From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: mturquette@baylibre.com, sboyd@kernel.org, robh+dt@kernel.org,
mark.rutland@arm.com, lee.jones@linaro.org, lgirdwood@gmail.com,
broonie@kernel.org, mazziesaccount@gmail.com, arnd@arndb.de,
dmitry.torokhov@gmail.com, sre@kernel.org, chenjh@rock-chips.com,
andrew.smirnov@gmail.com, linus.walleij@linaro.org,
kstewart@linuxfoundation.org, heiko@sntech.de,
gregkh@linuxfoundation.org
Cc: linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-input@vger.kernel.org,
mikko.mutanen@fi.rohmeurope.com,
heikki.haikola@fi.rohmeurope.com
Subject: [PATCH v7 1/4] mfd: bd71837: mfd driver for ROHM BD71837 PMIC
Date: Tue, 19 Jun 2018 13:55:54 +0300 [thread overview]
Message-ID: <7e1888375c979accc402e9ddd7316e528b2ac52c.1529404894.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1529404894.git.matti.vaittinen@fi.rohmeurope.com>
ROHM BD71837 PMIC MFD driver providing interrupts and support
for two subsystems:
- clk
- Regulators
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
drivers/mfd/Kconfig | 13 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/bd71837.c | 221 ++++++++++++++++++++++++++
include/linux/mfd/bd71837.h | 367 ++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 602 insertions(+)
create mode 100644 drivers/mfd/bd71837.c
create mode 100644 include/linux/mfd/bd71837.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b860eb5aa194..7aa05fc9ed8e 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1787,6 +1787,19 @@ config MFD_STW481X
in various ST Microelectronics and ST-Ericsson embedded
Nomadik series.
+config MFD_BD71837
+ bool "BD71837 Power Management chip"
+ depends on I2C=y
+ depends on OF
+ select REGMAP_I2C
+ select REGMAP_IRQ
+ select MFD_CORE
+ help
+ Select this option to get support for the ROHM BD71837
+ Power Management chips. BD71837 is designed to power processors like
+ NXP i.MX8. It contains 8 BUCK outputs and 7 LDOs, voltage monitoring
+ and emergency shut down as well as 32,768KHz clock output.
+
config MFD_STM32_LPTIMER
tristate "Support for STM32 Low-Power Timer"
depends on (ARCH_STM32 && OF) || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index e9fd20dba18d..09dc9eb3782c 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -227,4 +227,5 @@ obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
obj-$(CONFIG_MFD_MXS_LRADC) += mxs-lradc.o
obj-$(CONFIG_MFD_SC27XX_PMIC) += sprd-sc27xx-spi.o
obj-$(CONFIG_RAVE_SP_CORE) += rave-sp.o
+obj-$(CONFIG_MFD_BD71837) += bd71837.o
diff --git a/drivers/mfd/bd71837.c b/drivers/mfd/bd71837.c
new file mode 100644
index 000000000000..0f0361d6cad6
--- /dev/null
+++ b/drivers/mfd/bd71837.c
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+// bd71837.c -- ROHM BD71837MWV mfd driver
+//
+// Datasheet available from
+// https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/gpio.h>
