From: Aapo Vienamo <avienamo@nvidia.com>
To: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Thierry Reding <thierry.reding@gmail.com>,
Jonathan Hunter <jonathanh@nvidia.com>,
Ulf Hansson <ulf.hansson@linaro.org>,
Adrian Hunter <adrian.hunter@intel.com>,
Mikko Perttunen <mperttunen@nvidia.com>,
"Stefan Agner" <stefan@agner.ch>
Cc: <devicetree@vger.kernel.org>, <linux-tegra@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
Aapo Vienamo <avienamo@nvidia.com>
Subject: [PATCH v3 24/38] mmc: tegra: Remove tegra_sdhci_writew() from tegra210_sdhci_ops
Date: Thu, 30 Aug 2018 18:06:25 +0300 [thread overview]
Message-ID: <20180830150639.21048-25-avienamo@nvidia.com> (raw)
In-Reply-To: <20180830150639.21048-1-avienamo@nvidia.com>
tegra_sdhci_writew() defers the write to SDHCI_TRANSFER_MODE until
SDHCI_COMMAND is written. This is not necessary on Tegra210 and Tegra186
and it breaks read-modify-write operations on SDHCI_TRANSFER_MODE
because writes to SDHCI_TRANSFER_MODE aren't visible until SDHCI_COMMAND
has been written to. This results in tuning failures on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
---
drivers/mmc/host/sdhci-tegra.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index f68557a01d5d..0bdce437e752 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -834,7 +834,6 @@ static const struct sdhci_tegra_soc_data soc_data_tegra124 = {
static const struct sdhci_ops tegra210_sdhci_ops = {
.get_ro = tegra_sdhci_get_ro,
.read_w = tegra_sdhci_readw,
- .write_w = tegra_sdhci_writew,
.write_l = tegra_sdhci_writel,
.set_clock = tegra_sdhci_set_clock,
.set_bus_width = sdhci_set_bus_width,
--
2.18.0
next prev parent reply other threads:[~2018-08-30 15:08 UTC|newest]
Thread overview: 45+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-30 15:06 [PATCH v3 00/38] Tegra SDHCI add support for HS200 and UHS signaling Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 01/38] dt-bindings: Add Tegra PMC pad configuration bindings Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 02/38] dt-bindings: mmc: tegra: Add pad voltage control properties Aapo Vienamo
2018-08-31 13:15 ` Ulf Hansson
2018-08-30 15:06 ` [PATCH v3 03/38] dt-bindings: Add Tegra SDHCI pad pdpu offset bindings Aapo Vienamo
2018-08-31 13:15 ` Ulf Hansson
2018-08-30 15:06 ` [PATCH v3 04/38] dt-bindings: mmc: Add Tegra SDHCI sampling trimmer values Aapo Vienamo
2018-08-31 13:15 ` Ulf Hansson
2018-08-30 15:06 ` [PATCH v3 05/38] soc/tegra: pmc: Fix pad voltage configuration for Tegra186 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 06/38] soc/tegra: pmc: Factor out DPD register bit calculation Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 07/38] soc/tegra: pmc: Implement tegra_io_pad_is_powered() Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 08/38] soc/tegra: pmc: Use X macro to generate IO pad tables Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 09/38] soc/tegra: pmc: Remove public pad voltage APIs Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 10/38] soc/tegra: pmc: Implement pad configuration via pinctrl Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 11/38] mmc: tegra: Reconfigure pad voltages during voltage switching Aapo Vienamo
2018-08-31 13:16 ` Ulf Hansson
2018-08-31 13:59 ` Thierry Reding
2018-08-30 15:06 ` [PATCH v3 12/38] mmc: tegra: Poll for calibration completion Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 13/38] mmc: tegra: Set calibration pad voltage reference Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 14/38] mmc: tegra: Power on the calibration pad Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 15/38] mmc: tegra: Disable card clock during pad calibration Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 16/38] mmc: tegra: Program pad autocal offsets from dt Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 17/38] mmc: tegra: Perform pad calibration after voltage switch Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 18/38] mmc: tegra: Enable pad calibration on Tegra210 and Tegra186 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 19/38] mmc: tegra: Add a workaround for tap value change glitch Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 20/38] mmc: tegra: Parse default trim and tap from dt Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 21/38] mmc: tegra: Configure default tap values Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 22/38] mmc: tegra: Configure default trim value on reset Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 23/38] mmc: tegra: Use standard SDHCI tuning on Tegra210 and Tegra186 Aapo Vienamo
2018-08-30 15:06 ` Aapo Vienamo [this message]
2018-08-30 15:06 ` [PATCH v3 25/38] mmc: tegra: Disable card clock during tuning cmd on Tegra210 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 26/38] mmc: tegra: Enable UHS and HS200 modes for Tegra210 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 27/38] mmc: tegra: Enable UHS and HS200 modes for Tegra186 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 28/38] arm64: dts: Add Tegra210 sdmmc pinctrl voltage states Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 29/38] arm64: dts: Add Tegra186 " Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 30/38] arm64: dts: tegra210-p2180: Allow ldo2 to go down to 1.8 V Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 31/38] arm64: dts: tegra210-p2180: Correct sdmmc4 vqmmc-supply Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 32/38] arm64: dts: tegra210-p2597: Remove no-1-8-v from sdmmc1 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 33/38] arm64: dts: tegra186: Add sdmmc pad auto calibration offsets Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 34/38] arm64: dts: tegra210: " Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 35/38] arm64: dts: tegra210: Add SDHCI tap and trim values Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 36/38] arm64: dts: tegra186: " Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 37/38] arm64: dts: tegra186: Assign clocks for sdmmc1 and sdmmc4 Aapo Vienamo
2018-08-30 15:06 ` [PATCH v3 38/38] arm64: dts: tegra210: " Aapo Vienamo
2018-08-31 7:20 ` [PATCH v3 00/38] Tegra SDHCI add support for HS200 and UHS signaling Adrian Hunter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180830150639.21048-25-avienamo@nvidia.com \
--to=avienamo@nvidia.com \
--cc=adrian.hunter@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mperttunen@nvidia.com \
--cc=robh+dt@kernel.org \
--cc=stefan@agner.ch \
--cc=thierry.reding@gmail.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).