From: Grygorii Strashko <grygorii.strashko@ti.com>
To: Wolfram Sang <wsa@the-dreams.de>, Tony Lindgren <tony@atomide.com>
Cc: <linux-kernel@vger.kernel.org>, <linux-omap@vger.kernel.org>,
<linux-i2c@vger.kernel.org>,
Kevin Hilman <khilman@deeprootsystems.com>,
Nishanth Menon <nm@ti.com>, Kevin Hilman <khilman@linaro.org>,
Grygorii Strashko <grygorii.strashko@ti.com>
Subject: [PATCH 1/5] i2c: omap: fix spurious IRQs: disable/enable IRQ at INTC when idle
Date: Fri, 7 Jun 2013 21:46:04 +0300 [thread overview]
Message-ID: <1370630768-4077-2-git-send-email-grygorii.strashko@ti.com> (raw)
In-Reply-To: <1370630768-4077-1-git-send-email-grygorii.strashko@ti.com>
From: Kevin Hilman <khilman@deeprootsystems.com>
Currently, runtime PM is used to keep the device enabled only during
active transfers and for a configurable runtime PM autosuspend timout
after an xfer.
In addition to idling the device, driver's ->runtime_suspend() method
currently disables device interrupts when idle. However, on some SoCs
(notably OMAP4+), the I2C hardware may shared with other coprocessors.
This means that the MPU will still recieve interrupts if a coprocessor
is using the I2C device. To avoid this, also disable interrupts at
the MPU INTC when idling the device in ->runtime_suspend() (and
re-enable them in ->runtime_resume().) This part based on an original
patch from Shubhrajyoti Datta. NOTE: for proper sharing the I2C with
a coprocessor, this driver still needs hwspinlock support added.
More over, this patch fixes the kernel boot failure which happens when
CONFIG_SENSORS_LM75=y:
[ 2.251220] WARNING: at drivers/bus/omap_l3_noc.c:113 l3_interrupt_handler+0x140/0x184()
[ 2.257781] L3 custom error: MASTER:MPU TARGET:L4 PER2
[ 2.264373] Modules linked in:
[ 2.268463] CPU: 0 PID: 2 Comm: kthreadd Not tainted 3.10.0-rc4-00034-g042dd60-dirty #64
[ 2.270385] [<c001a80c>] (unwind_backtrace+0x0/0xf0) from [<c0017238>] (show_stack+0x10/0x14)
[ 2.286102] [<c0017238>] (show_stack+0x10/0x14) from [<c0040fd0>] (warn_slowpath_common+0x4c/0x68)
[ 2.295593] [<c0040fd0>] (warn_slowpath_common+0x4c/0x68) from [<c0041080>] (warn_slowpath_fmt+0x30/0x40)
[ 2.299987] [<c0041080>] (warn_slowpath_fmt+0x30/0x40) from [<c02c5ed0>] (l3_interrupt_handler+0x140/0x184)
[ 2.315582] [<c02c5ed0>] (l3_interrupt_handler+0x140/0x184) from [<c009ffb8>] (handle_irq_event_percpu+0x58/0x258)
[ 2.323364] [<c009ffb8>] (handle_irq_event_percpu+0x58/0x258) from [<c00a01f4>] (handle_irq_event+0x3c/0x5c)
[ 2.327819] [<c00a01f4>] (handle_irq_event+0x3c/0x5c) from [<c00a2f7c>] (handle_fasteoi_irq+0xbc/0x164)
[ 2.337829] [<c00a2f7c>] (handle_fasteoi_irq+0xbc/0x164) from [<c009f978>] (generic_handle_irq+0x20/0x30)
[ 2.357513] [<c009f978>] (generic_handle_irq+0x20/0x30) from [<c0014168>] (handle_IRQ+0x4c/0xac)
[ 2.366821] [<c0014168>] (handle_IRQ+0x4c/0xac) from [<c00085b4>] (gic_handle_irq+0x28/0x5c)
[ 2.375762] [<c00085b4>] (gic_handle_irq+0x28/0x5c) from [<c04f08a4>] (__irq_svc+0x44/0x5c)
[ 2.379821] Exception stack(0xdb085ec0 to 0xdb085f08)
[ 2.389953] 5ec0: 00000001 00000001 00000000 db07ea00 40000113 db2317a8 db084000 000002f1
[ 2.389953] 5ee0: db07ea00 00000000 00000000 00000000 c04fd990 db085f08 c009170c c04f03e8