+#include <linux/regmap.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/bd71837.h>
+
+static const struct resource irqs[] = {
+ {
+ .start = BD71837_INT_PWRBTN,
+ .end = BD71837_INT_PWRBTN,
+ .flags = IORESOURCE_IRQ,
+ .name = "pwr-btn",
+ }, {
+ .start = BD71837_INT_PWRBTN_L,
+ .end = BD71837_INT_PWRBTN_L,
+ .flags = IORESOURCE_IRQ,
+ .name = "pwr-btn-l",
+ }, {
+ .start = BD71837_INT_PWRBTN_S,
+ .end = BD71837_INT_PWRBTN_S,
+ .flags = IORESOURCE_IRQ,
+ .name = "pwr-btn-s",
+ },
+};
+
+/* bd71837 multi function cells */
+static struct mfd_cell bd71837_mfd_cells[] = {
+ {
+ .name = "bd71837-clk",
+ }, {
+ .name = "bd718xx-pwrkey",
+ .resources = &irqs[0],
+ .num_resources = ARRAY_SIZE(irqs),
+ }, {
+ .name = "bd71837-pmic",
+ },
+};
+
+static const struct regmap_irq bd71837_irqs[] = {
+ REGMAP_IRQ_REG(BD71837_INT_SWRST, 0, BD71837_INT_SWRST_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_PWRBTN_S, 0, BD71837_INT_PWRBTN_S_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_PWRBTN_L, 0, BD71837_INT_PWRBTN_L_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_PWRBTN, 0, BD71837_INT_PWRBTN_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_WDOG, 0, BD71837_INT_WDOG_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_ON_REQ, 0, BD71837_INT_ON_REQ_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_STBY_REQ, 0, BD71837_INT_STBY_REQ_MASK),
+};
+
+static struct regmap_irq_chip bd71837_irq_chip = {
+ .name = "bd71837-irq",
+ .irqs = bd71837_irqs,
+ .num_irqs = ARRAY_SIZE(bd71837_irqs),
+ .num_regs = 1,
+ .irq_reg_stride = 1,
+ .status_base = BD71837_REG_IRQ,
+ .mask_base = BD71837_REG_MIRQ,
+ .ack_base = BD71837_REG_IRQ,
+ .init_ack_masked = true,
+ .mask_invert = false,
+};
+
+static int bd71837_irq_exit(struct bd71837 *bd71837)
+{
+ if (bd71837->chip_irq > 0)
+ regmap_del_irq_chip(bd71837->chip_irq, bd71837->irq_data);
+ return 0;
+}
+
+static const struct regmap_range pmic_status_range = {
+ .range_min = BD71837_REG_IRQ,
+ .range_max = BD71837_REG_POW_STATE,
+};
+
+static const struct regmap_access_table volatile_regs = {
+ .yes_ranges = &pmic_status_range,
+ .n_yes_ranges = 1,
+};
+
+static const struct regmap_config bd71837_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .volatile_table = &volatile_regs,
+ .max_register = BD71837_MAX_REGISTER - 1,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+#ifdef CONFIG_OF
+static const struct of_device_id bd71837_of_match[] = {
+ { .compatible = "rohm,bd71837", .data = (void *)0},
+ { },
+};
+MODULE_DEVICE_TABLE(of, bd71837_of_match);
+#endif //CONFIG_OF
+
+static int bd71837_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct bd71837 *bd71837;
+ struct bd71837_board *board_info;
+ int ret = -EINVAL;
+
+ board_info = dev_get_platdata(&i2c->dev);
+
+ if (!board_info) {
+ board_info = devm_kzalloc(&i2c->dev, sizeof(*board_info),
