_other, 1, (u32)
@@ -2545,9 +2545,9 @@
host->host_no, NCR53c7x0_read8(SXFER_REG));
if (c) {
print_insn (host, (u32 *)
- hostdata->sync[c->target].script, "", 1);
+ hostdata->sync[c->device->id].script, "", 1);
print_insn (host, (u32 *)
- hostdata->sync[c->target].script + 2, "", 1);
+ hostdata->sync[c->device->id].script + 2, "", 1);
}
}
return SPECIFIC_INT_RESTART;
@@ -2658,7 +2658,7 @@
if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
if (c)
printk("scsi%d : target %d lun %d disconnecting\n",
- host->host_no, c->target, c->lun);
+ host->host_no, c->device->id, c->device->lun);
else
printk("scsi%d : unknown target disconnecting\n",
host->host_no);
@@ -2680,9 +2680,9 @@
#endif
if (c) {
print_insn (host, (u32 *)
- hostdata->sync[c->target].script, "", 1);
+ hostdata->sync[c->device->id].script, "", 1);
print_insn (host, (u32 *)
- hostdata->sync[c->target].script + 2, "", 1);
+ hostdata->sync[c->device->id].script + 2, "", 1);
}
}
return SPECIFIC_INT_RESTART;
@@ -2734,8 +2734,8 @@
if ((hostdata->chip / 100) == 8) {
scntl3 = NCR53c7x0_read8 (SCNTL3_REG_800);
if (c) {
- if (sxfer != hostdata->sync[c->target].sxfer_sanity ||
- scntl3 != hostdata->sync[c->target].scntl3_sanity) {
+ if (sxfer != hostdata->sync[c->device->id].sxfer_sanity ||
+ scntl3 != hostdata->sync[c->device->id].scntl3_sanity) {
printk ("scsi%d : sync sanity check failed sxfer=0x%x, scntl3=0x%x",
host->host_no, sxfer, scntl3);
NCR53c7x0_write8 (SXFER_REG, sxfer);
@@ -2746,12 +2746,12 @@
host->host_no, (int) sxfer, (int) scntl3);
} else {
if (c) {
- if (sxfer != hostdata->sync[c->target].sxfer_sanity) {
+ if (sxfer != hostdata->sync[c->device->id].sxfer_sanity) {
printk ("scsi%d : sync sanity check failed sxfer=0x%x",
host->host_no, sxfer);
NCR53c7x0_write8 (SXFER_REG, sxfer);
NCR53c7x0_write8 (SBCL_REG,
- hostdata->sync[c->target].sscf_710);
+ hostdata->sync[c->device->id].sscf_710);
}
} else
printk ("scsi%d : unknown command sxfer=0x%x\n",
@@ -2807,9 +2807,9 @@
(DCMD_REG)) == hostdata->script +
Ent_select_check_dsa / sizeof(u32) ?
"selection" : "reselection";
- if (c && sdid != c->target) {
+ if (c && sdid != c->device->id) {
printk ("scsi%d : SDID target %d != DSA target %d at %s\n",
- host->host_no, sdid, c->target, where);
+ host->host_no, sdid, c->device->id, where);
print_lots(host);
dump_events (host, 20);
return SPECIFIC_INT_PANIC;
@@ -2855,7 +2855,7 @@
if (event->event == EVENT_RESELECT)
event->lun = hostdata->reselected_identify & 0xf;
else if (c)
- event->lun = c->lun;
+ event->lun = c->device->lun;
else
event->lun = 255;
do_gettimeofday(&(event->time));
@@ -3049,7 +3049,7 @@
static struct NCR53c7x0_cmd *
allocate_cmd (Scsi_Cmnd *cmd) {
- struct Scsi_Host *host = cmd->host;
+ struct Scsi_Host *host = cmd->device->host;
struct NCR53c7x0_hostdata *hostdata =
(struct NCR53c7x0_hostdata *) host->hostdata[0];
u32 real; /* Real address */
@@ -3061,8 +3061,8 @@
printk ("scsi%d : num_cmds = %d, can_queue = %d\n"
" target = %d, lun = %d, %s\n",
host->host_no, hostdata->num_cmds, host->can_queue,
- cmd->target, cmd->lun, (hostdata->cmd_allocated[cmd->target] &
- (1 << cmd->lun)) ? "already allocated" : "not allocated");
+ cmd->device->id, cmd->device->lun, (hostdata->cmd_allocated[cmd->device->id] &
+ (1 << cmd->device->lun)) ? "already allocated" : "not allocated");
/*
* If we have not yet reserved commands for this I_T_L nexus, and
@@ -3070,11 +3070,11 @@
* being allocated under 1.3.x, or being outside of scan_scsis in
* 1.2.x), do so now.
*/
- if (!(hostdata->cmd_allocated[cmd->target] & (1 << cmd->lun)) &&
+ if (!(hostdata->cmd_allocated[cmd->device->id] & (1 << cmd->device->lun)) &&
cmd->device && cmd->device->has_cmdblocks) {
if ((hostdata->extra_allocate + hostdata->num_cmds) < host->can_queue)
hostdata->extra_allocate += host->cmd_per_lun;
- hostdata->cmd_allocated[cmd->target] |= (1 << cmd->lun);
+ hostdata->cmd_allocated[cmd->device->id] |= (1 << cmd->device->lun);
}
for (; hostdata->extra_allocate > 0 ; --hostdata->extra_allocate,
@@ -3130,7 +3130,7 @@
local_irq_restore(flags);
if (!tmp)
printk ("scsi%d : can't allocate command for target %d lun %d\n",
- host->host_no, cmd->target, cmd->lun);
+ host->host_no, cmd->device->id, cmd->device->lun);
return tmp;
}
@@ -3150,7 +3150,7 @@
static struct NCR53c7x0_cmd *
create_cmd (Scsi_Cmnd *cmd) {
NCR53c7x0_local_declare();
- struct Scsi_Host *host = cmd->host;
+ struct Scsi_Host *host = cmd->device->host;
struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
host->hostdata[0];
struct NCR53c7x0_cmd *tmp; /* NCR53c7x0_cmd structure for this command */
@@ -3166,7 +3166,7 @@
#endif
unsigned long flags;
u32 exp_select_indirect; /* Used in sanity check */
- NCR53c7x0_local_setup(cmd->host);
+ NCR53c7x0_local_setup(cmd->device->host);
if (!(tmp = allocate_cmd (cmd)))
return NULL;
@@ -3322,45 +3322,45 @@
if (hostdata->options & OPTION_DEBUG_SYNCHRONOUS) {
- exp_select_indirect = ((1 << cmd->target) << 16) |
- (hostdata->sync[cmd->target].sxfer_sanity << 8);
+ exp_select_indirect = ((1 << cmd->device->id) << 16) |
+ (hostdata->sync[cmd->device->id].sxfer_sanity << 8);
- if (hostdata->sync[cmd->target].select_indirect !=
+ if (hostdata->sync[cmd->device->id].select_indirect !=
exp_select_indirect) {
printk ("scsi%d : sanity check failed select_indirect=0x%x\n",
- host->host_no, hostdata->sync[cmd->target].select_indirect);
+ host->host_no, hostdata->sync[cmd->device->id].select_indirect);
FATAL(host);
}
}
patch_dsa_32(tmp->dsa, dsa_select, 0,
- hostdata->sync[cmd->target].select_indirect);
+ hostdata->sync[cmd->device->id].select_indirect);
/*
* Right now, we'll do the WIDE and SYNCHRONOUS negotiations on
* different commands; although it should be trivial to do them
* both at the same time.
