From: "Clément Péron" <peron.clem@gmail.com>
To: Colin Didier <colin.didier@devialet.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: "Stefan Agner" <stefan@agner.ch>,
"Daniel Lezcano" <daniel.lezcano@linaro.org>,
"Thomas Gleixner" <tglx@linutronix.de>,
"Fabio Estevam" <fabio.estevam@nxp.com>,
"Vladimir Zapolskiy" <vladimir_zapolskiy@mentor.com>,
"Sascha Hauer" <s.hauer@pengutronix.de>,
"Rob Herring" <robh@kernel.org>,
"NXP Linux Team" <linux-imx@nxp.com>,
"Pengutronix Kernel Team" <kernel@pengutronix.de>,
"Clément Peron" <clement.peron@devialet.com>
Subject: [PATCH v7 4/5] clocksource: add driver for i.MX EPIT timer
Date: Mon, 11 Jun 2018 17:50:00 +0200 [thread overview]
Message-ID: <20180611155001.3506-5-peron.clem@gmail.com> (raw)
In-Reply-To: <20180611155001.3506-1-peron.clem@gmail.com>
From: Colin Didier <colin.didier@devialet.com>
Add driver for NXP's EPIT timer used in i.MX SoC.
Signed-off-by: Colin Didier <colin.didier@devialet.com>
Signed-off-by: Clément Peron <clement.peron@devialet.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
---
drivers/clocksource/Kconfig | 11 ++
drivers/clocksource/Makefile | 1 +
drivers/clocksource/timer-imx-epit.c | 265 +++++++++++++++++++++++++++
3 files changed, 277 insertions(+)
create mode 100644 drivers/clocksource/timer-imx-epit.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 8e8a09755d10..790478afd02c 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -576,6 +576,17 @@ config H8300_TPU
This enables the clocksource for the H8300 platform with the
H8S2678 cpu.
+config CLKSRC_IMX_EPIT
+ bool "Clocksource using i.MX EPIT"
+ depends on CLKDEV_LOOKUP && (ARCH_MXC || COMPILE_TEST)
+ select CLKSRC_MMIO
+ help
+ This enables EPIT support available on some i.MX platforms.
+ Normally you don't have a reason to do so as the EPIT has
+ the same features and uses the same clocks as the GPT.
+ Anyway, on some systems the GPT may be in use for other
+ purposes.
+
config CLKSRC_IMX_GPT
bool "Clocksource using i.MX GPT" if COMPILE_TEST
depends on ARM && CLKDEV_LOOKUP
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 00caf37e52f9..d9426f69ec69 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_INTEGRATOR_AP_TIMER) += timer-integrator-ap.o
obj-$(CONFIG_CLKSRC_VERSATILE) += versatile.o
obj-$(CONFIG_CLKSRC_MIPS_GIC) += mips-gic-timer.o
obj-$(CONFIG_CLKSRC_TANGO_XTAL) += tango_xtal.o
+obj-$(CONFIG_CLKSRC_IMX_EPIT) += timer-imx-epit.o
obj-$(CONFIG_CLKSRC_IMX_GPT) += timer-imx-gpt.o
obj-$(CONFIG_CLKSRC_IMX_TPM) += timer-imx-tpm.o
obj-$(CONFIG_ASM9260_TIMER) += asm9260_timer.o
diff --git a/drivers/clocksource/timer-imx-epit.c b/drivers/clocksource/timer-imx-epit.c
new file mode 100644
index 000000000000..7f1c8e2e00aa
--- /dev/null
+++ b/drivers/clocksource/timer-imx-epit.c
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * i.MX EPIT Timer
+ *
+ * Copyright (C) 2010 Sascha Hauer <s.hauer@pengutronix.de>
+ * Copyright (C) 2018 Colin Didier <colin.didier@devialet.com>
+ * Copyright (C) 2018 Clément Péron <clement.peron@devialet.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/sched_clock.h>
+#include <linux/slab.h>
+
+#define EPITCR 0x00
+#define EPITSR 0x04
+#define EPITLR 0x08
+#define EPITCMPR 0x0c
+#define EPITCNR 0x10
+
+#define EPITCR_EN BIT(0)
+#define EPITCR_ENMOD BIT(1)
+#define EPITCR_OCIEN BIT(2)
+#define EPITCR_RLD BIT(3)
+#define EPITCR_PRESC(x) (((x) & 0xfff) << 4)
+#define EPITCR_SWR BIT(16)
+#define EPITCR_IOVW BIT(17)
+#define EPITCR_DBGEN BIT(18)
+#define EPITCR_WAITEN BIT(19)
+#define EPITCR_RES BIT(20)
+#define EPITCR_STOPEN BIT(21)