+ GFP_KERNEL);
+ if (!board_info) {
+ ret = -ENOMEM;
+ goto err_out;
+ } else if (i2c->irq) {
+ board_info->gpio_intr = i2c->irq;
+ } else {
+ ret = -ENOENT;
+ goto err_out;
+ }
+ }
+
+ if (!board_info)
+ goto err_out;
+
+ bd71837 = devm_kzalloc(&i2c->dev, sizeof(struct bd71837), GFP_KERNEL);
+ if (bd71837 == NULL)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, bd71837);
+ bd71837->dev = &i2c->dev;
+ bd71837->i2c_client = i2c;
+ bd71837->chip_irq = board_info->gpio_intr;
+
+ bd71837->regmap = devm_regmap_init_i2c(i2c, &bd71837_regmap_config);
+ if (IS_ERR(bd71837->regmap)) {
+ ret = PTR_ERR(bd71837->regmap);
+ dev_err(&i2c->dev, "regmap initialization failed: %d\n", ret);
+ goto err_out;
+ }
+
+ ret = bd71837_reg_read(bd71837, BD71837_REG_REV);
+ if (ret < 0) {
+ dev_err(bd71837->dev,
+ "%s(): Read BD71837_REG_DEVICE failed!\n", __func__);
+ goto err_out;
+ }
+
+ ret = regmap_add_irq_chip(bd71837->regmap, bd71837->chip_irq,
+ IRQF_ONESHOT, 0,
+ &bd71837_irq_chip, &bd71837->irq_data);
+ if (ret < 0) {
+ dev_err(bd71837->dev, "Failed to add irq_chip %d\n", ret);
+ goto err_out;
+ }
+
+ ret = mfd_add_devices(bd71837->dev, PLATFORM_DEVID_AUTO,
+ bd71837_mfd_cells, ARRAY_SIZE(bd71837_mfd_cells),
+ NULL, 0,
+ regmap_irq_get_domain(bd71837->irq_data));
+ if (ret)
+ regmap_del_irq_chip(bd71837->chip_irq, bd71837->irq_data);
+err_out:
+
+ return ret;
+}
+
+static int bd71837_i2c_remove(struct i2c_client *i2c)
+{
+ struct bd71837 *bd71837 = i2c_get_clientdata(i2c);
+
+ bd71837_irq_exit(bd71837);
+ mfd_remove_devices(bd71837->dev);
+
+ return 0;
+}
+
+static const struct i2c_device_id bd71837_i2c_id[] = {
+ { .name = "bd71837", },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, bd71837_i2c_id);
+
+static struct i2c_driver bd71837_i2c_driver = {
+ .driver = {
+ .name = "bd71837-mfd",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(bd71837_of_match),
+ },
+ .probe = bd71837_i2c_probe,
+ .remove = bd71837_i2c_remove,
+ .id_table = bd71837_i2c_id,
+};
+
+static int __init bd71837_i2c_init(void)
+{
+ return i2c_add_driver(&bd71837_i2c_driver);
+}
+/* init early so consumer devices can complete system boot */
+subsys_initcall(bd71837_i2c_init);
+
+static void __exit bd71837_i2c_exit(void)
+{
+ i2c_del_driver(&bd71837_i2c_driver);
+}
+module_exit(bd71837_i2c_exit);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71837 chip multi-function driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/bd71837.h b/include/linux/mfd/bd71837.h
new file mode 100644
index 000000000000..125c7478ec29
--- /dev/null
+++ b/include/linux/mfd/bd71837.h
@@ -0,0 +1,367 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 ROHM Semiconductors */
+
+/*
+ * ROHM BD71837MWV header file
+ */
+
+#ifndef __LINUX_MFD_BD71837_H__
+#define __LINUX_MFD_BD71837_H__
+
+#include <linux/regmap.h>
