From: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
To: johan@kernel.org
Cc: gregkh@linuxfoundation.org, linux-usb@vger.kernel.org,
linux-kernel@vger.kernel.org, peter_hong@fintek.com.tw,
"Ji-Ze Hong (Peter Hong)" <hpeter+linux_kernel@gmail.com>
Subject: [PATCH V3 2/6] usb: serial: f81534: add auto RTS direction support
Date: Thu, 11 Jan 2018 14:47:16 +0800 [thread overview]
Message-ID: <1515653240-5420-2-git-send-email-hpeter+linux_kernel@gmail.com> (raw)
In-Reply-To: <1515653240-5420-1-git-send-email-hpeter+linux_kernel@gmail.com>
The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
---
V3:
1: change some BIT() operation to GENMASK().
2: change some dev_info() to dev_dbg().
V2:
1: Read the configure data from flash and save it to shadow clock
register.
drivers/usb/serial/f81534.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 1563d3f34381..2201be577dd3 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -98,11 +98,16 @@
#define F81534_DEFAULT_BAUD_RATE 9600
+#define F81534_PORT_CONF_RS232 0
+#define F81534_PORT_CONF_RS485 BIT(0)
+#define F81534_PORT_CONF_RS485_INVERT GENMASK(1, 0)
#define F81534_PORT_CONF_DISABLE_PORT BIT(3)
#define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7)
#define F81534_PORT_UNAVAILABLE \
(F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
+#define F81534_UART_MODE_MASK GENMASK(1, 0)
+
#define F81534_1X_RXTRIGGER 0xc3
#define F81534_8X_RXTRIGGER 0xcf
@@ -115,6 +120,8 @@
* 01: 18.46MHz.
* 10: 24MHz.
* 11: 14.77MHz.
+ * Bit4: Auto direction(RTS) control (RTS pin Low when TX)
+ * Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
*/
#define F81534_UART_EN BIT(0)
@@ -123,6 +130,8 @@
#define F81534_CLK_24_MHZ BIT(2)
#define F81534_CLK_14_77_MHZ GENMASK(2, 1)
#define F81534_CLK_MASK GENMASK(2, 1)
+#define F81534_CLK_RS485_MODE BIT(4)
+#define F81534_CLK_RS485_INVERT BIT(5)
static const struct usb_device_id f81534_id_table[] = {
{ USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
@@ -1274,9 +1283,12 @@ static void f81534_lsr_worker(struct work_struct *work)
static int f81534_port_probe(struct usb_serial_port *port)
{
+ struct f81534_serial_private *serial_priv;
struct f81534_port_private *port_priv;
int ret;
+ u8 value;
+ serial_priv = usb_get_serial_data(port->serial);
port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL);
if (!port_priv)
return -ENOMEM;
@@ -1309,6 +1321,24 @@ static int f81534_port_probe(struct usb_serial_port *port)
if (ret)
return ret;
+ value = serial_priv->conf_data[port_priv->phy_num];
+ switch (value & F81534_UART_MODE_MASK) {
+ case F81534_PORT_CONF_RS485_INVERT:
+ port_priv->shadow_clk |= F81534_CLK_RS485_MODE |
+ F81534_CLK_RS485_INVERT;
+ dev_dbg(&port->dev, "RS485 invert mode.\n");
+ break;
+ case F81534_PORT_CONF_RS485:
+ port_priv->shadow_clk |= F81534_CLK_RS485_MODE;
+ dev_dbg(&port->dev, "RS485 mode.\n");
+ break;
+
+ default:
+ case F81534_PORT_CONF_RS232:
+ dev_dbg(&port->dev, "RS232 mode.\n");
+ break;
+ }
+
return 0;
}
--
2.7.4
next prev parent reply other threads:[~2018-01-11 6:48 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-11 6:47 [PATCH V3 1/6] usb: serial: f81534: add high baud rate support Ji-Ze Hong (Peter Hong)
2018-01-11 6:47 ` Ji-Ze Hong (Peter Hong) [this message]
2018-01-11 10:05 ` [PATCH V3 2/6] usb: serial: f81534: add auto RTS direction support Johan Hovold
2018-01-11 6:47 ` [PATCH V3 3/6] usb: serial: f81534: add output pin control Ji-Ze Hong (Peter Hong)
2018-01-11 6:47 ` [PATCH V3 4/6] usb: serial: f81534: refactoring calc_num_ports() Ji-Ze Hong (Peter Hong)
2018-01-11 6:47 ` [PATCH V3 5/6] usb: serial: f81534: add H/W disable port support Ji-Ze Hong (Peter Hong)
2018-01-11 6:47 ` [PATCH V3 6/6] usb: serial: f81534: fix tx error on some baud rate Ji-Ze Hong (Peter Hong)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1515653240-5420-2-git-send-email-hpeter+linux_kernel@gmail.com \
--to=hpeter@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=hpeter+linux_kernel@gmail.com \
--cc=johan@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=peter_hong@fintek.com.tw \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).