From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
To: Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
Masami Hiramatsu <masami.hiramatsu@linaro.org>,
Jassi Brar <jaswinder.singh@linaro.org>,
Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Subject: [PATCH v3 2/2] regulator: uniphier: add regulator driver for UniPhier SoC
Date: Wed, 11 Jul 2018 13:30:52 +0900 [thread overview]
Message-ID: <1531283452-9705-3-git-send-email-hayashi.kunihiko@socionext.com> (raw)
In-Reply-To: <1531283452-9705-1-git-send-email-hayashi.kunihiko@socionext.com>
Initial commit to add support for regulators implemented in UniPhier SoCs.
This supports USB VBUS only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
drivers/regulator/Kconfig | 8 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/uniphier-regulator.c | 213 +++++++++++++++++++++++++++++++++
3 files changed, 222 insertions(+)
create mode 100644 drivers/regulator/uniphier-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 097f617..7f7ad0d 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -932,6 +932,14 @@ config REGULATOR_TWL4030
This driver supports the voltage regulators provided by
this family of companion chips.
+config REGULATOR_UNIPHIER
+ tristate "UniPhier regulator driver"
+ depends on ARCH_UNIPHIER || COMPILE_TEST
+ depends on OF && MFD_SYSCON
+ default ARCH_UNIPHIER
+ help
+ Support for regulators implemented on Socionext UniPhier SoCs.
+
config REGULATOR_VCTRL
tristate "Voltage controlled regulators"
depends on OF
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 590674f..c0dd281 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -116,6 +116,7 @@ obj-$(CONFIG_REGULATOR_TPS65912) += tps65912-regulator.o
obj-$(CONFIG_REGULATOR_TPS80031) += tps80031-regulator.o
obj-$(CONFIG_REGULATOR_TPS65132) += tps65132-regulator.o
obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o twl6030-regulator.o
+obj-$(CONFIG_REGULATOR_UNIPHIER) += uniphier-regulator.o
obj-$(CONFIG_REGULATOR_VCTRL) += vctrl-regulator.o
obj-$(CONFIG_REGULATOR_VEXPRESS) += vexpress-regulator.o
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
diff --git a/drivers/regulator/uniphier-regulator.c b/drivers/regulator/uniphier-regulator.c
new file mode 100644
index 0000000..abf22ac
--- /dev/null
+++ b/drivers/regulator/uniphier-regulator.c
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Regulator controller driver for UniPhier SoC
+// Copyright 2018 Socionext Inc.
+// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/reset.h>
+
+#define MAX_CLKS 2
+#define MAX_RSTS 2
+
+struct uniphier_regulator_soc_data {
+ int nclks;
+ const char * const *clock_names;
+ int nrsts;
+ const char * const *reset_names;
+ const struct regulator_desc *desc;
+ const struct regmap_config *regconf;
+};
+
+struct uniphier_regulator_priv {
+ struct clk_bulk_data clk[MAX_CLKS];
+ struct reset_control *rst[MAX_RSTS];
+ const struct uniphier_regulator_soc_data *data;
+};
+
+static struct regulator_ops uniphier_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+};
+
+static int uniphier_regulator_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct uniphier_regulator_priv *priv;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct regmap *regmap;
+ struct resource *res;
+ void __iomem *base;
+ const char *name;
+ int i, ret, nr;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->data = of_device_get_match_data(dev);
+ if (WARN_ON(!priv->data))
+ return -EINVAL;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ for (i = 0; i < priv->data->nclks; i++)
+ priv->clk[i].id = priv->data->clock_names[i];
+ ret = devm_clk_bulk_get(dev, priv->data->nclks, priv->clk);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < priv->data->nrsts; i++) {
+ name = priv->data->reset_names[i];
+ priv->rst[i] = devm_reset_control_get_shared(dev, name);
+ if (IS_ERR(priv->rst[i]))
+ return PTR_ERR(priv->rst[i]);
+ }
+
+ ret = clk_bulk_prepare_enable(priv->data->nclks, priv->clk);
+ if (ret)
+ return ret;
+
+ for (nr = 0; nr < priv->data->nrsts; nr++) {
+ ret = reset_control_deassert(priv->rst[nr]);
+ if (ret)
+ goto out_rst_assert;
+ }
+
+ regmap = devm_regmap_init_mmio(dev, base, priv->data->regconf);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ config.dev = dev;