+
+enum {
+ BD71837_BUCK1 = 0,
+ BD71837_BUCK2,
+ BD71837_BUCK3,
+ BD71837_BUCK4,
+ BD71837_BUCK5,
+ BD71837_BUCK6,
+ BD71837_BUCK7,
+ BD71837_BUCK8,
+ BD71837_LDO1,
+ BD71837_LDO2,
+ BD71837_LDO3,
+ BD71837_LDO4,
+ BD71837_LDO5,
+ BD71837_LDO6,
+ BD71837_LDO7,
+ BD71837_REGULATOR_CNT,
+};
+
+#define BD71837_BUCK1_VOLTAGE_NUM 0x40
+#define BD71837_BUCK2_VOLTAGE_NUM 0x40
+#define BD71837_BUCK3_VOLTAGE_NUM 0x40
+#define BD71837_BUCK4_VOLTAGE_NUM 0x40
+
+#define BD71837_BUCK5_VOLTAGE_NUM 0x08
+#define BD71837_BUCK6_VOLTAGE_NUM 0x04
+#define BD71837_BUCK7_VOLTAGE_NUM 0x08
+#define BD71837_BUCK8_VOLTAGE_NUM 0x40
+
+#define BD71837_LDO1_VOLTAGE_NUM 0x04
+#define BD71837_LDO2_VOLTAGE_NUM 0x02
+#define BD71837_LDO3_VOLTAGE_NUM 0x10
+#define BD71837_LDO4_VOLTAGE_NUM 0x10
+#define BD71837_LDO5_VOLTAGE_NUM 0x10
+#define BD71837_LDO6_VOLTAGE_NUM 0x10
+#define BD71837_LDO7_VOLTAGE_NUM 0x10
+
+enum {
+ BD71837_REG_REV = 0x00,
+ BD71837_REG_SWRESET = 0x01,
+ BD71837_REG_I2C_DEV = 0x02,
+ BD71837_REG_PWRCTRL0 = 0x03,
+ BD71837_REG_PWRCTRL1 = 0x04,
+ BD71837_REG_BUCK1_CTRL = 0x05,
+ BD71837_REG_BUCK2_CTRL = 0x06,
+ BD71837_REG_BUCK3_CTRL = 0x07,
+ BD71837_REG_BUCK4_CTRL = 0x08,
+ BD71837_REG_BUCK5_CTRL = 0x09,
+ BD71837_REG_BUCK6_CTRL = 0x0A,
+ BD71837_REG_BUCK7_CTRL = 0x0B,
+ BD71837_REG_BUCK8_CTRL = 0x0C,
+ BD71837_REG_BUCK1_VOLT_RUN = 0x0D,
+ BD71837_REG_BUCK1_VOLT_IDLE = 0x0E,
+ BD71837_REG_BUCK1_VOLT_SUSP = 0x0F,
+ BD71837_REG_BUCK2_VOLT_RUN = 0x10,
+ BD71837_REG_BUCK2_VOLT_IDLE = 0x11,
+ BD71837_REG_BUCK3_VOLT_RUN = 0x12,
+ BD71837_REG_BUCK4_VOLT_RUN = 0x13,
+ BD71837_REG_BUCK5_VOLT = 0x14,
+ BD71837_REG_BUCK6_VOLT = 0x15,
+ BD71837_REG_BUCK7_VOLT = 0x16,
+ BD71837_REG_BUCK8_VOLT = 0x17,
+ BD71837_REG_LDO1_VOLT = 0x18,
+ BD71837_REG_LDO2_VOLT = 0x19,
+ BD71837_REG_LDO3_VOLT = 0x1A,
+ BD71837_REG_LDO4_VOLT = 0x1B,
+ BD71837_REG_LDO5_VOLT = 0x1C,
+ BD71837_REG_LDO6_VOLT = 0x1D,
+ BD71837_REG_LDO7_VOLT = 0x1E,
+ BD71837_REG_TRANS_COND0 = 0x1F,
+ BD71837_REG_TRANS_COND1 = 0x20,
+ BD71837_REG_VRFAULTEN = 0x21,
+ BD71837_REG_MVRFLTMASK0 = 0x22,
+ BD71837_REG_MVRFLTMASK1 = 0x23,
+ BD71837_REG_MVRFLTMASK2 = 0x24,
+ BD71837_REG_RCVCFG = 0x25,
+ BD71837_REG_RCVNUM = 0x26,
+ BD71837_REG_PWRONCONFIG0 = 0x27,
+ BD71837_REG_PWRONCONFIG1 = 0x28,
+ BD71837_REG_RESETSRC = 0x29,
+ BD71837_REG_MIRQ = 0x2A,
+ BD71837_REG_IRQ = 0x2B,
+ BD71837_REG_IN_MON = 0x2C,
+ BD71837_REG_POW_STATE = 0x2D,
+ BD71837_REG_OUT32K = 0x2E,
+ BD71837_REG_REGLOCK = 0x2F,
+ BD71837_REG_OTPVER = 0xFF,
+ BD71837_MAX_REGISTER = 0x100,
+};
+
+#define REGLOCK_PWRSEQ 0x1
+#define REGLOCK_VREG 0x10
+
+/* Generic BUCK control masks */
+#define BD71837_BUCK_SEL 0x02
+#define BD71837_BUCK_EN 0x01
+#define BD71837_BUCK_RUN_ON 0x04
+
+/* Generic LDO masks */
+#define BD71837_LDO_SEL 0x80
+#define BD71837_LDO_EN 0x40
+
+/* BD71837 BUCK ramp rate CTRL reg bits */
