From: Icenowy Zheng <icenowy@aosc.io>
To: Alan Stern <stern@rowland.harvard.edu>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Hans de Goede <hdegoede@redhat.com>
Cc: usb-storage@lists.one-eyed-alien.net,
linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com,
Icenowy Zheng <icenowy@aosc.io>,
stable@vger.kernel.org
Subject: [PATCH] uas: ignore UAS for Norelsys NS1068(X) chips
Date: Sat, 6 Jan 2018 00:56:44 +0800 [thread overview]
Message-ID: <20180105165644.62433-1-icenowy@aosc.io> (raw)
The UAS mode of Norelsys NS1068(X) is reported to fail to work on
several platforms with the following error message:
xhci-hcd xhci-hcd.0.auto: ERROR Transfer event for unknown stream ring slot 1 ep 8
xhci-hcd xhci-hcd.0.auto: @00000000bf04a400 00000000 00000000 1b000000 01098001
And when trying to mount a partition on the disk the disk will
disconnect from the USB controller, then after re-connecting the device
will be offlined and not working at all.
Falling back to USB mass storage can solve this problem, so ignore UAS
function of this chip.
Cc: stable@vger.kernel.org
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
The NS1066 chip from the same vendor seems to also suffer from this
problem (its USB ID is 2537:1066) according to the report of Armbian
community. However I don't have such device (I have a USB HDD enclosure
with USB ID 2537:1066, but it doesn't report UAS function at all; as
it's
The `lsusb -v` result of my NS1068X is shown below:
Bus 004 Device 002: ID 2537:1068
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x2537
idProduct 0x1068
bcdDevice 1.00
iManufacturer 1 Norelsys
iProduct 2 NS1068
iSerial 3 0123456789ABCDE
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 121
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8
bInterfaceSubClass 6
bInterfaceProtocol 80
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 8
bInterfaceSubClass 6
bInterfaceProtocol 98
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 8
Status pipe (0x02)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Command pipe (0x01)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 8
Data-in pipe (0x03)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 8
Data-out pipe (0x04)
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
HIRD Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 2047 micro seconds
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
drivers/usb/storage/unusual_uas.h | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h
index 9c2ee55ad32e..38434d88954a 100644
--- a/drivers/usb/storage/unusual_uas.h
+++ b/drivers/usb/storage/unusual_uas.h
@@ -80,6 +80,13 @@ UNUSUAL_DEV(0x2109, 0x0711, 0x0000, 0x9999,
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_NO_ATA_1X),
+/* Reported-by: Icenowy Zheng <icenowy@aosc.io> */
+UNUSUAL_DEV(0x2537, 0x1068, 0x0000, 0x9999,
+ "Norelsys",
+ "NS1068X",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_IGNORE_UAS),
+
/* Reported-by: Takeo Nakayama <javhera@gmx.com> */
UNUSUAL_DEV(0x357d, 0x7788, 0x0000, 0x9999,
"JMicron",
--
2.14.2
next reply other threads:[~2018-01-05 16:57 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-05 16:56 Icenowy Zheng [this message]
2018-01-06 22:12 ` [PATCH] uas: ignore UAS for Norelsys NS1068(X) chips Hans de Goede
2018-01-06 22:26 ` [linux-sunxi] " Icenowy Zheng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180105165644.62433-1-icenowy@aosc.io \
--to=icenowy@aosc.io \
--cc=gregkh@linuxfoundation.org \
--cc=hdegoede@redhat.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=stable@vger.kernel.org \
--cc=stern@rowland.harvard.edu \
--cc=usb-storage@lists.one-eyed-alien.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).