[ 2.405609] 5f00: 20000113 ffffffff
[ 2.408355] [<c04f08a4>] (__irq_svc+0x44/0x5c) from [<c04f03e8>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 2.418304] [<c04f03e8>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c00403c0>] (do_fork+0xa4/0x2d4)
[ 2.427795] [<c00403c0>] (do_fork+0xa4/0x2d4) from [<c0040620>] (kernel_thread+0x30/0x38)
[ 2.437805] [<c0040620>] (kernel_thread+0x30/0x38) from [<c0063888>] (kthreadd+0xd4/0x13c)
[ 2.448364] [<c0063888>] (kthreadd+0xd4/0x13c) from [<c0013308>] (ret_from_fork+0x14/0x2c)
[ 2.448364] ---[ end trace da8cf92c433d1616 ]---
The root casue of crash is race between omap_i2c_runtime_suspend()
and omap_i2c_isr_thread()
CPU1: CPU2:
|-omap_i2c_xfer |
|- pm_runtime_put_autosuspend() |
|-timeout |-omap_i2c_isr()
|-return IRQ_WAKE_THREAD;
|-omap_i2c_runtime_suspend() |
|-omap_i2c_isr_thread()
|- oops is here - I2C module is in idle state
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/i2c/busses/i2c-omap.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 64c26f9..97844ff 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -1290,6 +1290,8 @@ static int omap_i2c_runtime_suspend(struct device *dev)
struct platform_device *pdev = to_platform_device(dev);
struct omap_i2c_dev *_dev = platform_get_drvdata(pdev);
+ disable_irq(_dev->irq);
+
_dev->iestate = omap_i2c_read_reg(_dev, OMAP_I2C_IE_REG);
if (_dev->scheme == OMAP_I2C_SCHEME_0)
@@ -1320,6 +1322,8 @@ static int omap_i2c_runtime_resume(struct device *dev)
__omap_i2c_init(_dev);
+ enable_irq(_dev->irq);
+
return 0;
}
#endif /* CONFIG_PM_RUNTIME */
--
1.7.9.5
next prev parent reply other threads:[~2013-06-07 18:50 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-06-07 18:46 [PATCH 0/5] v3.10-rc4: fix OMAP4 boot failure if CONFIG_SENSORS_LM75=y Grygorii Strashko
2013-06-07 18:46 ` Grygorii Strashko [this message]
2013-06-07 20:51 ` [PATCH 1/5] i2c: omap: fix spurious IRQs: disable/enable IRQ at INTC when idle Kevin Hilman
2013-06-19 18:35 ` Grygorii Strashko
2013-06-19 19:31 ` Felipe Balbi
2013-06-19 20:01 ` Kevin Hilman
2013-06-19 20:56 ` Felipe Balbi
2013-06-07 18:46 ` [PATCH 2/5] i2c: omap: add runtime check in isr to be sure that i2c is enabled Grygorii Strashko
2013-06-07 19:02 ` Felipe Balbi
2013-06-19 18:42 ` Grygorii Strashko
2013-06-19 19:39 ` Felipe Balbi
2013-06-07 18:46 ` [PATCH 3/5] i2c: omap: handle all irqs befor unblocking omap_i2c_xfer_msg() Grygorii Strashko
2013-06-07 19:05 ` Felipe Balbi
2013-06-19 18:43 ` Grygorii Strashko
2013-06-19 19:44 ` Felipe Balbi
2013-06-07 18:46 ` [PATCH 4/5] i2c: omap: query STP always when NACK is received Grygorii Strashko
2013-06-07 19:07 ` Felipe Balbi
2013-06-07 18:46 ` [PATCH 5/5] i2c: omap: remove omap_i2c_isr() hw irq handler Grygorii Strashko
2013-06-07 19:07 ` Felipe Balbi
2013-06-19 18:43 ` Grygorii Strashko
2013-06-19 19:44 ` Felipe Balbi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1370630768-4077-2-git-send-email-grygorii.strashko@ti.com \
--to=grygorii.strashko@ti.com \
--cc=khilman@deeprootsystems.com \
--cc=khilman@linaro.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=nm@ti.com \
--cc=tony@atomide.com \
--cc=wsa@the-dreams.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).