*/
- if (hostdata->initiate_wdtr & (1 << cmd->target)) {
+ if (hostdata->initiate_wdtr & (1 << cmd->device->id)) {
memcpy ((void *) (tmp->select + 1), (void *) wdtr_message,
sizeof(wdtr_message));
patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1 + sizeof(wdtr_message));
local_irq_save(flags);
- hostdata->initiate_wdtr &= ~(1 << cmd->target);
+ hostdata->initiate_wdtr &= ~(1 << cmd->device->id);
local_irq_restore(flags);
- } else if (hostdata->initiate_sdtr & (1 << cmd->target)) {
+ } else if (hostdata->initiate_sdtr & (1 << cmd->device->id)) {
memcpy ((void *) (tmp->select + 1), (void *) sdtr_message,
sizeof(sdtr_message));
patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1 + sizeof(sdtr_message));
tmp->flags |= CMD_FLAG_SDTR;
local_irq_save(flags);
- hostdata->initiate_sdtr &= ~(1 << cmd->target);
+ hostdata->initiate_sdtr &= ~(1 << cmd->device->id);
local_irq_restore(flags);
}
#if 1
- else if (!(hostdata->talked_to & (1 << cmd->target)) &&
+ else if (!(hostdata->talked_to & (1 << cmd->device->id)) &&
!(hostdata->options & OPTION_NO_ASYNC)) {
memcpy ((void *) (tmp->select + 1), (void *) async_message,
@@ -3372,9 +3372,9 @@
else
patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1);
- hostdata->talked_to |= (1 << cmd->target);
+ hostdata->talked_to |= (1 << cmd->device->id);
tmp->select[0] = (hostdata->options & OPTION_DISCONNECT) ?
- IDENTIFY (1, cmd->lun) : IDENTIFY (0, cmd->lun);
+ IDENTIFY (1, cmd->device->lun) : IDENTIFY (0, cmd->device->lun);
patch_dsa_32(tmp->dsa, dsa_msgout, 1, virt_to_bus(tmp->select));
patch_dsa_32(tmp->dsa, dsa_cmdout, 0, cmd->cmd_len);
patch_dsa_32(tmp->dsa, dsa_cmdout, 1, virt_to_bus(tmp->cmnd));
@@ -3591,7 +3591,7 @@
int
NCR53c7xx_queue_command (Scsi_Cmnd *cmd, void (* done)(Scsi_Cmnd *)) {
- struct Scsi_Host *host = cmd->host;
+ struct Scsi_Host *host = cmd->device->host;
struct NCR53c7x0_hostdata *hostdata =
(struct NCR53c7x0_hostdata *) host->hostdata[0];
unsigned long flags;
@@ -3604,9 +3604,9 @@
#ifdef VALID_IDS
/* Ignore commands on invalid IDs */
- if (!hostdata->valid_ids[cmd->target]) {
+ if (!hostdata->valid_ids[cmd->device->id]) {
printk("scsi%d : ignoring target %d lun %d\n", host->host_no,
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
cmd->result = (DID_BAD_TARGET << 16);
done(cmd);
return 0;
@@ -3616,16 +3616,16 @@
local_irq_save(flags);
if ((hostdata->options & (OPTION_DEBUG_INIT_ONLY|OPTION_DEBUG_PROBE_ONLY))
|| ((hostdata->options & OPTION_DEBUG_TARGET_LIMIT) &&
- !(hostdata->debug_lun_limit[cmd->target] & (1 << cmd->lun)))
+ !(hostdata->debug_lun_limit[cmd->device->id] & (1 << cmd->device->lun)))
#ifdef LINUX_1_2
- || cmd->target > 7
+ || cmd->device->id > 7
#else
- || cmd->target > host->max_id
+ || cmd->device->id > host->max_id
#endif
- || cmd->target == host->this_id
+ || cmd->device->id == host->this_id
|| hostdata->state == STATE_DISABLED) {
printk("scsi%d : disabled or bad target %d lun %d\n", host->host_no,
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
cmd->result = (DID_BAD_TARGET << 16);
done(cmd);
local_irq_restore(flags);
@@ -3738,7 +3738,7 @@
--i, ncrcurrent += 2 /* JUMP instructions are two words */);
if (i > 0) {
- ++hostdata->busy[tmp->target][tmp->lun];
+ ++hostdata->busy[tmp->device->id][tmp->device->lun];
cmd->next = hostdata->running_list;
hostdata->running_list = cmd;
@@ -3799,7 +3799,7 @@
/* FIXME : in the future, this needs to accommodate SCSI-II tagged
queuing, and we may be able to play with fairness here a bit.
*/
- return hostdata->busy[cmd->target][cmd->lun];
+ return hostdata->busy[cmd->device->id][cmd->device->lun];
}
/*
@@ -3873,7 +3873,7 @@
if (tmp->host_scribble) {
if (hostdata->options & OPTION_DEBUG_QUEUES)
printk ("scsi%d : moving command for target %d lun %d to start list\n",
- host->host_no, tmp->target, tmp->lun);
+ host->host_no, tmp->device->id, tmp->device->lun);
to_schedule_list (host, hostdata,
@@ -3937,7 +3937,7 @@
printk ("scsi%d : Selection Timeout\n", host->host_no);
if (cmd) {
printk("scsi%d : target %d, lun %d, command ",
- host->host_no, cmd->cmd->target, cmd->cmd->lun);
+ host->host_no, cmd->cmd->device->id, cmd->cmd->device->lun);
print_command (cmd->cmd->cmnd);
printk("scsi%d : dsp = 0x%x (virt 0x%p)\n", host->host_no,
NCR53c7x0_read32(DSP_REG),
@@ -3975,7 +3975,7 @@
fatal = 1;
if (cmd) {
printk("scsi%d : target %d lun %d unexpected disconnect\n",
- host->host_no, cmd->cmd->target, cmd->cmd->lun);
+ host->host_no, cmd->cmd->device->id, cmd->cmd->device->lun);
print_lots (host);
abnormal_finished(cmd, DID_ERROR << 16);
} else
@@ -3991,7 +3991,7 @@
fatal = 1;
if (cmd && cmd->cmd) {
printk("scsi%d : target %d lun %d parity error.\n",
- host->host_no, cmd->cmd->target, cmd->cmd->lun);
+ host->host_no, cmd->cmd->device->id, cmd->cmd->device->lun);
abnormal_finished (cmd, DID_PARITY << 16);
} else
printk("scsi%d : parity error\n", host->host_no);
@@ -4199,7 +4199,7 @@
if (cmd_prev_ptr)
*cmd_prev_ptr = (struct NCR53c7x0_cmd *) cmd->next;
- --hostdata->busy[tmp->target][tmp->lun];
+ --hostdata->busy[tmp->device->id][tmp->device->lun];
cmd->next = hostdata->free;
hostdata->free = cmd;
@@ -4207,7 +4207,7 @@
if (hostdata->options & OPTION_DEBUG_INTR) {
printk ("scsi%d : command complete : pid %lu, id %d,lun %d result 0x%x ",
- host->host_no, tmp->pid, tmp->target, tmp->lun, tmp->result);
+ host->host_no, tmp->pid, tmp->device->id, tmp->device->lun, tmp->result);
print_command (tmp->cmnd);
}
@@ -4292,8 +4292,8 @@
if (hostdata->options & OPTION_DEBUG_INTR) {
if (cmd) {
printk("scsi%d : interrupt for pid %lu, id %d, lun %d ",
- host->host_no, cmd->cmd->pid, (int) cmd->cmd->target,
- (int) cmd->cmd->lun);
+ host->host_no, cmd->cmd->pid, (int) cmd->cmd->device->id,
+ (int) cmd->cmd->device->lun);
print_command (cmd->cmd->cmnd);
} else {
printk("scsi%d : no active command\n", host->host_no);
@@ -4671,7 +4671,7 @@
hostdata->dsp = dsp + 2 /* two _words_ */;
hostdata->dsp_changed = 1;
printk ("scsi%d : target %d ignored SDTR and went into COMMAND OUT\n",
- host->host_no, cmd->cmd->target);
+ host->host_no, cmd->cmd->device->id);
cmd->flags &= ~CMD_FLAG_SDTR;
action = ACTION_CONTINUE;
break;
@@ -5136,7 +5136,7 @@
int
NCR53c7xx_abort (Scsi_Cmnd *cmd) {
NCR53c7x0_local_declare();
- struct Scsi_Host *host = cmd->host;
+ struct Scsi_Host *host = cmd->device->host;
struct NCR53c7x0_hostdata *hostdata = host ? (struct NCR53c7x0_hostdata *)
host->hostdata[0] : NULL;
unsigned long flags;
@@ -5242,7 +5242,7 @@
return SCSI_ABORT_NOT_RUNNING;
} else {
printk ("scsi%d : DANGER : command running, can not abort.\n",
- cmd->host->host_no);
+ cmd->device->host->host_no);
local_irq_restore(flags);
return SCSI_ABORT_BUSY;
}
@@ -5273,7 +5273,7 @@
* command was ever counted as BUSY, so if we end up here we can
* decrement the busy count if and only if it is necessary.
