From: Guenter Roeck <linux@roeck-us.net>
To: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org, linux-kernel@vger.kernel.org,
"Zoltán Böszörményi" <zboszor@pr.hu>,
"Guenter Roeck" <linux@roeck-us.net>
Subject: [PATCH 01/12] watchdog: sp5100_tco: Always use SP5100_IO_PM_{INDEX_REG,DATA_REG}
Date: Sun, 24 Dec 2017 13:04:06 -0800 [thread overview]
Message-ID: <1514149457-20273-2-git-send-email-linux@roeck-us.net> (raw)
In-Reply-To: <1514149457-20273-1-git-send-email-linux@roeck-us.net>
SP5100_IO_PM_INDEX_REG and SB800_IO_PM_INDEX_REG are used inconsistently
and define the same value. Just use SP5100_IO_PM_INDEX_REG throughout.
Do the same for SP5100_IO_PM_DATA_REG and SB800_IO_PM_DATA_REG.
Use helper functions to access the indexed registers.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
---
drivers/watchdog/sp5100_tco.c | 94 ++++++++++++++++++++++---------------------
drivers/watchdog/sp5100_tco.h | 7 +---
2 files changed, 51 insertions(+), 50 deletions(-)
diff --git a/drivers/watchdog/sp5100_tco.c b/drivers/watchdog/sp5100_tco.c
index 028618c5eeba..05f9d27a306a 100644
--- a/drivers/watchdog/sp5100_tco.c
+++ b/drivers/watchdog/sp5100_tco.c
@@ -48,7 +48,6 @@
static u32 tcobase_phys;
static u32 tco_wdt_fired;
static void __iomem *tcobase;
-static unsigned int pm_iobase;
static DEFINE_SPINLOCK(tco_lock); /* Guards the hardware */
static unsigned long timer_alive;
static char tco_expect_close;
@@ -132,25 +131,38 @@ static int tco_timer_set_heartbeat(int t)
return 0;
}
-static void tco_timer_enable(void)
+static u8 sp5100_tco_read_pm_reg8(u8 index)
+{
+ outb(index, SP5100_IO_PM_INDEX_REG);
+ return inb(SP5100_IO_PM_DATA_REG);
+}
+
+static void sp5100_tco_update_pm_reg8(u8 index, u8 reset, u8 set)
{
- int val;
+ u8 val;
+ outb(index, SP5100_IO_PM_INDEX_REG);
+ val = inb(SP5100_IO_PM_DATA_REG);
+ val &= reset;
+ val |= set;
+ outb(val, SP5100_IO_PM_DATA_REG);
+}
+
+static void tco_timer_enable(void)
+{
if (!tco_has_sp5100_reg_layout(sp5100_tco_pci)) {
/* For SB800 or later */
/* Set the Watchdog timer resolution to 1 sec */
- outb(SB800_PM_WATCHDOG_CONFIG, SB800_IO_PM_INDEX_REG);
- val = inb(SB800_IO_PM_DATA_REG);
- val |= SB800_PM_WATCHDOG_SECOND_RES;
- outb(val, SB800_IO_PM_DATA_REG);
+ sp5100_tco_update_pm_reg8(SB800_PM_WATCHDOG_CONFIG,
+ 0xff, SB800_PM_WATCHDOG_SECOND_RES);
/* Enable watchdog decode bit and watchdog timer */
- outb(SB800_PM_WATCHDOG_CONTROL, SB800_IO_PM_INDEX_REG);
- val = inb(SB800_IO_PM_DATA_REG);
- val |= SB800_PCI_WATCHDOG_DECODE_EN;
- val &= ~SB800_PM_WATCHDOG_DISABLE;
- outb(val, SB800_IO_PM_DATA_REG);
+ sp5100_tco_update_pm_reg8(SB800_PM_WATCHDOG_CONTROL,
+ ~SB800_PM_WATCHDOG_DISABLE,
+ SB800_PCI_WATCHDOG_DECODE_EN);
} else {
+ u32 val;
+
/* For SP5100 or SB7x0 */
/* Enable watchdog decode bit */
pci_read_config_dword(sp5100_tco_pci,
@@ -164,11 +176,9 @@ static void tco_timer_enable(void)
val);
/* Enable Watchdog timer and set the resolution to 1 sec */
- outb(SP5100_PM_WATCHDOG_CONTROL, SP5100_IO_PM_INDEX_REG);
- val = inb(SP5100_IO_PM_DATA_REG);
- val |= SP5100_PM_WATCHDOG_SECOND_RES;
- val &= ~SP5100_PM_WATCHDOG_DISABLE;
- outb(val, SP5100_IO_PM_DATA_REG);
+ sp5100_tco_update_pm_reg8(SP5100_PM_WATCHDOG_CONTROL,
+ ~SP5100_PM_WATCHDOG_DISABLE,
+ SP5100_PM_WATCHDOG_SECOND_RES);
}
}
@@ -321,6 +331,17 @@ static const struct pci_device_id sp5100_tco_pci_tbl[] = {
};
MODULE_DEVICE_TABLE(pci, sp5100_tco_pci_tbl);
+static u8 sp5100_tco_read_pm_reg32(u8 index)
+{
+ u32 val = 0;
+ int i;
+
+ for (i = 3; i >= 0; i--)
