[05/13] misc: panel: Move all suboptions into a big if section
diff mbox series

Message ID 1486391895-9554-6-git-send-email-geert@linux-m68k.org
State New, archived
Headers show
Series
  • Add HD44780 Character LCD support
Related show

Commit Message

Geert Uytterhoeven Feb. 6, 2017, 2:38 p.m. UTC
All 18 suboptions related to the panel driver have individual
dependencies on PANEL.

Replace them by a single "if PANEL / endif # PANEL" section for easier
dependency management.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
 drivers/misc/Kconfig | 37 +++++++++++++++++++------------------
 1 file changed, 19 insertions(+), 18 deletions(-)

Patch
diff mbox series

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 2687ecf3e9e673fa..c290990d73edf87e 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -503,9 +503,10 @@  config PANEL
 	  compiled as a module, or linked into the kernel and started at boot.
 	  If you don't understand what all this is about, say N.
 
+if PANEL
+
 config PANEL_PARPORT
 	int "Default parallel port number (0=LPT1)"
-	depends on PANEL
 	range 0 255
 	default "0"
 	---help---
@@ -517,7 +518,6 @@  config PANEL_PARPORT
 
 config PANEL_PROFILE
 	int "Default panel profile (0-5, 0=custom)"
-	depends on PANEL
 	range 0 5
 	default "5"
 	---help---
@@ -538,7 +538,7 @@  config PANEL_PROFILE
 	  for experts.
 
 config PANEL_KEYPAD
-	depends on PANEL && PANEL_PROFILE="0"
+	depends on PANEL_PROFILE="0"
 	int "Keypad type (0=none, 1=old 6 keys, 2=new 6 keys, 3=Nexcom 4 keys)"
 	range 0 3
 	default 0
@@ -555,7 +555,7 @@  config PANEL_KEYPAD
 	  supports simultaneous keys pressed when the keypad supports them.
 
 config PANEL_LCD
-	depends on PANEL && PANEL_PROFILE="0"
+	depends on PANEL_PROFILE="0"
 	int "LCD type (0=none, 1=custom, 2=old //, 3=ks0074, 4=hantronix, 5=Nexcom)"
 	range 0 5
 	default 0
@@ -578,7 +578,7 @@  config PANEL_LCD
 	   that those values changed from the 2.4 driver for better consistency.
 
 config PANEL_LCD_HEIGHT
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
 	int "Number of lines on the LCD (1-2)"
 	range 1 2
 	default 2
@@ -587,7 +587,7 @@  config PANEL_LCD_HEIGHT
 	  It can either be 1 or 2.
 
 config PANEL_LCD_WIDTH
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
 	int "Number of characters per line on the LCD (1-40)"
 	range 1 40
 	default 40
@@ -596,7 +596,7 @@  config PANEL_LCD_WIDTH
 	  Common values are 16,20,24,40.
 
 config PANEL_LCD_BWIDTH
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
 	int "Internal LCD line width (1-40, 40 by default)"
 	range 1 40
 	default 40
@@ -612,7 +612,7 @@  config PANEL_LCD_BWIDTH
 	  If you don't know, put '40' here.
 
 config PANEL_LCD_HWIDTH
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
 	int "Hardware LCD line width (1-64, 64 by default)"
 	range 1 64
 	default 64
@@ -626,7 +626,7 @@  config PANEL_LCD_HWIDTH
 	  64 here for a 2x40.
 
 config PANEL_LCD_CHARSET
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
 	int "LCD character set (0=normal, 1=KS0074)"
 	range 0 1
 	default 0
@@ -642,7 +642,7 @@  config PANEL_LCD_CHARSET
 	  If you don't know, use the normal one (0).
 
 config PANEL_LCD_PROTO
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
 	int "LCD communication mode (0=parallel 8 bits, 1=serial)"
 	range 0 1
 	default 0
@@ -655,7 +655,7 @@  config PANEL_LCD_PROTO
 	  parallel LCD, and 1 for a serial LCD.
 
 config PANEL_LCD_PIN_E
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
         int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) "
 	range -17 17
 	default 14
@@ -670,7 +670,7 @@  config PANEL_LCD_PIN_E
 	  Default for the 'E' pin in custom profile is '14' (AUTOFEED).
 
 config PANEL_LCD_PIN_RS
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
         int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) "
 	range -17 17
 	default 17
@@ -685,7 +685,7 @@  config PANEL_LCD_PIN_RS
 	  Default for the 'RS' pin in custom profile is '17' (SELECT IN).
 
 config PANEL_LCD_PIN_RW
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
         int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) "
 	range -17 17
 	default 16
@@ -700,7 +700,7 @@  config PANEL_LCD_PIN_RW
 	  Default for the 'RW' pin in custom profile is '16' (INIT).
 
 config PANEL_LCD_PIN_SCL
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
         int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) "
 	range -17 17
 	default 1
@@ -715,7 +715,7 @@  config PANEL_LCD_PIN_SCL
 	  Default for the 'SCL' pin in custom profile is '1' (STROBE).
 
 config PANEL_LCD_PIN_SDA
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
         int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) "
 	range -17 17
 	default 2
@@ -730,7 +730,7 @@  config PANEL_LCD_PIN_SDA
 	  Default for the 'SDA' pin in custom profile is '2' (D0).
 
 config PANEL_LCD_PIN_BL
-	depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
+	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
         int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) "
 	range -17 17
 	default 0
@@ -745,7 +745,6 @@  config PANEL_LCD_PIN_BL
 	  Default for the 'BL' pin in custom profile is '0' (uncontrolled).
 
 config PANEL_CHANGE_MESSAGE
-	depends on PANEL
 	bool "Change LCD initialization message ?"
 	default "n"
 	---help---
@@ -758,7 +757,7 @@  config PANEL_CHANGE_MESSAGE
 	  say 'N' and keep the default message with the version.
 
 config PANEL_BOOT_MESSAGE
-	depends on PANEL && PANEL_CHANGE_MESSAGE="y"
+	depends on PANEL_CHANGE_MESSAGE="y"
 	string "New initialization message"
 	default ""
 	---help---
@@ -770,6 +769,8 @@  config PANEL_BOOT_MESSAGE
 	  An empty message will only clear the display at driver init time. Any other
 	  printf()-formatted message is valid with newline and escape codes.
 
+endif # PANEL
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"