*/
- --hostdata->busy[cmd->target][cmd->lun];
+ --hostdata->busy[cmd->device->id][cmd->device->lun];
}
local_irq_restore(flags);
cmd->scsi_done(cmd);
@@ -5318,7 +5318,7 @@
* each command.
*/
Scsi_Cmnd *nuke_list = NULL;
- struct Scsi_Host *host = cmd->host;
+ struct Scsi_Host *host = cmd->device->host;
struct NCR53c7x0_hostdata *hostdata =
(struct NCR53c7x0_hostdata *) host->hostdata[0];
@@ -5388,7 +5388,7 @@
static int
insn_to_offset (Scsi_Cmnd *cmd, u32 *insn) {
struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) cmd->host->hostdata[0];
+ (struct NCR53c7x0_hostdata *) cmd->device->host->hostdata[0];
struct NCR53c7x0_cmd *ncmd =
(struct NCR53c7x0_cmd *) cmd->host_scribble;
int offset = 0, buffers;
@@ -5418,7 +5418,7 @@
--buffers, offset += segment->length, ++segment)
#if 0
printk("scsi%d: comparing 0x%p to 0x%p\n",
- cmd->host->host_no, saved, page_address(segment->page+segment->offset);
+ cmd->device->host->host_no, saved, page_address(segment->page+segment->offset);
#else
;
#endif
@@ -5456,7 +5456,7 @@
int offset, i;
char *where;
u32 *ptr;
- NCR53c7x0_local_setup (cmd->host);
+ NCR53c7x0_local_setup (cmd->device->host);
if (check_address ((unsigned long) ncmd,sizeof (struct NCR53c7x0_cmd)) == 0)
{
@@ -5484,15 +5484,15 @@
if (offset != -1)
printk ("scsi%d : %s data pointer at offset %d\n",
- cmd->host->host_no, where, offset);
+ cmd->device->host->host_no, where, offset);
else {
int size;
printk ("scsi%d : can't determine %s data pointer offset\n",
- cmd->host->host_no, where);
+ cmd->device->host->host_no, where);
if (ncmd) {
- size = print_insn (cmd->host,
+ size = print_insn (cmd->device->host,
bus_to_virt(ncmd->saved_data_pointer), "", 1);
- print_insn (cmd->host,
+ print_insn (cmd->device->host,
bus_to_virt(ncmd->saved_data_pointer) + size * sizeof(u32),
"", 1);
}
@@ -5549,7 +5549,7 @@
/* XXX Maybe we should access cmd->host_scribble->result here. RGH */
if (cmd) {
printk(" result = 0x%x, target = %d, lun = %d, cmd = ",
- cmd->result, cmd->target, cmd->lun);
+ cmd->result, cmd->device->id, cmd->device->lun);
print_command(cmd->cmnd);
} else
printk("\n");
@@ -5558,11 +5558,11 @@
if (cmd) {
printk("scsi%d target %d : sxfer_sanity = 0x%x, scntl3_sanity = 0x%x\n"
" script : ",
- host->host_no, cmd->target,
- hostdata->sync[cmd->target].sxfer_sanity,
- hostdata->sync[cmd->target].scntl3_sanity);
- for (i = 0; i < (sizeof(hostdata->sync[cmd->target].script) / 4); ++i)
- printk ("0x%x ", hostdata->sync[cmd->target].script[i]);
+ host->host_no, cmd->device->id,
+ hostdata->sync[cmd->device->id].sxfer_sanity,
+ hostdata->sync[cmd->device->id].scntl3_sanity);
+ for (i = 0; i < (sizeof(hostdata->sync[cmd->device->id].script) / 4); ++i)
+ printk ("0x%x ", hostdata->sync[cmd->device->id].script[i]);
printk ("\n");
print_progress (cmd);
}
@@ -5604,7 +5604,7 @@
-> dsa, "");
} else
printk ("scsi%d : scsi pid %ld for target %d lun %d has no NCR53c7x0_cmd\n",
- host->host_no, cmd->pid, cmd->target, cmd->lun);
+ host->host_no, cmd->pid, cmd->device->id, cmd->device->lun);
local_irq_restore(flags);
}
--- linux-2.5.x/drivers/scsi/a2091.c Wed Nov 20 11:36:29 2002
+++ linux-m68k-2.5.x/drivers/scsi/a2091.c Thu Feb 13 16:14:20 2003
@@ -52,7 +52,7 @@
{
unsigned short cntr = CNTR_PDMD | CNTR_INTEN;
unsigned long addr = virt_to_bus(cmd->SCp.ptr);
- struct Scsi_Host *instance = cmd->host;
+ struct Scsi_Host *instance = cmd->device->host;
/* don't allow DMA if the physical address is bad */
if (addr & A2091_XFER_MASK ||
@@ -102,12 +102,12 @@
cntr |= CNTR_DDIR;
/* remember direction */
- HDATA(cmd->host)->dma_dir = dir_in;
+ HDATA(cmd->device->host)->dma_dir = dir_in;
- DMA(cmd->host)->CNTR = cntr;
+ DMA(cmd->device->host)->CNTR = cntr;
/* setup DMA *physical* address */
- DMA(cmd->host)->ACR = addr;
+ DMA(cmd->device->host)->ACR = addr;
if (dir_in){
/* invalidate any cache */
@@ -117,7 +117,7 @@
cache_push (addr, cmd->SCp.this_residual);
}
/* start DMA */
- DMA(cmd->host)->ST_DMA = 1;
+ DMA(cmd->device->host)->ST_DMA = 1;
/* return success */
return 0;
--- linux-2.5.x/drivers/scsi/atari_NCR5380.c Wed Feb 12 12:31:26 2003
+++ linux-m68k-2.5.x/drivers/scsi/atari_NCR5380.c Thu Feb 13 15:42:37 2003
@@ -266,7 +266,7 @@
#define NEXTADDR(cmd) ((Scsi_Cmnd **)&((cmd)->host_scribble))
#define HOSTNO instance->host_no
-#define H_NO(cmd) (cmd)->host->host_no
+#define H_NO(cmd) (cmd)->device->host->host_no
#ifdef SUPPORT_TAGS
@@ -350,17 +350,17 @@
static int is_lun_busy( Scsi_Cmnd *cmd, int should_be_tagged )
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
- if (hostdata->busy[cmd->target] & (1 << cmd->lun))
+ if (hostdata->busy[cmd->device->id] & (1 << cmd->device->lun))
return( 1 );
if (!should_be_tagged ||
!setup_use_tagged_queuing || !cmd->device->tagged_supported)
return( 0 );
- if (TagAlloc[cmd->target][cmd->lun].nr_allocated >=
- TagAlloc[cmd->target][cmd->lun].queue_size ) {
+ if (TagAlloc[cmd->device->id][cmd->device->lun].nr_allocated >=
+ TagAlloc[cmd->device->id][cmd->device->lun].queue_size ) {
TAG_PRINTK( "scsi%d: target %d lun %d: no free tags\n",
- H_NO(cmd), cmd->target, cmd->lun );
+ H_NO(cmd), cmd->device->id, cmd->device->lun );
return( 1 );
}
return( 0 );
@@ -374,7 +374,7 @@
static void cmd_get_tag( Scsi_Cmnd *cmd, int should_be_tagged )
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
/* If we or the target don't support tagged queuing, allocate the LUN for
* an untagged command.
