From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: xuwei5@hisilicon.com, robh+dt@kernel.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, amit.kucheria@linaro.org,
guodong.xu@linaro.org,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: [PATCH 2/4] arm64: dts: Add devicetree for Hisilicon Hi3670 SoC
Date: Fri, 10 Aug 2018 23:23:37 +0530 [thread overview]
Message-ID: <20180810175339.25421-3-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20180810175339.25421-1-manivannan.sadhasivam@linaro.org>
Add initial devicetree support for Hisilicon Hi3670 SoC which
is similar to Hi3660 SoC with NPU support.
This SoC has Octal core BigLittle CPUs in two clusters(4 * A53 & 4 * A73).
Only UART6 has been added for console support which is
pre configured by the bootloader. A fixed clock is sourcing
the UART6 which will get replaced by the clock driver when available.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 162 ++++++++++++++++++++++
1 file changed, 162 insertions(+)
create mode 100644 arch/arm64/boot/dts/hisilicon/hi3670.dtsi
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
new file mode 100644
index 000000000000..c90e6f6a34ec
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Hisilicon Hi3670 SoC
+ *
+ * Copyright (C) 2016, Hisilicon Ltd.
+ * Copyright (C) 2018, Linaro Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "hisilicon,hi3670";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ cluster1 {
+ core0 {
+ cpu = <&cpu4>;
+ };
+ core1 {
+ cpu = <&cpu5>;
+ };
+ core2 {
+ cpu = <&cpu6>;
+ };
+ core3 {
+ cpu = <&cpu7>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+
+ cpu4: cpu@100 {
+ compatible = "arm,cortex-a73", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ };
+
+ cpu5: cpu@101 {
+ compatible = "arm,cortex-a73", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ };
+
+ cpu6: cpu@102 {
+ compatible = "arm,cortex-a73", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x102>;
+ enable-method = "psci";
+ };
+
+ cpu7: cpu@103 {
+ compatible = "arm,cortex-a73", "arm,armv8";
+ device_type = "cpu";
+ reg = <0x0 0x103>;
+ enable-method = "psci";
+ };
+ };
+
+ gic: interrupt-controller@e82b0000 {
+ compatible = "arm,gic-400";
+ reg = <0x0 0xe82b1000 0 0x1000>, /* GICD */
+ <0x0 0xe82b2000 0 0x2000>, /* GICC */
+ <0x0 0xe82b4000 0 0x2000>, /* GICH */
+ <0x0 0xe82b6000 0 0x2000>; /* GICV */
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <1920000>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ uart6_clk: clk_19_2M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <19200000>;
+ };
+
+ uart6: serial@fff32000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfff32000 0x0 0x1000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart6_clk &uart6_clk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+ };
+};
--
2.17.1
next prev parent reply other threads:[~2018-08-10 17:54 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-10 17:53 [PATCH 0/4] Add HiSilicon Hi3670 SoC and HiKey970 board Manivannan Sadhasivam
2018-08-10 17:53 ` [PATCH 1/4] dt-bindings: arm: hisilicon: Add binding for Hi3670 SoC Manivannan Sadhasivam
2018-08-14 20:53 ` Rob Herring
2018-08-10 17:53 ` Manivannan Sadhasivam [this message]
2018-08-10 17:53 ` [PATCH 3/4] dt-bindings: arm: hisilicon: Add binding for HiKey970 board Manivannan Sadhasivam
2018-08-14 20:54 ` Rob Herring
2018-08-10 17:53 ` [PATCH 4/4] arm64: dts: Add devicetree support " Manivannan Sadhasivam
2018-08-30 3:14 ` [PATCH 0/4] Add HiSilicon Hi3670 SoC and " Manivannan Sadhasivam
2018-09-19 15:32 ` Wei Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180810175339.25421-3-manivannan.sadhasivam@linaro.org \
--to=manivannan.sadhasivam@linaro.org \
--cc=amit.kucheria@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=guodong.xu@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=xuwei5@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).