From: Yoshinori Sato <ysato@users.sourceforge.jp>
To: linux-sh@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Subject: [PATCH v4 10/22] sh: Add board specific initialize of of-generic
Date: Wed, 29 Jun 2016 22:40:55 +0900 [thread overview]
Message-ID: <1467207667-15768-11-git-send-email-ysato@users.sourceforge.jp> (raw)
In-Reply-To: <1467207667-15768-1-git-send-email-ysato@users.sourceforge.jp>
Changes v4
none
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
---
arch/sh/boards/of-generic.c | 64 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 64 insertions(+)
diff --git a/arch/sh/boards/of-generic.c b/arch/sh/boards/of-generic.c
index 2d3cda3..709006a 100644
--- a/arch/sh/boards/of-generic.c
+++ b/arch/sh/boards/of-generic.c
@@ -16,9 +16,15 @@
#include <linux/irqchip.h>
#include <linux/clk-provider.h>
#include <linux/memblock.h>
+#include <linux/sm501-regs.h>
#include <asm/machvec.h>
#include <asm/rtc.h>
+struct model_setup {
+ char *name;
+ void (*fn)(void);
+};
+
#ifdef CONFIG_SMP
static void dummy_smp_setup(void)
@@ -125,10 +131,61 @@ static void __init sh_of_time_init(void)
clocksource_probe();
}
+#define PA_LED 0xb0000001 /* LED Control Register */
+#define PA_SHUTDOWN 0xb0000003 /* Shutdown Control Register */
+static void landisk_power_off(void)
+{
+ __raw_writeb(0x01, PA_SHUTDOWN);
+}
+
+static void __init landisk_setup(void)
+{
+ /* LED ON */
+ __raw_writeb(__raw_readb(PA_LED) | 0x03, PA_LED);
+ pm_power_off = landisk_power_off;
+}
+
+#define PA_POWOFF 0xa4000030 /* Board Power OFF control */
+#define PA_OUTPORT 0xa4000036 /* LED control */
+static void rts7751r2d_power_off(void)
+{
+ __raw_writew(0x0001, PA_POWOFF);
+}
+
+static void __init r2dplus_setup(void)
+{
+ void __iomem *sm501_reg;
+
+ __raw_writew(0x0000, PA_OUTPORT);
+ pm_power_off = rts7751r2d_power_off;
+
+ /* sm501 dram configuration:
+ * ColSizeX = 11 - External Memory Column Size: 256 words.
+ * APX = 1 - External Memory Active to Pre-Charge Delay: 7 clocks.
+ * RstX = 1 - External Memory Reset: Normal.
+ * Rfsh = 1 - Local Memory Refresh to Command Delay: 12 clocks.
+ * BwC = 1 - Local Memory Block Write Cycle Time: 2 clocks.
+ * BwP = 1 - Local Memory Block Write to Pre-Charge Delay: 1 clock.
+ * AP = 1 - Internal Memory Active to Pre-Charge Delay: 7 clocks.
+ * Rst = 1 - Internal Memory Reset: Normal.
+ * RA = 1 - Internal Memory Remain in Active State: Do not remain.
+ */
+
+ sm501_reg = (void __iomem *)0xb3e00000 + SM501_DRAM_CONTROL;
+ writel(readl(sm501_reg) | 0x00f107c0, sm501_reg);
+}
+
+static const struct model_setup model_setup_table[] __initconst = {
+ { .name = "I/O DATA HDL-U", .fn = landisk_setup, },
+ { .name = "Renesas RTS7751R2D+", .fn = r2dplus_setup, },
+ {},
+};
+
static void __init sh_of_setup(char **cmdline_p)
{
struct device_node *root;
struct device_node *cpu;
+ const struct model_setup *setup;
u32 freq;
board_time_init = sh_of_time_init;
@@ -145,6 +202,13 @@ static void __init sh_of_setup(char **cmdline_p)
cpu = of_find_node_by_name(NULL, "cpu");
if (!of_property_read_u32(cpu, "clock-frequency", &freq))
preset_lpj = freq / CONFIG_HZ / 2;
+
+ for (setup = model_setup_table; setup->name; setup++) {
+ if (strcmp(setup->name, sh_mv.mv_name) == 0) {
+ setup->fn();
+ break;
+ }
+ }
}
static int sh_of_irq_demux(int irq)
--
2.7.0
next prev parent reply other threads:[~2016-06-29 13:41 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-29 13:40 [PATCH v4 00/22] sh: LANDISK and R2Dplus convert to device tree Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 01/22] sh: Add sh-specific early_init_dt_reserve_memory_arch Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 02/22] sh: More early unflatten device tree Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 03/22] sh: set preset_lpj Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 04/22] sh: Use P1SEGADDR Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 05/22] sh: command line passing chosen/bootargs in devicetree Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 06/22] sh: FDT address save before bank change Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 07/22] sh: Passing FDT address on zImage Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 08/22] sh: Disable board specific code on device tree mode Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 09/22] sh: Use GENERIC_IOMAP " Yoshinori Sato
2016-06-29 13:40 ` Yoshinori Sato [this message]
2016-06-29 13:40 ` [PATCH v4 11/22] sh: SH7750/51 CPG Driver Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 12/22] sh: Add PCI host bridge driver for SH7751 Yoshinori Sato
2016-06-29 14:57 ` Arnd Bergmann
2016-06-30 14:52 ` Yoshinori Sato
2016-07-01 1:43 ` Rob Herring
2016-06-29 13:40 ` [PATCH v4 13/22] sh: irqchip: SH7751 IRQCHIP Driver Yoshinori Sato
2016-06-29 13:40 ` [PATCH v4 14/22] sh: SH7751 core dtsi Yoshinori Sato
2016-07-01 8:57 ` Geert Uytterhoeven
2016-07-03 11:34 ` Yoshinori Sato
2016-07-04 7:15 ` Geert Uytterhoeven
2016-07-04 16:12 ` Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 15/22] sh: Move common PCI stuff to arch/sh/kernel Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 16/22] pci: pci_config_window move to linux/pci.h Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 17/22] pci: PCI_HOST_GENERIC enable for SH Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 18/22] sh: Add separate DTB build rule Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 19/22] sh: IO-DATA HDL-U (a,k.a landisk) IRQCHIP driver Yoshinori Sato
2016-06-29 13:43 ` John Paul Adrian Glaubitz
2016-07-01 1:48 ` Rob Herring
2016-07-03 11:36 ` Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 20/22] sh: IO-DATA HDL-U (a,k.a landisk) DeviceTree Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 21/22] sh: Renesas RTS7751R2Dplus (a,k.a R2Dplus) IRQCHIP Driver Yoshinori Sato
2016-07-01 1:53 ` Rob Herring
2016-07-03 11:35 ` Yoshinori Sato
2016-06-29 13:41 ` [PATCH v4 22/22] sh: Renesas RTS7751R2Dplus (a,k.a R2Dplus) DeviceTree Yoshinori Sato
2016-06-29 14:16 ` Sergei Shtylyov
2016-06-30 14:47 ` Yoshinori Sato
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1467207667-15768-11-git-send-email-ysato@users.sourceforge.jp \
--to=ysato@users.sourceforge.jp \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).