@@ -382,19 +382,19 @@
if (!should_be_tagged ||
!setup_use_tagged_queuing || !cmd->device->tagged_supported) {
cmd->tag = TAG_NONE;
- hostdata->busy[cmd->target] |= (1 << cmd->lun);
+ hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
TAG_PRINTK( "scsi%d: target %d lun %d now allocated by untagged "
- "command\n", H_NO(cmd), cmd->target, cmd->lun );
+ "command\n", H_NO(cmd), cmd->device->id, cmd->device->lun );
}
else {
- TAG_ALLOC *ta = &TagAlloc[cmd->target][cmd->lun];
+ TAG_ALLOC *ta = &TagAlloc[cmd->device->id][cmd->device->lun];
cmd->tag = find_first_zero_bit( ta->allocated, MAX_TAGS );
set_bit( cmd->tag, ta->allocated );
ta->nr_allocated++;
TAG_PRINTK( "scsi%d: using tag %d for target %d lun %d "
"(now %d tags in use)\n",
- H_NO(cmd), cmd->tag, cmd->target, cmd->lun,
+ H_NO(cmd), cmd->tag, cmd->device->id, cmd->device->lun,
ta->nr_allocated );
}
}
@@ -406,23 +406,23 @@
static void cmd_free_tag( Scsi_Cmnd *cmd )
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
if (cmd->tag == TAG_NONE) {
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
TAG_PRINTK( "scsi%d: target %d lun %d untagged cmd finished\n",
- H_NO(cmd), cmd->target, cmd->lun );
+ H_NO(cmd), cmd->device->id, cmd->device->lun );
}
else if (cmd->tag >= MAX_TAGS) {
printk(KERN_NOTICE "scsi%d: trying to free bad tag %d!\n",
H_NO(cmd), cmd->tag );
}
else {
- TAG_ALLOC *ta = &TagAlloc[cmd->target][cmd->lun];
+ TAG_ALLOC *ta = &TagAlloc[cmd->device->id][cmd->device->lun];
clear_bit( cmd->tag, ta->allocated );
ta->nr_allocated--;
TAG_PRINTK( "scsi%d: freed tag %d for target %d lun %d\n",
- H_NO(cmd), cmd->tag, cmd->target, cmd->lun );
+ H_NO(cmd), cmd->tag, cmd->device->id, cmd->device->lun );
}
}
@@ -811,7 +811,7 @@
int i, s;
unsigned char *command;
SPRINTF("scsi%d: destination target %d, lun %d\n",
- H_NO(cmd), cmd->target, cmd->lun);
+ H_NO(cmd), cmd->device->id, cmd->device->lun);
SPRINTF(" command = ");
command = cmd->cmnd;
SPRINTF("%2d (0x%02x)", command[0], command[0]);
@@ -903,7 +903,7 @@
static
int NCR5380_queue_command (Scsi_Cmnd *cmd, void (*done)(Scsi_Cmnd *))
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
Scsi_Cmnd *tmp;
int oldto;
unsigned long flags;
@@ -937,15 +937,15 @@
case WRITE:
case WRITE_6:
case WRITE_10:
- hostdata->time_write[cmd->target] -= (jiffies - hostdata->timebase);
- hostdata->bytes_write[cmd->target] += cmd->request_bufflen;
+ hostdata->time_write[cmd->device->id] -= (jiffies - hostdata->timebase);
+ hostdata->bytes_write[cmd->device->id] += cmd->request_bufflen;
hostdata->pendingw++;
break;
case READ:
case READ_6:
case READ_10:
- hostdata->time_read[cmd->target] -= (jiffies - hostdata->timebase);
- hostdata->bytes_read[cmd->target] += cmd->request_bufflen;
+ hostdata->time_read[cmd->device->id] -= (jiffies - hostdata->timebase);
+ hostdata->bytes_read[cmd->device->id] += cmd->request_bufflen;
hostdata->pendingr++;
break;
}
@@ -1086,8 +1086,8 @@
#if (NDEBUG & NDEBUG_LISTS)
if (prev != tmp)
printk("MAIN tmp=%p target=%d busy=%d lun=%d\n",
- tmp, tmp->target, hostdata->busy[tmp->target],
- tmp->lun);
+ tmp, tmp->device->id, hostdata->busy[tmp->device->id],
+ tmp->device->lun);
#endif
/* When we find one, remove it from the issue queue. */
/* ++guenther: possible race with Falcon locking */
@@ -1095,7 +1095,7 @@
#ifdef SUPPORT_TAGS
!is_lun_busy( tmp, tmp->cmnd[0] != REQUEST_SENSE)
#else
- !(hostdata->busy[tmp->target] & (1 << tmp->lun))
+ !(hostdata->busy[tmp->device->id] & (1 << tmp->device->lun))
#endif
) {
/* ++guenther: just to be sure, this must be atomic */
@@ -1121,7 +1121,7 @@
*/
MAIN_PRINTK("scsi%d: main(): command for target %d "
"lun %d removed from issue_queue\n",
- HOSTNO, tmp->target, tmp->lun);
+ HOSTNO, tmp->device->id, tmp->device->lun);
/*
* REQUEST SENSE commands are issued without tagged
* queueing, even on SCSI-II devices because the
@@ -1355,15 +1355,15 @@
case WRITE:
case WRITE_6:
case WRITE_10:
- hostdata->time_write[cmd->target] += (jiffies - hostdata->timebase);
- /*hostdata->bytes_write[cmd->target] += cmd->request_bufflen;*/
+ hostdata->time_write[cmd->device->id] += (jiffies - hostdata->timebase);
+ /*hostdata->bytes_write[cmd->device->id] += cmd->request_bufflen;*/
hostdata->pendingw--;
break;
case READ:
case READ_6:
case READ_10:
- hostdata->time_read[cmd->target] += (jiffies - hostdata->timebase);
- /*hostdata->bytes_read[cmd->target] += cmd->request_bufflen;*/
+ hostdata->time_read[cmd->device->id] += (jiffies - hostdata->timebase);
+ /*hostdata->bytes_read[cmd->device->id] += cmd->request_bufflen;*/
hostdata->pendingr--;
break;
}
@@ -1524,7 +1524,7 @@
* the host and target ID's on the SCSI bus.
