From: Chris Zhong <zyw@rock-chips.com>
To: heiko@sntech.de, dianders@chromium.org
Cc: mturquette@linaro.org,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Russell King <linux@arm.linux.org.uk>,
Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Linus Walleij <linus.walleij@linaro.org>,
khilman@kernel.org, linux-rockchip@lists.infradead.org,
Chris Zhong <zyw@rock-chips.com>,
Kumar Gala <galak@codeaurora.org>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v10 4/4] ARM: dts: rockchip: add suspend settings for rk3288-evb-rk808
Date: Mon, 1 Dec 2014 16:52:20 +0800 [thread overview]
Message-ID: <1417423940-1669-5-git-send-email-zyw@rock-chips.com> (raw)
In-Reply-To: <1417423940-1669-1-git-send-email-zyw@rock-chips.com>
Add suspend-voltages and necessary pin-states for suspend on
rk3288-evb-rk808 boards. global_pwroff would be pulled high when
RK3288 entering suspend, this pin is a sleep signal for RK808, so
RK808 could goto sleep mode, and some regulators would be disable.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
---
Changes in v10:
- remove regulator-suspend-mem-enabled and regulator-suspend-mem-microvolt
- enable the lcd, codec, sdmmc power during suspend
Changes in v9:
- update the subject and description
Changes in v8:
- keep all except cpu&tp power rail on during suspend
- add regulator-on-in-suspend before set suspend voltage
- add a reference of ddrio_pwroff and ddr0_retention
Changes in v7:
- add regulator-state-mem sub node for suspend
Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/boot/dts/rk3288-evb-rk808.dts | 53 +++++++++++++++++++++++++++++++++-
1 file changed, 52 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rk3288-evb-rk808.dts
index d8c775e6..d453ddd 100644
--- a/arch/arm/boot/dts/rk3288-evb-rk808.dts
+++ b/arch/arm/boot/dts/rk3288-evb-rk808.dts
@@ -31,7 +31,7 @@
interrupt-parent = <&gpio0>;
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
- pinctrl-0 = <&pmic_int>;
+ pinctrl-0 = <&pmic_int &global_pwroff>;
rockchip,system-power-controller;
wakeup-source;
#clock-cells = <1>;
@@ -50,6 +50,9 @@
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1350000>;
regulator-name = "vdd_arm";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
vdd_gpu: DCDC_REG2 {
@@ -58,12 +61,19 @@
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1250000>;
regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
};
vcc_ddr: DCDC_REG3 {
regulator-always-on;
regulator-boot-on;
regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
vcc_io: DCDC_REG4 {
@@ -72,6 +82,10 @@
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc_io";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
};
vccio_pmu: LDO_REG1 {
@@ -80,6 +94,10 @@
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vccio_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
};
vcc_tp: LDO_REG2 {
@@ -88,6 +106,9 @@
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc_tp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
vdd_10: LDO_REG3 {
@@ -96,6 +117,10 @@
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-name = "vdd_10";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
};
vcc18_lcd: LDO_REG4 {
@@ -104,6 +129,10 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc18_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
};
vccio_sd: LDO_REG5 {
@@ -112,6 +141,10 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
};
vdd10_lcd: LDO_REG6 {
@@ -120,6 +153,10 @@
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-name = "vdd10_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
};
vcc_18: LDO_REG7 {
@@ -128,6 +165,10 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc_18";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
};
vcca_codec: LDO_REG8 {
@@ -136,18 +177,28 @@
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcca_codec";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
};
vcc_wl: SWITCH_REG1 {
regulator-always-on;
regulator-boot-on;
regulator-name = "vcc_wl";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
vcc_lcd: SWITCH_REG2 {
regulator-always-on;
regulator-boot-on;
regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
};
};
--
1.9.1
next prev parent reply other threads:[~2014-12-01 8:53 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-12-01 8:52 [PATCH v10 0/4] This suspend patch is only support cut off the power of cpu and some external Chris Zhong
2014-12-01 8:52 ` [PATCH v10 1/4] ARM: rockchip: add suspend and resume for RK3288 Chris Zhong
2014-12-01 8:52 ` [PATCH v10 2/4] ARM: rockchip: Add pmu-sram binding Chris Zhong
2014-12-01 8:52 ` [PATCH v10 3/4] ARM: dts: add RK3288 suspend support Chris Zhong
2014-12-01 8:52 ` Chris Zhong [this message]
2014-12-01 22:19 ` [PATCH v10 4/4] ARM: dts: rockchip: add suspend settings for rk3288-evb-rk808 Doug Anderson
2014-12-01 19:51 ` [PATCH v10 0/4] This suspend patch is only support cut off the power of cpu and some external Kevin Hilman
2014-12-01 22:08 ` Doug Anderson
2014-12-02 1:07 ` Doug Anderson
2014-12-02 1:26 ` Kevin Hilman
2014-12-03 13:55 ` Chris Zhong
2014-12-03 19:23 ` Kevin Hilman
2014-12-07 23:46 ` Heiko Stübner
2014-12-02 1:18 ` Chris Zhong
2015-01-02 20:57 ` Heiko Stübner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1417423940-1669-5-git-send-email-zyw@rock-chips.com \
--to=zyw@rock-chips.com \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=galak@codeaurora.org \
--cc=heiko@sntech.de \
--cc=ijc+devicetree@hellion.org.uk \
--cc=khilman@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=mturquette@linaro.org \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).