[PATCH v1 4/8] dmaengine: stm32-dma: fix DMA IRQ status handling - Pierre-Yves MORDRET

From: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
To: Vinod Koul <vinod.koul@intel.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Maxime Coquelin <mcoquelin.stm32@gmail.com>,
	Alexandre Torgue <alexandre.torgue@st.com>,
	Dan Williams <dan.j.williams@intel.com>,
	"M'boumba Cedric Madianga" <cedric.madianga@gmail.com>,
	<dmaengine@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>
Cc: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Subject: [PATCH v1 4/8] dmaengine: stm32-dma: fix DMA IRQ status handling
Date: Tue, 13 Mar 2018 17:42:03 +0100	[thread overview]
Message-ID: <1520959327-25760-5-git-send-email-pierre-yves.mordret@st.com> (raw)
In-Reply-To: <1520959327-25760-1-git-send-email-pierre-yves.mordret@st.com>

Update the way Transfer Complete and Half Transfer Complete status are
acknowledge. Even if HTI is not enabled its status is shown when reading
registers, driver has to clear it gently and not raise an error.

Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
---
  Version history:
    v1:
       * Initial
---
---
 drivers/dma/stm32-dma.c | 29 +++++++++++++++++++++++++----
 1 file changed, 25 insertions(+), 4 deletions(-)

diff --git a/drivers/dma/stm32-dma.c b/drivers/dma/stm32-dma.c
index a7edd6d..0685961 100644
--- a/drivers/dma/stm32-dma.c
+++ b/drivers/dma/stm32-dma.c
@@ -34,9 +34,14 @@
 #define STM32_DMA_LIFCR			0x0008 /* DMA Low Int Flag Clear Reg */
 #define STM32_DMA_HIFCR			0x000c /* DMA High Int Flag Clear Reg */
 #define STM32_DMA_TCI			BIT(5) /* Transfer Complete Interrupt */
+#define STM32_DMA_HTI			BIT(4) /* Half Transfer Interrupt */
 #define STM32_DMA_TEI			BIT(3) /* Transfer Error Interrupt */
 #define STM32_DMA_DMEI			BIT(2) /* Direct Mode Error Interrupt */
 #define STM32_DMA_FEI			BIT(0) /* FIFO Error Interrupt */
+#define STM32_DMA_MASKI			(STM32_DMA_TCI \
+					 | STM32_DMA_TEI \
+					 | STM32_DMA_DMEI \
+					 | STM32_DMA_FEI)
 
 /* DMA Stream x Configuration Register */
 #define STM32_DMA_SCR(x)		(0x0010 + 0x18 * (x)) /* x = 0..7 */
@@ -637,13 +642,29 @@ static irqreturn_t stm32_dma_chan_irq(int irq, void *devid)
 	status = stm32_dma_irq_status(chan);
 	scr = stm32_dma_read(dmadev, STM32_DMA_SCR(chan->id));
 
-	if ((status & STM32_DMA_TCI) && (scr & STM32_DMA_SCR_TCIE)) {
+	if (status & STM32_DMA_TCI) {
 		stm32_dma_irq_clear(chan, STM32_DMA_TCI);
-		stm32_dma_handle_chan_done(chan);
-
-	} else {
+		if (scr & STM32_DMA_SCR_TCIE)
+			stm32_dma_handle_chan_done(chan);
+		status &= ~STM32_DMA_TCI;
+	}
+	if (status & STM32_DMA_HTI) {
+		stm32_dma_irq_clear(chan, STM32_DMA_HTI);
+		status &= ~STM32_DMA_HTI;
+	}
+	if (status & STM32_DMA_FEI) {
+		stm32_dma_irq_clear(chan, STM32_DMA_FEI);
+		status &= ~STM32_DMA_FEI;
+		if (!(scr & STM32_DMA_SCR_EN))
+			dev_err(chan2dev(chan), "FIFO Error\n");
+		else
+			dev_dbg(chan2dev(chan), "FIFO over/underrun\n");
+	}
+	if (status) {
 		stm32_dma_irq_clear(chan, status);
 		dev_err(chan2dev(chan), "DMA error: status=0x%08x\n", status);
+		if (!(scr & STM32_DMA_SCR_EN))
+			dev_err(chan2dev(chan), "chan disabled by HW\n");
 	}
 
 	spin_unlock(&chan->vchan.lock);
-- 
2.7.4