*/
- NCR5380_write(OUTPUT_DATA_REG, (hostdata->id_mask | (1 << cmd->target)));
+ NCR5380_write(OUTPUT_DATA_REG, (hostdata->id_mask | (1 << cmd->device->id)));
/*
* Raise ATN while SEL is true before BSY goes false from arbitration,
@@ -1577,7 +1577,7 @@
udelay(1);
- SEL_PRINTK("scsi%d: selecting target %d\n", HOSTNO, cmd->target);
+ SEL_PRINTK("scsi%d: selecting target %d\n", HOSTNO, cmd->device->id);
/*
* The SCSI specification calls for a 250 ms timeout for the actual
@@ -1628,7 +1628,7 @@
if (!(NCR5380_read(STATUS_REG) & SR_BSY)) {
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- if (hostdata->targets_present & (1 << cmd->target)) {
+ if (hostdata->targets_present & (1 << cmd->device->id)) {
printk(KERN_ERR "scsi%d: weirdness\n", HOSTNO);
if (hostdata->restart_select)
printk(KERN_NOTICE "\trestart select\n");
@@ -1650,7 +1650,7 @@
return 0;
}
- hostdata->targets_present |= (1 << cmd->target);
+ hostdata->targets_present |= (1 << cmd->device->id);
/*
* Since we followed the SCSI spec, and raised ATN while SEL
@@ -1671,8 +1671,8 @@
while (!(NCR5380_read(STATUS_REG) & SR_REQ));
SEL_PRINTK("scsi%d: target %d selected, going into MESSAGE OUT phase.\n",
- HOSTNO, cmd->target);
- tmp[0] = IDENTIFY(1, cmd->lun);
+ HOSTNO, cmd->device->id);
+ tmp[0] = IDENTIFY(1, cmd->device->lun);
#ifdef SUPPORT_TAGS
if (cmd->tag != TAG_NONE) {
@@ -1694,7 +1694,7 @@
/* XXX need to handle errors here */
hostdata->connected = cmd;
#ifndef SUPPORT_TAGS
- hostdata->busy[cmd->target] |= (1 << cmd->lun);
+ hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
#endif
initialize_SCp(cmd);
@@ -2084,7 +2084,7 @@
* polled-IO. */
printk(KERN_NOTICE "scsi%d: switching target %d "
"lun %d to slow handshake\n", HOSTNO,
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
cmd->device->borken = 1;
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
ICR_ASSERT_ATN);
@@ -2136,7 +2136,7 @@
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
LNK_PRINTK("scsi%d: target %d lun %d linked command "
- "complete.\n", HOSTNO, cmd->target, cmd->lun);
+ "complete.\n", HOSTNO, cmd->device->id, cmd->device->lun);
/* Enable reselect interrupts */
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
@@ -2149,7 +2149,7 @@
if (!cmd->next_link) {
printk(KERN_NOTICE "scsi%d: target %d lun %d "
"linked command complete, no next_link\n",
- HOSTNO, cmd->target, cmd->lun);
+ HOSTNO, cmd->device->id, cmd->device->lun);
sink = 1;
do_abort (instance);
return;
@@ -2162,7 +2162,7 @@
cmd->result = cmd->SCp.Status | (cmd->SCp.Message << 8);
LNK_PRINTK("scsi%d: target %d lun %d linked request "
"done, calling scsi_done().\n",
- HOSTNO, cmd->target, cmd->lun);
+ HOSTNO, cmd->device->id, cmd->device->lun);
#ifdef NCR5380_STATS
collect_stats(hostdata, cmd);
#endif
@@ -2178,7 +2178,7 @@
falcon_dont_release++;
hostdata->connected = NULL;
QU_PRINTK("scsi%d: command for target %d, lun %d "
- "completed\n", HOSTNO, cmd->target, cmd->lun);
+ "completed\n", HOSTNO, cmd->device->id, cmd->device->lun);
#ifdef SUPPORT_TAGS
cmd_free_tag( cmd );
if (status_byte(cmd->SCp.Status) == QUEUE_FULL) {
@@ -2190,16 +2190,16 @@
*/
/* ++Andreas: the mid level code knows about
QUEUE_FULL now. */
- TAG_ALLOC *ta = &TagAlloc[cmd->target][cmd->lun];
+ TAG_ALLOC *ta = &TagAlloc[cmd->device->id][cmd->device->lun];
TAG_PRINTK("scsi%d: target %d lun %d returned "
"QUEUE_FULL after %d commands\n",
- HOSTNO, cmd->target, cmd->lun,
+ HOSTNO, cmd->device->id, cmd->device->lun,
ta->nr_allocated);
if (ta->queue_size > ta->nr_allocated)
ta->nr_allocated = ta->queue_size;
}
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
/* Enable reselect interrupts */
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
@@ -2295,12 +2295,12 @@
* the command is treated as untagged further on.
*/
cmd->device->tagged_supported = 0;
- hostdata->busy[cmd->target] |= (1 << cmd->lun);
+ hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
cmd->tag = TAG_NONE;
TAG_PRINTK("scsi%d: target %d lun %d rejected "
"QUEUE_TAG message; tagged queuing "
"disabled\n",
- HOSTNO, cmd->target, cmd->lun);
+ HOSTNO, cmd->device->id, cmd->device->lun);
break;
}
break;
@@ -2317,7 +2317,7 @@
QU_PRINTK("scsi%d: command for target %d lun %d was "
"moved from connected to the "
"disconnected_queue\n", HOSTNO,
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
/*
* Restore phase bits to 0 so an interrupted selection,
* arbitration can resume.
@@ -2416,13 +2416,13 @@
} else if (tmp != EXTENDED_MESSAGE)
printk(KERN_DEBUG "scsi%d: rejecting unknown "
"message %02x from target %d, lun %d\n",
- HOSTNO, tmp, cmd->target, cmd->lun);
+ HOSTNO, tmp, cmd->device->id, cmd->device->lun);
else
printk(KERN_DEBUG "scsi%d: rejecting unknown "
"extended message "
"code %02x, length %d from target %d, lun %d\n",
HOSTNO, extended_msg[1], extended_msg[0],
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
msgout = MESSAGE_REJECT;
@@ -2440,7 +2440,7 @@
#ifdef SUPPORT_TAGS
cmd_free_tag( cmd );
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
hostdata->connected = NULL;
cmd->result = DID_ERROR << 16;
@@ -2576,7 +2576,7 @@
for (tmp = (Scsi_Cmnd *) hostdata->disconnected_queue, prev = NULL;
tmp; prev = tmp, tmp = NEXT(tmp) ) {
- if ((target_mask == (1 << tmp->target)) && (lun == tmp->lun)
+ if ((target_mask == (1 << tmp->device->id)) && (lun == tmp->device->lun)
#ifdef SUPPORT_TAGS
&& (tag == tmp->tag)
#endif
@@ -2619,7 +2619,7 @@
hostdata->connected = tmp;
RSL_PRINTK("scsi%d: nexus established, target = %d, lun = %d, tag = %d\n",
- HOSTNO, tmp->target, tmp->lun, tmp->tag);
+ HOSTNO, tmp->device->id, tmp->device->lun, tmp->tag);
falcon_dont_release--;
}
@@ -2644,7 +2644,7 @@
static
int NCR5380_abort (Scsi_Cmnd *cmd)
{
- struct Scsi_Host *instance = cmd->host;
+ struct Scsi_Host *instance = cmd->device->host;
SETUP_HOSTDATA(instance);
Scsi_Cmnd *tmp, **prev;
unsigned long flags;
@@ -2698,7 +2698,7 @@
#ifdef SUPPORT_TAGS
cmd_free_tag( cmd );
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
local_irq_restore(flags);
cmd->scsi_done(cmd);
@@ -2805,7 +2805,7 @@
#ifdef SUPPORT_TAGS
cmd_free_tag( tmp );
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
local_irq_restore(flags);
tmp->scsi_done(tmp);
@@ -2849,7 +2849,7 @@
static int NCR5380_bus_reset( Scsi_Cmnd *cmd)
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
