From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: lee.jones@linaro.org, robh+dt@kernel.org, mark.rutland@arm.com,
lgirdwood@gmail.com, broonie@kernel.org,
mazziesaccount@gmail.com, matti.vaittinen@fi.rohmeurope.com,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
heikki.haikola@fi.rohmeurope.com,
mikko.mutanen@fi.rohmeurope.com
Subject: [PATCH 4/8] mfd: dt bindings: add BD71847 device-tree binding documentation
Date: Wed, 29 Aug 2018 15:37:55 +0300 [thread overview]
Message-ID: <09eceb20f4f05ac48c6767d5f3359743e5b98985.1535545377.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1535545377.git.matti.vaittinen@fi.rohmeurope.com>
Add ROHM BD71847 Power Management IC MFD binding information to
device-tree binding documents.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
.../devicetree/bindings/mfd/rohm,bd71837-pmic.txt | 17 +++++++++--------
1 file changed, 9 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
index 3ca56fdb5ffe..d78172878faa 100644
--- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
@@ -1,16 +1,17 @@
-* ROHM BD71837 Power Management Integrated Circuit bindings
+* ROHM BD71837 and BD71847 Power Management Integrated Circuit bindings
-BD71837MWV is a programmable Power Management IC for powering single-core,
-dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for
-low BOM cost and compact solution footprint. It integrates 8 Buck
-egulators and 7 LDOs to provide all the power rails required by the SoC and
-the commonly used peripherals.
+BD71837MWV and BD71847MWV are programmable Power Management ICs for powering
+single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. They are
+optimized for low BOM cost and compact solution footprint. BD71837MWV
+integrates 8 Buck regulators and 7 LDOs. BD71847MWV contains 6 Buck regulators
+and 6 LDOs.
-Datasheet for PMIC is available at:
+Datasheet for BD71837 is available at:
https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e
Required properties:
- - compatible : Should be "rohm,bd71837".
+ - compatible : Should be "rohm,bd71837" for bd71837 and
+ "rohm,bd71847" for bd71847.
- reg : I2C slave address.
- interrupt-parent : Phandle to the parent interrupt controller.
- interrupts : The interrupt line the device is connected to.
--
2.14.3
next prev parent reply other threads:[~2018-08-29 12:38 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-29 12:35 [PATCH 0/8] regulator/mfd/dt_bindings: bd718x7: Support ROHM bd71847 Matti Vaittinen
2018-08-29 12:36 ` [PATCH 1/8] regulator: bd71837: Disable voltage monitoring for LDO3/4 Matti Vaittinen
2018-09-11 12:40 ` Lee Jones
2018-09-12 7:47 ` Matti Vaittinen
2018-09-12 8:42 ` Lee Jones
2018-09-12 8:53 ` Matti Vaittinen
2018-09-12 10:23 ` Mark Brown
2018-09-12 10:44 ` Lee Jones
2018-08-29 12:36 ` [PATCH 2/8] regulator: Support ROHM BD71847 power management IC Matti Vaittinen
2018-09-11 13:48 ` Lee Jones
2018-09-12 6:37 ` Matti Vaittinen
2018-08-29 12:37 ` [PATCH 3/8] regulator: dt bindings: add BD71847 device-tree binding documentation Matti Vaittinen
2018-08-29 12:37 ` Matti Vaittinen [this message]
2018-09-11 13:49 ` [PATCH 4/8] mfd: " Lee Jones
2018-09-12 7:43 ` Matti Vaittinen
2018-08-29 12:38 ` [PATCH 5/8] regulator: Support regulators where voltage ranges are selectable Matti Vaittinen
2018-08-29 12:38 ` [PATCH 6/8] regulator/mfd: bd718xx: rename bd71837/bd71847 common instances Matti Vaittinen
2018-09-11 13:51 ` Lee Jones
2018-08-29 12:39 ` [PATCH 7/8] regulator: bd718XX use pickable ranges Matti Vaittinen
2018-09-11 13:55 ` Lee Jones
2018-09-12 7:41 ` Matti Vaittinen
2018-08-29 12:39 ` [PATCH 8/8] regulator: bd718xx: renme bd71837 to 718xx Matti Vaittinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=09eceb20f4f05ac48c6767d5f3359743e5b98985.1535545377.git.matti.vaittinen@fi.rohmeurope.com \
--to=matti.vaittinen@fi.rohmeurope.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=heikki.haikola@fi.rohmeurope.com \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mazziesaccount@gmail.com \
--cc=mikko.mutanen@fi.rohmeurope.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).