+ val = (val << 8) + sp5100_tco_read_pm_reg8(index + i);
+
+ return val;
+}
+
/*
* Init & exit routines
*/
@@ -329,7 +350,7 @@ static unsigned char sp5100_tco_setupdevice(void)
struct pci_dev *dev = NULL;
const char *dev_name = NULL;
u32 val;
- u32 index_reg, data_reg, base_addr;
+ u8 base_addr;
/* Match the PCI device */
for_each_pci_dev(dev) {
@@ -351,35 +372,25 @@ static unsigned char sp5100_tco_setupdevice(void)
*/
if (tco_has_sp5100_reg_layout(sp5100_tco_pci)) {
dev_name = SP5100_DEVNAME;
- index_reg = SP5100_IO_PM_INDEX_REG;
- data_reg = SP5100_IO_PM_DATA_REG;
base_addr = SP5100_PM_WATCHDOG_BASE;
} else {
dev_name = SB800_DEVNAME;
- index_reg = SB800_IO_PM_INDEX_REG;
- data_reg = SB800_IO_PM_DATA_REG;
base_addr = SB800_PM_WATCHDOG_BASE;
}
/* Request the IO ports used by this driver */
- pm_iobase = SP5100_IO_PM_INDEX_REG;
- if (!request_region(pm_iobase, SP5100_PM_IOPORTS_SIZE, dev_name)) {
- pr_err("I/O address 0x%04x already in use\n", pm_iobase);
+ if (!request_region(SP5100_IO_PM_INDEX_REG, SP5100_PM_IOPORTS_SIZE,
+ dev_name)) {
+ pr_err("I/O address 0x%04x already in use\n",
+ SP5100_IO_PM_INDEX_REG);
goto exit;
}
/*
* First, Find the watchdog timer MMIO address from indirect I/O.
+ * Low three bits of BASE are reserved.
*/
- outb(base_addr+3, index_reg);
- val = inb(data_reg);
- outb(base_addr+2, index_reg);
- val = val << 8 | inb(data_reg);
- outb(base_addr+1, index_reg);
- val = val << 8 | inb(data_reg);
- outb(base_addr+0, index_reg);
- /* Low three bits of BASE are reserved */
- val = val << 8 | (inb(data_reg) & 0xf8);
+ val = sp5100_tco_read_pm_reg32(base_addr) & 0xfffffff8;
pr_debug("Got 0x%04x from indirect I/O\n", val);
@@ -400,14 +411,7 @@ static unsigned char sp5100_tco_setupdevice(void)
SP5100_SB_RESOURCE_MMIO_BASE, &val);
} else {
/* Read SBResource_MMIO from AcpiMmioEn(PM_Reg: 24h) */
- outb(SB800_PM_ACPI_MMIO_EN+3, SB800_IO_PM_INDEX_REG);
- val = inb(SB800_IO_PM_DATA_REG);
- outb(SB800_PM_ACPI_MMIO_EN+2, SB800_IO_PM_INDEX_REG);
- val = val << 8 | inb(SB800_IO_PM_DATA_REG);
- outb(SB800_PM_ACPI_MMIO_EN+1, SB800_IO_PM_INDEX_REG);
- val = val << 8 | inb(SB800_IO_PM_DATA_REG);
- outb(SB800_PM_ACPI_MMIO_EN+0, SB800_IO_PM_INDEX_REG);
- val = val << 8 | inb(SB800_IO_PM_DATA_REG);
+ val = sp5100_tco_read_pm_reg32(SB800_PM_ACPI_MMIO_EN);
}
/* The SBResource_MMIO is enabled and mapped memory space? */
@@ -470,7 +474,7 @@ static unsigned char sp5100_tco_setupdevice(void)
unreg_mem_region:
release_mem_region(tcobase_phys, SP5100_WDT_MEM_MAP_SIZE);
unreg_region:
- release_region(pm_iobase, SP5100_PM_IOPORTS_SIZE);
+ release_region(SP5100_IO_PM_INDEX_REG, SP5100_PM_IOPORTS_SIZE);
exit:
return 0;
}
@@ -517,7 +521,7 @@ static int sp5100_tco_init(struct platform_device *dev)
exit:
iounmap(tcobase);
release_mem_region(tcobase_phys, SP5100_WDT_MEM_MAP_SIZE);
- release_region(pm_iobase, SP5100_PM_IOPORTS_SIZE);
+ release_region(SP5100_IO_PM_INDEX_REG, SP5100_PM_IOPORTS_SIZE);
return ret;
}
@@ -531,7 +535,7 @@ static void sp5100_tco_cleanup(void)
misc_deregister(&sp5100_tco_miscdev);
iounmap(tcobase);
release_mem_region(tcobase_phys, SP5100_WDT_MEM_MAP_SIZE);
- release_region(pm_iobase, SP5100_PM_IOPORTS_SIZE);
+ release_region(SP5100_IO_PM_INDEX_REG, SP5100_PM_IOPORTS_SIZE);
}
static int sp5100_tco_remove(struct platform_device *dev)
diff --git a/drivers/watchdog/sp5100_tco.h b/drivers/watchdog/sp5100_tco.h
index 1af4dee71337..f495fe03887a 100644
--- a/drivers/watchdog/sp5100_tco.h
+++ b/drivers/watchdog/sp5100_tco.h
@@ -24,10 +24,11 @@
* read them from a register.