int i;
unsigned long flags;
#if 1
@@ -2860,7 +2860,7 @@
printk(KERN_ERR "scsi%d: !!BINGO!! Falcon has no lock in NCR5380_reset\n",
H_NO(cmd) );
- NCR5380_print_status (cmd->host);
+ NCR5380_print_status (cmd->device->host);
/* get in phase */
NCR5380_write( TARGET_COMMAND_REG,
--- linux-2.5.x/drivers/scsi/atari_scsi.c Wed Feb 12 12:31:26 2003
+++ linux-m68k-2.5.x/drivers/scsi/atari_scsi.c Thu Feb 13 15:37:43 2003
@@ -823,7 +823,7 @@
{
int rv;
struct NCR5380_hostdata *hostdata =
- (struct NCR5380_hostdata *)cmd->host->hostdata;
+ (struct NCR5380_hostdata *)cmd->device->host->hostdata;
/* For doing the reset, SCSI interrupts must be disabled first,
* since the 5380 raises its IRQ line while _RST is active and we
--- linux-2.5.x/drivers/scsi/gvp11.c Wed Nov 20 11:36:29 2002
+++ linux-m68k-2.5.x/drivers/scsi/gvp11.c Thu Feb 13 16:15:30 2003
@@ -62,61 +62,62 @@
static int scsi_alloc_out_of_range = 0;
/* use bounce buffer if the physical address is bad */
- if (addr & HDATA(cmd->host)->dma_xfer_mask ||
+ if (addr & HDATA(cmd->device->host)->dma_xfer_mask ||
(!dir_in && mm_end_of_chunk (addr, cmd->SCp.this_residual)))
{
- HDATA(cmd->host)->dma_bounce_len = (cmd->SCp.this_residual + 511)
+ HDATA(cmd->device->host)->dma_bounce_len = (cmd->SCp.this_residual + 511)
& ~0x1ff;
if( !scsi_alloc_out_of_range ) {
- HDATA(cmd->host)->dma_bounce_buffer =
- kmalloc (HDATA(cmd->host)->dma_bounce_len, GFP_KERNEL);
- HDATA(cmd->host)->dma_buffer_pool = BUF_SCSI_ALLOCED;
+ HDATA(cmd->device->host)->dma_bounce_buffer =
+ kmalloc (HDATA(cmd->device->host)->dma_bounce_len, GFP_KERNEL);
+ HDATA(cmd->device->host)->dma_buffer_pool = BUF_SCSI_ALLOCED;
}
- if ( scsi_alloc_out_of_range || !HDATA(cmd->host)->dma_bounce_buffer) {
- HDATA(cmd->host)->dma_bounce_buffer =
- amiga_chip_alloc(HDATA(cmd->host)->dma_bounce_len,
+ if (scsi_alloc_out_of_range ||
+ !HDATA(cmd->device->host)->dma_bounce_buffer) {
+ HDATA(cmd->device->host)->dma_bounce_buffer =
+ amiga_chip_alloc(HDATA(cmd->device->host)->dma_bounce_len,
"GVP II SCSI Bounce Buffer");
- if(!HDATA(cmd->host)->dma_bounce_buffer)
+ if(!HDATA(cmd->device->host)->dma_bounce_buffer)
{
- HDATA(cmd->host)->dma_bounce_len = 0;
+ HDATA(cmd->device->host)->dma_bounce_len = 0;
return 1;
}
- HDATA(cmd->host)->dma_buffer_pool = BUF_CHIP_ALLOCED;
+ HDATA(cmd->device->host)->dma_buffer_pool = BUF_CHIP_ALLOCED;
}
/* check if the address of the bounce buffer is OK */
- addr = virt_to_bus(HDATA(cmd->host)->dma_bounce_buffer);
+ addr = virt_to_bus(HDATA(cmd->device->host)->dma_bounce_buffer);
- if (addr & HDATA(cmd->host)->dma_xfer_mask) {
+ if (addr & HDATA(cmd->device->host)->dma_xfer_mask) {
/* fall back to Chip RAM if address out of range */
- if( HDATA(cmd->host)->dma_buffer_pool == BUF_SCSI_ALLOCED) {
- kfree (HDATA(cmd->host)->dma_bounce_buffer);
+ if( HDATA(cmd->device->host)->dma_buffer_pool == BUF_SCSI_ALLOCED) {
+ kfree (HDATA(cmd->device->host)->dma_bounce_buffer);
scsi_alloc_out_of_range = 1;
} else {
- amiga_chip_free (HDATA(cmd->host)->dma_bounce_buffer);
+ amiga_chip_free (HDATA(cmd->device->host)->dma_bounce_buffer);
}
- HDATA(cmd->host)->dma_bounce_buffer =
- amiga_chip_alloc(HDATA(cmd->host)->dma_bounce_len,
+ HDATA(cmd->device->host)->dma_bounce_buffer =
+ amiga_chip_alloc(HDATA(cmd->device->host)->dma_bounce_len,
"GVP II SCSI Bounce Buffer");
- if(!HDATA(cmd->host)->dma_bounce_buffer)
+ if(!HDATA(cmd->device->host)->dma_bounce_buffer)
{
- HDATA(cmd->host)->dma_bounce_len = 0;
+ HDATA(cmd->device->host)->dma_bounce_len = 0;
return 1;
}
- addr = virt_to_bus(HDATA(cmd->host)->dma_bounce_buffer);
- HDATA(cmd->host)->dma_buffer_pool = BUF_CHIP_ALLOCED;
+ addr = virt_to_bus(HDATA(cmd->device->host)->dma_bounce_buffer);
+ HDATA(cmd->device->host)->dma_buffer_pool = BUF_CHIP_ALLOCED;
}
if (!dir_in) {
/* copy to bounce buffer for a write */
- memcpy (HDATA(cmd->host)->dma_bounce_buffer,
+ memcpy (HDATA(cmd->device->host)->dma_bounce_buffer,
cmd->SCp.ptr, cmd->SCp.this_residual);
}
}
@@ -125,11 +126,11 @@
if (!dir_in)
cntr |= GVP11_DMAC_DIR_WRITE;
- HDATA(cmd->host)->dma_dir = dir_in;
- DMA(cmd->host)->CNTR = cntr;
+ HDATA(cmd->device->host)->dma_dir = dir_in;
+ DMA(cmd->device->host)->CNTR = cntr;
/* setup DMA *physical* address */
- DMA(cmd->host)->ACR = addr;
+ DMA(cmd->device->host)->ACR = addr;
if (dir_in)
/* invalidate any cache */
@@ -138,11 +139,11 @@
/* push any dirty cache */
cache_push (addr, cmd->SCp.this_residual);
- if ((bank_mask = (~HDATA(cmd->host)->dma_xfer_mask >> 18) & 0x01c0))
- DMA(cmd->host)->BANK = bank_mask & (addr >> 18);
+ if ((bank_mask = (~HDATA(cmd->device->host)->dma_xfer_mask >> 18) & 0x01c0))
+ DMA(cmd->device->host)->BANK = bank_mask & (addr >> 18);
/* start DMA */
- DMA(cmd->host)->ST_DMA = 1;
+ DMA(cmd->device->host)->ST_DMA = 1;
/* return success */
return 0;
--- linux-2.5.x/drivers/scsi/sun3_NCR5380.c Wed Feb 12 17:56:43 2003
+++ linux-m68k-2.5.x/drivers/scsi/sun3_NCR5380.c Thu Feb 13 13:26:45 2003
@@ -268,7 +268,7 @@
#define NEXTADDR(cmd) ((Scsi_Cmnd **)&((cmd)->host_scribble))
#define HOSTNO instance->host_no
-#define H_NO(cmd) (cmd)->host->host_no
+#define H_NO(cmd) (cmd)->device->host->host_no
#define SGADDR(buffer) (void *)(((unsigned long)page_address((buffer)->page)) + \
(buffer)->offset)
@@ -360,17 +360,17 @@
static int is_lun_busy( Scsi_Cmnd *cmd, int should_be_tagged )
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
- if (hostdata->busy[cmd->target] & (1 << cmd->lun))
+ if (hostdata->busy[cmd->device->id] & (1 << cmd->device->lun))
return( 1 );
if (!should_be_tagged ||
!setup_use_tagged_queuing || !cmd->device->tagged_supported)
return( 0 );
- if (TagAlloc[cmd->target][cmd->lun].nr_allocated >=
- TagAlloc[cmd->target][cmd->lun].queue_size ) {
+ if (TagAlloc[cmd->device->id][cmd->device->lun].nr_allocated >=
+ TagAlloc[cmd->device->id][cmd->device->lun].queue_size ) {
TAG_PRINTK( "scsi%d: target %d lun %d: no free tags\n",
- H_NO(cmd), cmd->target, cmd->lun );
+ H_NO(cmd), cmd->device->id, cmd->device->lun );
return( 1 );
}
return( 0 );
@@ -384,7 +384,7 @@
static void cmd_get_tag( Scsi_Cmnd *cmd, int should_be_tagged )
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
/* If we or the target don't support tagged queuing, allocate the LUN for
* an untagged command.