+#define BUCK_RAMPRATE_MASK 0xC0
+#define BUCK_RAMPRATE_10P00MV 0x0
+#define BUCK_RAMPRATE_5P00MV 0x1
+#define BUCK_RAMPRATE_2P50MV 0x2
+#define BUCK_RAMPRATE_1P25MV 0x3
+
+/* BD71837_REG_BUCK1_VOLT_RUN bits */
+#define BUCK1_RUN_MASK 0x3F
+#define BUCK1_RUN_DEFAULT 0x14
+
+/* BD71837_REG_BUCK1_VOLT_SUSP bits */
+#define BUCK1_SUSP_MASK 0x3F
+#define BUCK1_SUSP_DEFAULT 0x14
+
+/* BD71837_REG_BUCK1_VOLT_IDLE bits */
+#define BUCK1_IDLE_MASK 0x3F
+#define BUCK1_IDLE_DEFAULT 0x14
+
+/* BD71837_REG_BUCK2_VOLT_RUN bits */
+#define BUCK2_RUN_MASK 0x3F
+#define BUCK2_RUN_DEFAULT 0x1E
+
+/* BD71837_REG_BUCK2_VOLT_IDLE bits */
+#define BUCK2_IDLE_MASK 0x3F
+#define BUCK2_IDLE_DEFAULT 0x14
+
+/* BD71837_REG_BUCK3_VOLT_RUN bits */
+#define BUCK3_RUN_MASK 0x3F
+#define BUCK3_RUN_DEFAULT 0x1E
+
+/* BD71837_REG_BUCK4_VOLT_RUN bits */
+#define BUCK4_RUN_MASK 0x3F
+#define BUCK4_RUN_DEFAULT 0x1E
+
+/* BD71837_REG_BUCK5_VOLT bits */
+#define BUCK5_MASK 0x07
+#define BUCK5_DEFAULT 0x02
+
+/* BD71837_REG_BUCK6_VOLT bits */
+#define BUCK6_MASK 0x03
+#define BUCK6_DEFAULT 0x03
+
+/* BD71837_REG_BUCK7_VOLT bits */
+#define BUCK7_MASK 0x07
+#define BUCK7_DEFAULT 0x03
+
+/* BD71837_REG_BUCK8_VOLT bits */
+#define BUCK8_MASK 0x3F
+#define BUCK8_DEFAULT 0x1E
+
+/* BD71837_REG_IRQ bits */
+#define IRQ_SWRST 0x40
+#define IRQ_PWRON_S 0x20
+#define IRQ_PWRON_L 0x10
+#define IRQ_PWRON 0x08
+#define IRQ_WDOG 0x04
+#define IRQ_ON_REQ 0x02
+#define IRQ_STBY_REQ 0x01
+
+/* BD71837_REG_OUT32K bits */
+#define BD71837_OUT32K_EN 0x01
+
+/* BD71837 gated clock rate */
+#define BD71837_CLK_RATE 32768
+
+/* BD71837 irqs */
+enum {
+ BD71837_INT_STBY_REQ,
+ BD71837_INT_ON_REQ,
+ BD71837_INT_WDOG,
+ BD71837_INT_PWRBTN,
+ BD71837_INT_PWRBTN_L,
+ BD71837_INT_PWRBTN_S,
+ BD71837_INT_SWRST
+};
+
+/* BD71837 interrupt masks */
+#define BD71837_INT_SWRST_MASK 0x40
+#define BD71837_INT_PWRBTN_S_MASK 0x20
+#define BD71837_INT_PWRBTN_L_MASK 0x10
+#define BD71837_INT_PWRBTN_MASK 0x8
+#define BD71837_INT_WDOG_MASK 0x4
+#define BD71837_INT_ON_REQ_MASK 0x2
+#define BD71837_INT_STBY_REQ_MASK 0x1
+
+/* BD71837_REG_LDO1_VOLT bits */
+#define LDO1_MASK 0x03
+
+/* BD71837_REG_LDO1_VOLT bits */
+#define LDO2_MASK 0x20
+
+/* BD71837_REG_LDO3_VOLT bits */
+#define LDO3_MASK 0x0F
+
+/* BD71837_REG_LDO4_VOLT bits */
+#define LDO4_MASK 0x0F
+
+/* BD71837_REG_LDO5_VOLT bits */
+#define LDO5_MASK 0x0F
+
+/* BD71837_REG_LDO6_VOLT bits */
+#define LDO6_MASK 0x0F
+
+/* BD71837_REG_LDO7_VOLT bits */
+#define LDO7_MASK 0x0F
+
+/* register write induced reset settings */
+
+/* even though the bit zero is not SWRESET type we still want to write zero
+ * to it when changing type. Biz zero is 'SWRESET' trigger bit and if we
+ * write 1 to it we will trigger the action. So always write 0 to it when
+ * changning SWRESET action - no matter what we read from it.