+#define EPITCR_OM_DISCON (0 << 22)
+#define EPITCR_OM_TOGGLE (1 << 22)
+#define EPITCR_OM_CLEAR (2 << 22)
+#define EPITCR_OM_SET (3 << 22)
+#define EPITCR_CLKSRC_OFF (0 << 24)
+#define EPITCR_CLKSRC_PERIPHERAL (1 << 24)
+#define EPITCR_CLKSRC_REF_HIGH (2 << 24)
+#define EPITCR_CLKSRC_REF_LOW (3 << 24)
+
+#define EPITSR_OCIF BIT(0)
+
+struct epit_timer {
+ void __iomem *base;
+ int irq;
+ struct clk *clk;
+ struct clock_event_device ced;
+ struct irqaction act;
+};
+
+static void __iomem *sched_clock_reg;
+
+static inline struct epit_timer *to_epit_timer(struct clock_event_device *ced)
+{
+ return container_of(ced, struct epit_timer, ced);
+}
+
+static inline void epit_irq_disable(struct epit_timer *epittm)
+{
+ u32 val;
+
+ val = readl_relaxed(epittm->base + EPITCR);
+ writel_relaxed(val & ~EPITCR_OCIEN, epittm->base + EPITCR);
+}
+
+static inline void epit_irq_enable(struct epit_timer *epittm)
+{
+ u32 val;
+
+ val = readl_relaxed(epittm->base + EPITCR);
+ writel_relaxed(val | EPITCR_OCIEN, epittm->base + EPITCR);
+}
+
+static void epit_irq_acknowledge(struct epit_timer *epittm)
+{
+ writel_relaxed(EPITSR_OCIF, epittm->base + EPITSR);
+}
+
+static u64 notrace epit_read_sched_clock(void)
+{
+ return ~readl_relaxed(sched_clock_reg);
+}
+
+static int epit_set_next_event(unsigned long cycles,
+ struct clock_event_device *ced)
+{
+ struct epit_timer *epittm = to_epit_timer(ced);
+ unsigned long tcmp;
+
+ tcmp = readl_relaxed(epittm->base + EPITCNR) - cycles;
+ writel_relaxed(tcmp, epittm->base + EPITCMPR);
+
+ return 0;
+}
+
+/* Left event sources disabled, no more interrupts appear */
+static int epit_shutdown(struct clock_event_device *ced)
+{
+ struct epit_timer *epittm = to_epit_timer(ced);
+ unsigned long flags;
+
+ /*
+ * The timer interrupt generation is disabled at least
+ * for enough time to call epit_set_next_event()
+ */
+ local_irq_save(flags);
+
+ /* Disable interrupt in EPIT module */
+ epit_irq_disable(epittm);
+
+ /* Clear pending interrupt */
+ epit_irq_acknowledge(epittm);
+
+ local_irq_restore(flags);
+
+ return 0;
+}
+
+static int epit_set_oneshot(struct clock_event_device *ced)
+{
+ struct epit_timer *epittm = to_epit_timer(ced);
+ unsigned long flags;
+
+ /*
+ * The timer interrupt generation is disabled at least
+ * for enough time to call epit_set_next_event()
+ */
+ local_irq_save(flags);
+
+ /* Disable interrupt in EPIT module */
+ epit_irq_disable(epittm);
+
+ /* Clear pending interrupt, only while switching mode */
+ if (!clockevent_state_oneshot(ced))
+ epit_irq_acknowledge(epittm);
+
+ /*
+ * Do not put overhead of interrupt enable/disable into
+ * epit_set_next_event(), the core has about 4 minutes
+ * to call epit_set_next_event() or shutdown clock after
+ * mode switching
+ */
+ epit_irq_enable(epittm);
+ local_irq_restore(flags);
+
+ return 0;
+}
+
+static irqreturn_t epit_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *ced = dev_id;
+ struct epit_timer *epittm = to_epit_timer(ced);
+
+ epit_irq_acknowledge(epittm);
+
+ ced->event_handler(ced);
+
+ return IRQ_HANDLED;
+}
+
+static int __init epit_clocksource_init(struct epit_timer *epittm)
+{
+ unsigned int c = clk_get_rate(epittm->clk);
+
+ sched_clock_reg = epittm->base + EPITCNR;
+ sched_clock_register(epit_read_sched_clock, 32, c);
+
+ return clocksource_mmio_init(epittm->base + EPITCNR, "epit", c, 200, 32,
+ clocksource_mmio_readl_down);
+}
+
+static int __init epit_clockevent_init(struct epit_timer *epittm)
+{
+ struct clock_event_device *ced = &epittm->ced;
+ struct irqaction *act = &epittm->act;
+
+ ced->name = "epit";