@@ -392,19 +392,19 @@
if (!should_be_tagged ||
!setup_use_tagged_queuing || !cmd->device->tagged_supported) {
cmd->tag = TAG_NONE;
- hostdata->busy[cmd->target] |= (1 << cmd->lun);
+ hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
TAG_PRINTK( "scsi%d: target %d lun %d now allocated by untagged "
- "command\n", H_NO(cmd), cmd->target, cmd->lun );
+ "command\n", H_NO(cmd), cmd->device->id, cmd->device->lun );
}
else {
- TAG_ALLOC *ta = &TagAlloc[cmd->target][cmd->lun];
+ TAG_ALLOC *ta = &TagAlloc[cmd->device->id][cmd->device->lun];
cmd->tag = find_first_zero_bit( &ta->allocated, MAX_TAGS );
set_bit( cmd->tag, &ta->allocated );
ta->nr_allocated++;
TAG_PRINTK( "scsi%d: using tag %d for target %d lun %d "
"(now %d tags in use)\n",
- H_NO(cmd), cmd->tag, cmd->target, cmd->lun,
+ H_NO(cmd), cmd->tag, cmd->device->id, cmd->device->lun,
ta->nr_allocated );
}
}
@@ -416,23 +416,23 @@
static void cmd_free_tag( Scsi_Cmnd *cmd )
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
if (cmd->tag == TAG_NONE) {
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
TAG_PRINTK( "scsi%d: target %d lun %d untagged cmd finished\n",
- H_NO(cmd), cmd->target, cmd->lun );
+ H_NO(cmd), cmd->device->id, cmd->device->lun );
}
else if (cmd->tag >= MAX_TAGS) {
printk(KERN_NOTICE "scsi%d: trying to free bad tag %d!\n",
H_NO(cmd), cmd->tag );
}
else {
- TAG_ALLOC *ta = &TagAlloc[cmd->target][cmd->lun];
+ TAG_ALLOC *ta = &TagAlloc[cmd->device->id][cmd->device->lun];
clear_bit( cmd->tag, &ta->allocated );
ta->nr_allocated--;
TAG_PRINTK( "scsi%d: freed tag %d for target %d lun %d\n",
- H_NO(cmd), cmd->tag, cmd->target, cmd->lun );
+ H_NO(cmd), cmd->tag, cmd->device->id, cmd->device->lun );
}
}
@@ -819,7 +819,7 @@
int i, s;
unsigned char *command;
SPRINTF("scsi%d: destination target %d, lun %d\n",
- H_NO(cmd), cmd->target, cmd->lun);
+ H_NO(cmd), cmd->device->id, cmd->device->lun);
SPRINTF(" command = ");
command = cmd->cmnd;
SPRINTF("%2d (0x%02x)", command[0], command[0]);
@@ -911,7 +911,7 @@
/* Only make static if a wrapper function is used */
static int NCR5380_queue_command (Scsi_Cmnd *cmd, void (*done)(Scsi_Cmnd *))
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
Scsi_Cmnd *tmp;
unsigned long flags;
@@ -943,15 +943,15 @@
case WRITE:
case WRITE_6:
case WRITE_10:
- hostdata->time_write[cmd->target] -= (jiffies - hostdata->timebase);
- hostdata->bytes_write[cmd->target] += cmd->request_bufflen;
+ hostdata->time_write[cmd->device->id] -= (jiffies - hostdata->timebase);
+ hostdata->bytes_write[cmd->device->id] += cmd->request_bufflen;
hostdata->pendingw++;
break;
case READ:
case READ_6:
case READ_10:
- hostdata->time_read[cmd->target] -= (jiffies - hostdata->timebase);
- hostdata->bytes_read[cmd->target] += cmd->request_bufflen;
+ hostdata->time_read[cmd->device->id] -= (jiffies - hostdata->timebase);
+ hostdata->bytes_read[cmd->device->id] += cmd->request_bufflen;
hostdata->pendingr++;
break;
}
@@ -1096,7 +1096,7 @@
#ifdef SUPPORT_TAGS
!is_lun_busy( tmp, tmp->cmnd[0] != REQUEST_SENSE)
#else
- !(hostdata->busy[tmp->target] & (1 << tmp->lun))
+ !(hostdata->busy[tmp->device->id] & (1 << tmp->device->lun))
#endif
) {
/* ++guenther: just to be sure, this must be atomic */
@@ -1350,15 +1350,15 @@
case WRITE:
case WRITE_6:
case WRITE_10:
- hostdata->time_write[cmd->target] += (jiffies - hostdata->timebase);
- /*hostdata->bytes_write[cmd->target] += cmd->request_bufflen;*/
+ hostdata->time_write[cmd->device->id] += (jiffies - hostdata->timebase);
+ /*hostdata->bytes_write[cmd->device->id] += cmd->request_bufflen;*/
hostdata->pendingw--;
break;
case READ:
case READ_6:
case READ_10:
- hostdata->time_read[cmd->target] += (jiffies - hostdata->timebase);
- /*hostdata->bytes_read[cmd->target] += cmd->request_bufflen;*/
+ hostdata->time_read[cmd->device->id] += (jiffies - hostdata->timebase);
+ /*hostdata->bytes_read[cmd->device->id] += cmd->request_bufflen;*/
hostdata->pendingr--;
break;
}
@@ -1519,7 +1519,7 @@
* the host and target ID's on the SCSI bus.
