From: Salil Mehta <salil.mehta@huawei.com>
To: <davem@davemloft.net>
Cc: <salil.mehta@huawei.com>, <yisen.zhuang@huawei.com>,
<lipeng321@huawei.com>, <mehta.salil.lnk@gmail.com>,
<netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linuxarm@huawei.com>, Yunsheng Lin <linyunsheng@huawei.com>
Subject: [PATCH net-next 1/9] net: hns3: Add support for serdes loopback selftest
Date: Sun, 12 Aug 2018 10:47:30 +0100 [thread overview]
Message-ID: <20180812094738.14852-2-salil.mehta@huawei.com> (raw)
In-Reply-To: <20180812094738.14852-1-salil.mehta@huawei.com>
From: Peng Li <lipeng321@huawei.com>
This patch adds support for serdes loopback selftest in hns3
driver.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
---
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 7 ++-
.../net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h | 12 +++++
.../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 57 +++++++++++++++++++++-
3 files changed, 73 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
index 80ba95d76260..f4710e498c59 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
@@ -53,7 +53,7 @@ static const struct hns3_stats hns3_rxq_stats[] = {
#define HNS3_TQP_STATS_COUNT (HNS3_TXQ_STATS_COUNT + HNS3_RXQ_STATS_COUNT)
-#define HNS3_SELF_TEST_TPYE_NUM 1
+#define HNS3_SELF_TEST_TPYE_NUM 2
#define HNS3_NIC_LB_TEST_PKT_NUM 1
#define HNS3_NIC_LB_TEST_RING_ID 0
#define HNS3_NIC_LB_TEST_PACKET_SIZE 128
@@ -78,6 +78,7 @@ static int hns3_lp_setup(struct net_device *ndev, enum hnae3_loop loop, bool en)
return -EOPNOTSUPP;
switch (loop) {
+ case HNAE3_MAC_INTER_LOOP_SERDES:
case HNAE3_MAC_INTER_LOOP_MAC:
ret = h->ae_algo->ops->set_loopback(h, loop, en);
break;
@@ -303,6 +304,10 @@ static void hns3_self_test(struct net_device *ndev,
st_param[HNAE3_MAC_INTER_LOOP_MAC][1] =
h->flags & HNAE3_SUPPORT_MAC_LOOPBACK;
+ st_param[HNAE3_MAC_INTER_LOOP_SERDES][0] = HNAE3_MAC_INTER_LOOP_SERDES;
+ st_param[HNAE3_MAC_INTER_LOOP_SERDES][1] =
+ h->flags & HNAE3_SUPPORT_SERDES_LOOPBACK;
+
if (if_running)
dev_close(ndev);
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
index cd0a4f228470..821d4c2f84bd 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
@@ -94,6 +94,7 @@ enum hclge_opcode_type {
HCLGE_OPC_QUERY_LINK_STATUS = 0x0307,
HCLGE_OPC_CONFIG_MAX_FRM_SIZE = 0x0308,
HCLGE_OPC_CONFIG_SPEED_DUP = 0x0309,
+ HCLGE_OPC_SERDES_LOOPBACK = 0x0315,
/* PFC/Pause commands */
HCLGE_OPC_CFG_MAC_PAUSE_EN = 0x0701,
@@ -775,6 +776,17 @@ struct hclge_reset_cmd {
u8 fun_reset_vfid;
u8 rsv[22];
};
+
+#define HCLGE_CMD_SERDES_SERIAL_INNER_LOOP_B BIT(0)
+#define HCLGE_CMD_SERDES_DONE_B BIT(0)
+#define HCLGE_CMD_SERDES_SUCCESS_B BIT(1)
+struct hclge_serdes_lb_cmd {
+ u8 mask;
+ u8 enable;
+ u8 result;
+ u8 rsv[21];
+};
+
#define HCLGE_DEFAULT_TX_BUF 0x4000 /* 16k bytes */
#define HCLGE_TOTAL_PKT_BUF 0x108000 /* 1.03125M bytes */
#define HCLGE_DEFAULT_DV 0xA000 /* 40k byte */
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index fc813b7f20e8..99dda5051f5f 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -787,9 +787,10 @@ static int hclge_get_sset_count(struct hnae3_handle *handle, int stringset)
hdev->hw.mac.speed == HCLGE_MAC_SPEED_1G) {
count += 1;
handle->flags |= HNAE3_SUPPORT_MAC_LOOPBACK;
- } else {
- count = -EOPNOTSUPP;
}
+
+ count ++;
+ handle->flags |= HNAE3_SUPPORT_SERDES_LOOPBACK;
} else if (stringset == ETH_SS_STATS) {
count = ARRAY_SIZE(g_mac_stats_string) +
ARRAY_SIZE(g_all_32bit_stats_string) +
@@ -3670,6 +3671,55 @@ static int hclge_set_mac_loopback(struct hclge_dev *hdev, bool en)