+ */
+#define BD71837_SWRESET_TYPE_MASK 7
+#define BD71837_SWRESET_TYPE_DISABLED 0
+#define BD71837_SWRESET_TYPE_COLD 4
+#define BD71837_SWRESET_TYPE_WARM 6
+
+#define BD71837_SWRESET_RESET_MASK 1
+#define BD71837_SWRESET_RESET 1
+
+/* Poweroff state transition conditions */
+
+#define BD718XX_ON_REQ_POWEROFF_MASK 1
+#define BD718XX_SWRESET_POWEROFF_MASK 2
+#define BD718XX_WDOG_POWEROFF_MASK 4
+#define BD718XX_KEY_L_POWEROFF_MASK 8
+
+#define BD718XX_POWOFF_TO_SNVS 0
+#define BD718XX_POWOFF_TO_RDY 0xF
+
+#define BD718XX_POWOFF_TIME_MASK 0xF0
+enum {
+ BD718XX_POWOFF_TIME_5MS = 0,
+ BD718XX_POWOFF_TIME_10MS,
+ BD718XX_POWOFF_TIME_15MS,
+ BD718XX_POWOFF_TIME_20MS,
+ BD718XX_POWOFF_TIME_25MS,
+ BD718XX_POWOFF_TIME_30MS,
+ BD718XX_POWOFF_TIME_35MS,
+ BD718XX_POWOFF_TIME_40MS,
+ BD718XX_POWOFF_TIME_45MS,
+ BD718XX_POWOFF_TIME_50MS,
+ BD718XX_POWOFF_TIME_75MS,
+ BD718XX_POWOFF_TIME_100MS,
+ BD718XX_POWOFF_TIME_250MS,
+ BD718XX_POWOFF_TIME_500MS,
+ BD718XX_POWOFF_TIME_750MS,
+ BD718XX_POWOFF_TIME_1500MS
+};
+
+/* Poweron sequence state transition conditions */
+
+#define BD718XX_RDY_TO_SNVS_MASK 0xF
+#define BD718XX_SNVS_TO_RUN_MASK 0xF0
+
+#define BD718XX_PWR_TRIG_KEY_L 1
+#define BD718XX_PWR_TRIG_KEY_S 2
+#define BD718XX_PWR_TRIG_PMIC_ON 4
+#define BD718XX_PWR_TRIG_VSYS_UVLO 8
+#define BD718XX_RDY_TO_SNVS_SIFT 0
+#define BD718XX_SNVS_TO_RUN_SIFT 4
+
+/* Timeout value for detecting short press */
+
+#define BD718XX_PWRBTN_SHORT_PRESS_MASK 0xF
+
+enum {
+ BD718XX_PWRBTN_SHORT_PRESS_10MS = 0,
+ BD718XX_PWRBTN_SHORT_PRESS_500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_1000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_1500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_2000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_2500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_3000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_3500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_4000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_4500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_5000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_5500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_6000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_6500MS,
+ BD718XX_PWRBTN_SHORT_PRESS_7000MS,
+ BD718XX_PWRBTN_SHORT_PRESS_7500MS
+};
+
+struct bd71837;
+struct bd71837_pmic;
+struct bd71837_clk;
+struct bd718xx_pwrkey;
+
+/*
+ * Board platform data may be used to initialize regulators.