*/
-/* For SP5100/SB7x0 chipset */
+/* For SP5100/SB7x0/SB8x0 chipset */
#define SP5100_IO_PM_INDEX_REG 0xCD6
#define SP5100_IO_PM_DATA_REG 0xCD7
+/* For SP5100/SB7x0 chipset */
#define SP5100_SB_RESOURCE_MMIO_BASE 0x9C
#define SP5100_PM_WATCHDOG_CONTROL 0x69
@@ -44,11 +45,7 @@
#define SP5100_DEVNAME "SP5100 TCO"
-
/* For SB8x0(or later) chipset */
-#define SB800_IO_PM_INDEX_REG 0xCD6
-#define SB800_IO_PM_DATA_REG 0xCD7
-
#define SB800_PM_ACPI_MMIO_EN 0x24
#define SB800_PM_WATCHDOG_CONTROL 0x48
#define SB800_PM_WATCHDOG_BASE 0x48
--
2.7.4
next prev parent reply other threads:[~2017-12-24 21:04 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-24 21:04 [PATCH 00/12] watchdog: sp5100_tco: Various improvements Guenter Roeck
2017-12-24 21:04 ` Guenter Roeck [this message]
2017-12-24 21:04 ` [PATCH 02/12] watchdog: sp5100_tco: Fix watchdog disable bit Guenter Roeck
2017-12-24 21:04 ` [PATCH 03/12] watchdog: sp5100_tco: Use request_muxed_region where possible Guenter Roeck
2018-01-16 19:44 ` [03/12] " Lyude Paul
2018-01-16 20:16 ` Guenter Roeck
2017-12-24 21:04 ` [PATCH 04/12] watchdog: sp5100_tco: Use standard error codes Guenter Roeck
2018-01-16 19:46 ` [04/12] " Lyude Paul
2017-12-24 21:04 ` [PATCH 05/12] watchdog: sp5100_tco: Clean up sp5100_tco_setupdevice Guenter Roeck
2018-01-16 19:55 ` [05/12] " Lyude Paul
2018-01-16 20:22 ` Guenter Roeck
2018-01-17 1:28 ` Guenter Roeck
2017-12-24 21:04 ` [PATCH 06/12] watchdog: sp5100_tco: Match PCI device early Guenter Roeck
2018-01-16 19:58 ` [06/12] " Lyude Paul
2017-12-24 21:04 ` [PATCH 07/12] watchdog: sp5100_tco: Use dev_ print functions where possible Guenter Roeck
2018-01-16 20:00 ` [07/12] " Lyude Paul
2017-12-24 21:04 ` [PATCH 08/12] watchdog: sp5100_tco: Clean up function and variable names Guenter Roeck
2018-01-16 20:05 ` [08/12] " Lyude Paul
2017-12-24 21:04 ` [PATCH 09/12] watchdog: sp5100_tco: Convert to use watchdog subsystem Guenter Roeck
2017-12-24 21:04 ` [PATCH 10/12] watchdog: sp5100_tco: Use bit operations Guenter Roeck
2017-12-24 21:04 ` [PATCH 11/12] watchdog: sp5100-tco: Abort if watchdog is disabled by hardware Guenter Roeck
2018-01-09 22:58 ` [11/12] " Lyude Paul
2018-01-09 23:37 ` Guenter Roeck
2018-01-09 23:58 ` Gabriel C
2018-01-10 0:05 ` Guenter Roeck
2018-01-10 1:26 ` Gabriel C
2018-01-10 2:09 ` Guenter Roeck
2018-01-10 2:41 ` Gabriel C
2018-01-10 5:02 ` Guenter Roeck
2018-01-10 0:04 ` Lyude Paul
2018-01-10 0:11 ` Guenter Roeck
2018-01-10 0:30 ` Lyude Paul
2017-12-24 21:04 ` [PATCH 12/12] watchdog: sp5100_tco: Add support for recent FCH versions Guenter Roeck
[not found] ` <9bac4f60-e385-fef8-0a8f-7a473b079055@pr.hu>
2018-01-04 19:21 ` Guenter Roeck
2018-01-10 8:34 ` Boszormenyi Zoltan
-- strict thread matches above, loose matches on Subject: below --
2017-12-24 21:03 [PATCH 00/12] watchdog: sp5100_tco: Various improvements Guenter Roeck
2017-12-24 21:03 ` [PATCH 01/12] watchdog: sp5100_tco: Always use SP5100_IO_PM_{INDEX_REG,DATA_REG} Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1514149457-20273-2-git-send-email-linux@roeck-us.net \
--to=linux@roeck-us.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=wim@iguana.be \
--cc=zboszor@pr.hu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).