+ ced->features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_DYNIRQ;
+ ced->set_state_shutdown = epit_shutdown;
+ ced->tick_resume = epit_shutdown;
+ ced->set_state_oneshot = epit_set_oneshot;
+ ced->set_next_event = epit_set_next_event;
+ ced->rating = 200;
+ ced->cpumask = cpumask_of(0);
+ ced->irq = epittm->irq;
+ clockevents_config_and_register(ced, clk_get_rate(epittm->clk),
+ 0xff, 0xfffffffe);
+
+ act->name = "i.MX EPIT Timer Tick",
+ act->flags = IRQF_TIMER | IRQF_IRQPOLL;
+ act->handler = epit_timer_interrupt;
+ act->dev_id = ced;
+
+ /* Make irqs happen */
+ return setup_irq(epittm->irq, act);
+}
+
+static int __init epit_timer_init(struct device_node *np)
+{
+ struct epit_timer *epittm;
+ int ret;
+
+ epittm = kzalloc(sizeof(*epittm), GFP_KERNEL);
+ if (!epittm)
+ return -ENOMEM;
+
+ epittm->base = of_iomap(np, 0);
+ if (!epittm->base) {
+ ret = -ENXIO;
+ goto out_kfree;
+ }
+
+ epittm->irq = irq_of_parse_and_map(np, 0);
+ if (!epittm->irq) {
+ ret = -EINVAL;
+ goto out_iounmap;
+ }
+
+ /* Get EPIT clock */
+ epittm->clk = of_clk_get(np, 0);
+ if (IS_ERR(epittm->clk)) {
+ pr_err("i.MX EPIT: unable to get clk\n");
+ ret = PTR_ERR(epittm->clk);
+ goto out_iounmap;
+ }
+
+ ret = clk_prepare_enable(epittm->clk);
+ if (ret) {
+ pr_err("i.MX EPIT: unable to prepare+enable clk\n");
+ goto out_iounmap;
+ }
+
+ /* Initialise to a known state (all timers off, and timing reset) */
+ writel_relaxed(0x0, epittm->base + EPITCR);
+ writel_relaxed(0xffffffff, epittm->base + EPITLR);
+ writel_relaxed(EPITCR_EN | EPITCR_CLKSRC_REF_HIGH | EPITCR_WAITEN,
+ epittm->base + EPITCR);
+
+ ret = epit_clocksource_init(epittm);
+ if (ret) {
+ pr_err("i.MX EPIT: failed to init clocksource\n");
+ goto out_clk_disable;
+ }
+
+ ret = epit_clockevent_init(epittm);
+ if (ret) {
+ pr_err("i.MX EPIT: failed to init clockevent\n");
+ goto out_clk_disable;
+ }
+
+ return 0;
+
+out_clk_disable:
+ clk_disable_unprepare(epittm->clk);
+out_iounmap:
+ iounmap(epittm->base);
+out_kfree:
+ kfree(epittm);
+
+ return ret;
+}
+TIMER_OF_DECLARE(epit_timer, "fsl,imx31-epit", epit_timer_init);
--
2.17.1
next prev parent reply other threads:[~2018-06-11 15:51 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-11 15:49 [PATCH v7 0/5] Reintroduce i.MX EPIT Timer Clément Péron
2018-06-11 15:49 ` [PATCH v7 1/5] clk: imx6: add EPIT clock support Clément Péron
2018-06-11 15:49 ` [PATCH v7 2/5] ARM: imx: remove inexistant EPIT timer init Clément Péron
2018-06-11 15:49 ` [PATCH v7 3/5] dt-bindings: timer: add i.MX EPIT timer binding Clément Péron
2018-06-12 18:27 ` Rob Herring
2018-06-11 15:50 ` Clément Péron [this message]
2018-07-10 16:20 ` [PATCH v7 4/5] clocksource: add driver for i.MX EPIT timer Daniel Lezcano
2018-11-04 16:07 ` Clément Péron
2018-11-05 11:48 ` Daniel Lezcano
2018-11-08 13:25 ` Clément Péron
2018-06-11 15:50 ` [PATCH v7 5/5] ARM: dts: imx: add missing compatible and clock properties for EPIT Clément Péron
2018-07-10 14:55 ` [PATCH v7 0/5] Reintroduce i.MX EPIT Timer Clément Péron
2018-07-10 14:58 ` Daniel Lezcano
2018-07-10 15:12 ` Daniel Lezcano
2018-07-10 15:22 ` Clément Péron
2018-07-10 15:37 ` Daniel Lezcano
2018-07-10 16:05 ` Clément Péron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180611155001.3506-5-peron.clem@gmail.com \
--to=peron.clem@gmail.com \
--cc=clement.peron@devialet.com \
--cc=colin.didier@devialet.com \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=stefan@agner.ch \
--cc=tglx@linutronix.de \
--cc=vladimir_zapolskiy@mentor.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).