return ret;
}
+static int hclge_set_serdes_loopback(struct hclge_dev *hdev, bool en)
+{
+#define HCLGE_SERDES_RETRY_MS 10
+#define HCLGE_SERDES_RETRY_NUM 100
+ struct hclge_serdes_lb_cmd *req;
+ struct hclge_desc desc;
+ int ret, i = 0;
+
+ req = (struct hclge_serdes_lb_cmd *)&desc.data[0];
+ hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_SERDES_LOOPBACK, false);
+
+ if (en) {
+ req->enable = HCLGE_CMD_SERDES_SERIAL_INNER_LOOP_B;
+ req->mask = HCLGE_CMD_SERDES_SERIAL_INNER_LOOP_B;
+ } else {
+ req->mask = HCLGE_CMD_SERDES_SERIAL_INNER_LOOP_B;
+ }
+
+ ret = hclge_cmd_send(&hdev->hw, &desc, 1);
+ if (ret) {
+ dev_err(&hdev->pdev->dev,
+ "serdes loopback set fail, ret = %d\n", ret);
+ return ret;
+ }
+
+ do {
+ msleep(HCLGE_SERDES_RETRY_MS);
+ hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_SERDES_LOOPBACK,
+ true);
+ ret = hclge_cmd_send(&hdev->hw, &desc, 1);
+ if (ret) {
+ dev_err(&hdev->pdev->dev,
+ "serdes loopback get, ret = %d\n", ret);
+ return ret;
+ }
+ } while (++i < HCLGE_SERDES_RETRY_NUM &&
+ !(req->result & HCLGE_CMD_SERDES_DONE_B));
+
+ if (!(req->result & HCLGE_CMD_SERDES_DONE_B)) {
+ dev_err(&hdev->pdev->dev, "serdes loopback set timeout\n");
+ return -EBUSY;
+ } else if (!(req->result & HCLGE_CMD_SERDES_SUCCESS_B)) {
+ dev_err(&hdev->pdev->dev, "serdes loopback set failed in fw\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
static int hclge_set_loopback(struct hnae3_handle *handle,
enum hnae3_loop loop_mode, bool en)
{
@@ -3681,6 +3731,9 @@ static int hclge_set_loopback(struct hnae3_handle *handle,
case HNAE3_MAC_INTER_LOOP_MAC:
ret = hclge_set_mac_loopback(hdev, en);
break;
+ case HNAE3_MAC_INTER_LOOP_SERDES:
+ ret = hclge_set_serdes_loopback(hdev, en);
+ break;
default:
ret = -ENOTSUPP;
dev_err(&hdev->pdev->dev,
--
2.11.0
next prev parent reply other threads:[~2018-08-12 9:48 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-12 9:47 [PATCH net-next 0/9] Misc bug fixes & small enhancements for HNS3 Driver Salil Mehta
2018-08-12 9:47 ` Salil Mehta [this message]
2018-08-13 15:54 ` [PATCH net-next 1/9] net: hns3: Add support for serdes loopback selftest David Miller
2018-08-14 16:17 ` Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 2/9] net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 3/9] net: hns3: Fix for information of phydev lost problem when down/up Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 4/9] net: hns3: Fix for phy link issue when using marvell phy driver Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 5/9] net: hns3: Fix for vf vlan delete failed problem Salil Mehta
2018-08-13 15:56 ` David Miller
2018-08-14 16:35 ` Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 6/9] net: hns3: Fix desc num set to default when setting channel Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 7/9] net: hns3: Remove tx ring BD len register in hns3_enet Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 8/9] net: hns3: Set tx ring' tc info when netdev is up Salil Mehta
2018-08-12 9:47 ` [PATCH net-next 9/9] net: hns3: Add vlan filter setting by ethtool command -K Salil Mehta
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180812094738.14852-2-salil.mehta@huawei.com \
--to=salil.mehta@huawei.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxarm@huawei.com \
--cc=linyunsheng@huawei.com \
--cc=lipeng321@huawei.com \
--cc=mehta.salil.lnk@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=yisen.zhuang@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).