*/
- NCR5380_write(OUTPUT_DATA_REG, (hostdata->id_mask | (1 << cmd->target)));
+ NCR5380_write(OUTPUT_DATA_REG, (hostdata->id_mask | (1 << cmd->device->id)));
/*
* Raise ATN while SEL is true before BSY goes false from arbitration,
@@ -1572,7 +1572,7 @@
udelay(1);
- SEL_PRINTK("scsi%d: selecting target %d\n", HOSTNO, cmd->target);
+ SEL_PRINTK("scsi%d: selecting target %d\n", HOSTNO, cmd->device->id);
/*
* The SCSI specification calls for a 250 ms timeout for the actual
@@ -1623,7 +1623,7 @@
if (!(NCR5380_read(STATUS_REG) & SR_BSY)) {
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- if (hostdata->targets_present & (1 << cmd->target)) {
+ if (hostdata->targets_present & (1 << cmd->device->id)) {
printk(KERN_ERR "scsi%d: weirdness\n", HOSTNO);
if (hostdata->restart_select)
printk(KERN_NOTICE "\trestart select\n");
@@ -1645,7 +1645,7 @@
return 0;
}
- hostdata->targets_present |= (1 << cmd->target);
+ hostdata->targets_present |= (1 << cmd->device->id);
/*
* Since we followed the SCSI spec, and raised ATN while SEL
@@ -1666,8 +1666,8 @@
while (!(NCR5380_read(STATUS_REG) & SR_REQ));
SEL_PRINTK("scsi%d: target %d selected, going into MESSAGE OUT phase.\n",
- HOSTNO, cmd->target);
- tmp[0] = IDENTIFY(1, cmd->lun);
+ HOSTNO, cmd->device->id);
+ tmp[0] = IDENTIFY(1, cmd->device->lun);
#ifdef SUPPORT_TAGS
if (cmd->tag != TAG_NONE) {
@@ -1689,7 +1689,7 @@
/* XXX need to handle errors here */
hostdata->connected = cmd;
#ifndef SUPPORT_TAGS
- hostdata->busy[cmd->target] |= (1 << cmd->lun);
+ hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
#endif
#ifdef SUN3_SCSI_VME
dregs->csr |= CSR_INTR;
@@ -2104,7 +2104,7 @@
* polled-IO. */
printk(KERN_NOTICE "scsi%d: switching target %d "
"lun %d to slow handshake\n", HOSTNO,
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
cmd->device->borken = 1;
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
ICR_ASSERT_ATN);
@@ -2162,7 +2162,7 @@
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
LNK_PRINTK("scsi%d: target %d lun %d linked command "
- "complete.\n", HOSTNO, cmd->target, cmd->lun);
+ "complete.\n", HOSTNO, cmd->device->id, cmd->device->lun);
/* Enable reselect interrupts */
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
@@ -2175,7 +2175,7 @@
if (!cmd->next_link) {
printk(KERN_NOTICE "scsi%d: target %d lun %d "
"linked command complete, no next_link\n",
- HOSTNO, cmd->target, cmd->lun);
+ HOSTNO, cmd->device->id, cmd->device->lun);
sink = 1;
do_abort (instance);
return;
@@ -2188,7 +2188,7 @@
cmd->result = cmd->SCp.Status | (cmd->SCp.Message << 8);
LNK_PRINTK("scsi%d: target %d lun %d linked request "
"done, calling scsi_done().\n",
- HOSTNO, cmd->target, cmd->lun);
+ HOSTNO, cmd->device->id, cmd->device->lun);
#ifdef NCR5380_STATS
collect_stats(hostdata, cmd);
#endif
@@ -2202,7 +2202,7 @@
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
hostdata->connected = NULL;
QU_PRINTK("scsi%d: command for target %d, lun %d "
- "completed\n", HOSTNO, cmd->target, cmd->lun);
+ "completed\n", HOSTNO, cmd->device->id, cmd->device->lun);
#ifdef SUPPORT_TAGS
cmd_free_tag( cmd );
if (status_byte(cmd->SCp.Status) == QUEUE_FULL) {
@@ -2214,16 +2214,16 @@
*/
/* ++Andreas: the mid level code knows about
QUEUE_FULL now. */
- TAG_ALLOC *ta = &TagAlloc[cmd->target][cmd->lun];
+ TAG_ALLOC *ta = &TagAlloc[cmd->device->id][cmd->device->lun];
TAG_PRINTK("scsi%d: target %d lun %d returned "
"QUEUE_FULL after %d commands\n",
- HOSTNO, cmd->target, cmd->lun,
+ HOSTNO, cmd->device->id, cmd->device->lun,
ta->nr_allocated);
if (ta->queue_size > ta->nr_allocated)
ta->nr_allocated = ta->queue_size;
}
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
/* Enable reselect interrupts */
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
@@ -2313,12 +2313,12 @@
* the command is treated as untagged further on.
*/
cmd->device->tagged_supported = 0;
- hostdata->busy[cmd->target] |= (1 << cmd->lun);
+ hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
cmd->tag = TAG_NONE;
TAG_PRINTK("scsi%d: target %d lun %d rejected "
"QUEUE_TAG message; tagged queuing "
"disabled\n",
- HOSTNO, cmd->target, cmd->lun);
+ HOSTNO, cmd->device->id, cmd->device->lun);
break;
}
break;
@@ -2335,7 +2335,7 @@
QU_PRINTK("scsi%d: command for target %d lun %d was "
"moved from connected to the "
"disconnected_queue\n", HOSTNO,
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
/*
* Restore phase bits to 0 so an interrupted selection,
* arbitration can resume.
@@ -2437,13 +2437,13 @@
} else if (tmp != EXTENDED_MESSAGE)
printk(KERN_DEBUG "scsi%d: rejecting unknown "
"message %02x from target %d, lun %d\n",
- HOSTNO, tmp, cmd->target, cmd->lun);
+ HOSTNO, tmp, cmd->device->id, cmd->device->lun);
else
printk(KERN_DEBUG "scsi%d: rejecting unknown "
"extended message "
"code %02x, length %d from target %d, lun %d\n",
HOSTNO, extended_msg[1], extended_msg[0],
- cmd->target, cmd->lun);
+ cmd->device->id, cmd->device->lun);
msgout = MESSAGE_REJECT;
@@ -2461,7 +2461,7 @@
#ifdef SUPPORT_TAGS
cmd_free_tag( cmd );
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
hostdata->connected = NULL;
cmd->result = DID_ERROR << 16;
@@ -2580,7 +2580,7 @@
for (tmp = (Scsi_Cmnd *) hostdata->disconnected_queue, prev = NULL;
tmp; prev = tmp, tmp = NEXT(tmp) ) {
- if ((target_mask == (1 << tmp->target)) && (lun == tmp->lun)
+ if ((target_mask == (1 << tmp->device->id)) && (lun == tmp->device->lun)
#ifdef SUPPORT_TAGS
&& (tag == tmp->tag)
#endif
@@ -2687,7 +2687,7 @@
static int NCR5380_abort (Scsi_Cmnd *cmd)
{
- struct Scsi_Host *instance = cmd->host;
+ struct Scsi_Host *instance = cmd->device->host;
SETUP_HOSTDATA(instance);
Scsi_Cmnd *tmp, **prev;
unsigned long flags;
@@ -2737,7 +2737,7 @@
#ifdef SUPPORT_TAGS
cmd_free_tag( cmd );
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
local_irq_restore(flags);
cmd->scsi_done(cmd);
@@ -2842,7 +2842,7 @@
#ifdef SUPPORT_TAGS
cmd_free_tag( tmp );
#else
- hostdata->busy[cmd->target] &= ~(1 << cmd->lun);
+ hostdata->busy[cmd->device->id] &= ~(1 << cmd->device->lun);
#endif
local_irq_restore(flags);
tmp->scsi_done(tmp);
@@ -2879,7 +2879,7 @@
static int NCR5380_bus_reset( Scsi_Cmnd *cmd)
{
- SETUP_HOSTDATA(cmd->host);
+ SETUP_HOSTDATA(cmd->device->host);
int i;
unsigned long flags;
#if 1
@@ -2887,7 +2887,7 @@
#endif
- NCR5380_print_status (cmd->host);
+ NCR5380_print_status (cmd->device->host);
/* get in phase */
NCR5380_write( TARGET_COMMAND_REG,
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
reply other threads:[~2003-03-19 12:20 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200303191227.h2JCRg200889@vervain.sonytel.be \
--to=geert@linux-m68k.org \
--cc=linux-kernel@vger.kernel.org \
--cc=torvalds@transmeta.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).