+ config.driver_data = priv;
+ config.of_node = dev->of_node;
+ config.regmap = regmap;
+ config.init_data = of_get_regulator_init_data(dev, dev->of_node,
+ priv->data->desc);
+ rdev = devm_regulator_register(dev, priv->data->desc, &config);
+ if (IS_ERR(rdev)) {
+ ret = PTR_ERR(rdev);
+ goto out_rst_assert;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+out_rst_assert:
+ while (nr--)
+ reset_control_assert(priv->rst[nr]);
+
+ clk_bulk_disable_unprepare(priv->data->nclks, priv->clk);
+
+ return ret;
+}
+
+static int uniphier_regulator_remove(struct platform_device *pdev)
+{
+ struct uniphier_regulator_priv *priv = platform_get_drvdata(pdev);
+ int i;
+
+ for (i = 0; i < priv->data->nrsts; i++)
+ reset_control_assert(priv->rst[i]);
+
+ clk_bulk_disable_unprepare(priv->data->nclks, priv->clk);
+
+ return 0;
+}
+
+/* USB3 controller data */
+#define USB3VBUS_OFFSET 0x0
+#define USB3VBUS_REG BIT(4)
+#define USB3VBUS_REG_EN BIT(3)
+static const struct regulator_desc uniphier_usb3_regulator_desc = {
+ .name = "vbus",
+ .of_match = of_match_ptr("vbus"),
+ .ops = &uniphier_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .enable_reg = USB3VBUS_OFFSET,
+ .enable_mask = USB3VBUS_REG_EN | USB3VBUS_REG,
+ .enable_val = USB3VBUS_REG_EN | USB3VBUS_REG,
+ .disable_val = USB3VBUS_REG_EN,
+};
+
+static const struct regmap_config uniphier_usb3_regulator_regconf = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = 1,
+};
+
+static const char * const uniphier_pro4_clock_reset_names[] = {
+ "gio", "link",
+};
+
+static const struct uniphier_regulator_soc_data uniphier_pro4_usb3_data = {
+ .nclks = ARRAY_SIZE(uniphier_pro4_clock_reset_names),
+ .clock_names = uniphier_pro4_clock_reset_names,
+ .nrsts = ARRAY_SIZE(uniphier_pro4_clock_reset_names),
+ .reset_names = uniphier_pro4_clock_reset_names,
+ .desc = &uniphier_usb3_regulator_desc,
+ .regconf = &uniphier_usb3_regulator_regconf,
+};
+
+static const char * const uniphier_pxs2_clock_reset_names[] = {
+ "link",
+};
+
+static const struct uniphier_regulator_soc_data uniphier_pxs2_usb3_data = {
+ .nclks = ARRAY_SIZE(uniphier_pxs2_clock_reset_names),
+ .clock_names = uniphier_pxs2_clock_reset_names,
+ .nrsts = ARRAY_SIZE(uniphier_pxs2_clock_reset_names),
+ .reset_names = uniphier_pxs2_clock_reset_names,
+ .desc = &uniphier_usb3_regulator_desc,
+ .regconf = &uniphier_usb3_regulator_regconf,
+};
+
+static const struct of_device_id uniphier_regulator_match[] = {
+ /* USB VBUS */
+ {
+ .compatible = "socionext,uniphier-pro4-usb3-regulator",
+ .data = &uniphier_pro4_usb3_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs2-usb3-regulator",
+ .data = &uniphier_pxs2_usb3_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld20-usb3-regulator",
+ .data = &uniphier_pxs2_usb3_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs3-usb3-regulator",
+ .data = &uniphier_pxs2_usb3_data,
+ },
+ { /* Sentinel */ },
+};
+
+static struct platform_driver uniphier_regulator_driver = {
+ .probe = uniphier_regulator_probe,
+ .remove = uniphier_regulator_remove,
+ .driver = {
+ .name = "uniphier-regulator",
+ .of_match_table = uniphier_regulator_match,
+ },
+};
+module_platform_driver(uniphier_regulator_driver);
+
+MODULE_AUTHOR("Kunihiko Hayashi <hayashi.kunihiko@socionext.com>");
+MODULE_DESCRIPTION("UniPhier Regulator Controller Driver");
+MODULE_LICENSE("GPL");
--
2.7.4
next prev parent reply other threads:[~2018-07-11 4:31 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-11 4:30 [PATCH v3 0/2] regulator: add new UniPhier regulator support Kunihiko Hayashi
2018-07-11 4:30 ` [PATCH v3 1/2] dt-bindings: regulator: add DT bindings for UniPhier regulator Kunihiko Hayashi
2018-07-11 4:30 ` Kunihiko Hayashi [this message]
2018-07-11 9:33 ` Applied "regulator: uniphier: add regulator driver for UniPhier SoC" to the regulator tree Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1531283452-9705-3-git-send-email-hayashi.kunihiko@socionext.com \
--to=hayashi.kunihiko@socionext.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jaswinder.singh@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=masami.hiramatsu@linaro.org \
--cc=robh+dt@kernel.org \
--cc=yamada.masahiro@socionext.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).