+ */
+
+struct bd71837_board {
+ struct regulator_init_data *init_data[BD71837_REGULATOR_CNT];
+ int gpio_intr;
+};
+
+struct bd71837 {
+ struct device *dev;
+ struct i2c_client *i2c_client;
+ struct regmap *regmap;
+ unsigned long int id;
+
+ int chip_irq;
+ struct regmap_irq_chip_data *irq_data;
+
+ struct bd71837_pmic *pmic;
+ struct bd71837_clk *clk;
+ struct bd718xx_pwrkey *pwrkey;
+};
+
+/*
+ * bd71837 sub-driver chip access routines
+ */
+
+static inline int bd71837_reg_read(struct bd71837 *bd71837, u8 reg)
+{
+ int r, val;
+
+ r = regmap_read(bd71837->regmap, reg, &val);
+ if (r < 0)
+ return r;
+ return val;
+}
+
+static inline int bd71837_reg_write(struct bd71837 *bd71837, u8 reg,
+ unsigned int val)
+{
+ return regmap_write(bd71837->regmap, reg, val);
+}
+
+static inline int bd71837_set_bits(struct bd71837 *bd71837, u8 reg, u8 mask)
+{
+ return regmap_update_bits(bd71837->regmap, reg, mask, mask);
+}
+
+static inline int bd71837_clear_bits(struct bd71837 *bd71837, u8 reg,
+ u8 mask)
+{
+ return regmap_update_bits(bd71837->regmap, reg, mask, 0);
+}
+
+static inline int bd71837_update_bits(struct bd71837 *bd71837, u8 reg,
+ u8 mask, u8 val)
+{
+ return regmap_update_bits(bd71837->regmap, reg, mask, val);
+}
+
+#endif /* __LINUX_MFD_BD71837_H__ */
--
2.14.3
next prev parent reply other threads:[~2018-06-19 10:56 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-19 10:55 [PATCH v7 0/4] mfd/regulator/clk/input: bd71837: ROHM BD71837 PMIC driver Matti Vaittinen
2018-06-19 10:55 ` Matti Vaittinen [this message]
2018-06-26 9:06 ` [PATCH v7 1/4] mfd: bd71837: mfd driver for ROHM BD71837 PMIC Enric Balletbo Serra
2018-06-26 11:24 ` Matti Vaittinen
2018-06-26 11:40 ` Enric Balletbo Serra
2018-06-26 12:03 ` Matti Vaittinen
2018-06-26 14:24 ` Enric Balletbo Serra
2018-07-03 6:56 ` Lee Jones
2018-07-03 8:09 ` Enric Balletbo Serra
2018-07-03 6:53 ` Lee Jones
2018-07-04 14:56 ` Dmitry Torokhov
2018-07-04 16:57 ` Enric Balletbo Serra
2018-07-05 5:52 ` Lee Jones
2018-07-05 7:56 ` Matti Vaittinen
2018-07-06 6:38 ` Dmitry Torokhov
2018-07-06 7:05 ` Lee Jones
2018-07-06 7:49 ` Matti Vaittinen
2018-06-19 10:56 ` [PATCH v7 2/4] mfd: bd71837: Devicetree bindings " Matti Vaittinen
2018-06-19 10:56 ` [PATCH v7 3/4] clk: bd71837: Add driver for BD71837 PMIC clock Matti Vaittinen
2018-06-19 10:57 ` [PATCH v7 4/4] input/power: Add driver for BD71837/BD71847 PMIC power button Matti Vaittinen
2018-06-19 17:50 ` Dmitry Torokhov
2018-06-20 6:43 ` Matti Vaittinen
2018-06-21 10:25 ` Matti Vaittinen
2018-06-27 0:21 ` Dmitry Torokhov
2018-06-21 10:34 ` [PATCH v7 0/4] mfd/regulator/clk/input: bd71837: ROHM BD71837 PMIC driver Matti Vaittinen
2018-07-03 7:02 ` Lee Jones
2018-07-04 8:47 ` Matti Vaittinen
2018-07-04 9:21 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7e1888375c979accc402e9ddd7316e528b2ac52c.1529404894.git.matti.vaittinen@fi.rohmeurope.com \
--to=matti.vaittinen@fi.rohmeurope.com \
--cc=andrew.smirnov@gmail.com \
--cc=arnd@arndb.de \
--cc=broonie@kernel.org \
--cc=chenjh@rock-chips.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=heikki.haikola@fi.rohmeurope.com \
--cc=heiko@sntech.de \
--cc=kstewart@linuxfoundation.org \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mazziesaccount@gmail.com \
--cc=mikko.mutanen@fi.rohmeurope.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=sre@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).