From: Guo Ren <ren_guo@c-sky.com>
To: tglx@linutronix.de, jason@lakedaemon.net, marc.zyngier@arm.com,
robh+dt@kernel.org, mark.rutland@arm.com,
daniel.lezcano@linaro.org, will.deacon@arm.com,
jhogan@kernel.org, paul.burton@mips.com, peterz@infradead.org,
arnd@arndb.de
Cc: linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
Guo Ren <ren_guo@c-sky.com>
Subject: [PATCH V12 1/8] irqchip: add C-SKY SMP interrupt controller
Date: Fri, 12 Oct 2018 20:02:02 +0800 [thread overview]
Message-ID: <053f23f14de91a2d1bf1d29339a6e4a66aca8cdf.1539315341.git.ren_guo@c-sky.com> (raw)
In-Reply-To: <cover.1539315341.git.ren_guo@c-sky.com>
In-Reply-To: <cover.1539315341.git.ren_guo@c-sky.com>
Irq-csky-mpintc is C-SKY smp system interrupt controller and it
could support 16 soft irqs, 16 private irqs, and 992 max common
irqs.
Changelog:
- Remove set_ipi_irq_mapping.
- Convert the cpumask to an interrupt-controller specific representation
in driver's code, and not the SMP code's.
- pass checkpatch.pl
- Move IPI_IRQ into the driver
- Remove irq_set_default_host() and use set_ipi_irq_mapping()
- Change name with upstream feed-back
- Change irq map, reserve soft_irq & private_irq space
- Add License and Copyright
- Support set_affinity for irq balance in SMP
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
---
drivers/irqchip/Kconfig | 9 ++
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-csky-mpintc.c | 198 ++++++++++++++++++++++++++++++++++++++
3 files changed, 208 insertions(+)
create mode 100644 drivers/irqchip/irq-csky-mpintc.c
diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index 383e7b7..8103f6f 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -371,6 +371,15 @@ config QCOM_PDC
Power Domain Controller driver to manage and configure wakeup
IRQs for Qualcomm Technologies Inc (QTI) mobile chips.
+config CSKY_MPINTC
+ bool "C-SKY Multi Processor Interrupt Controller"
+ depends on CSKY
+ help
+ Say yes here to enable C-SKY SMP interrupt controller driver used
+ for C-SKY SMP system.
+ In fact it's not mmio map in hw and it use ld/st to visit the
+ controller's register inside CPU.
+
endmenu
config SIFIVE_PLIC
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index fbd1ec8..6b739ea 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -87,4 +87,5 @@ obj-$(CONFIG_MESON_IRQ_GPIO) += irq-meson-gpio.o
obj-$(CONFIG_GOLDFISH_PIC) += irq-goldfish-pic.o
obj-$(CONFIG_NDS32) += irq-ativic32.o
obj-$(CONFIG_QCOM_PDC) += qcom-pdc.o
+obj-$(CONFIG_CSKY_MPINTC) += irq-csky-mpintc.o
obj-$(CONFIG_SIFIVE_PLIC) += irq-sifive-plic.o
diff --git a/drivers/irqchip/irq-csky-mpintc.c b/drivers/irqchip/irq-csky-mpintc.c
new file mode 100644
index 0000000..c67c961
--- /dev/null
+++ b/drivers/irqchip/irq-csky-mpintc.c
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd.
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/module.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/smp.h>
+#include <linux/io.h>
+#include <asm/irq.h>
+#include <asm/traps.h>
+#include <asm/reg_ops.h>
+
+static struct irq_domain *root_domain;
+static void __iomem *INTCG_base;
+static void __iomem *INTCL_base;
+
+#define IPI_IRQ 15
+#define INTC_IRQS 256
+#define COMM_IRQ_BASE 32
+
+#define INTCG_SIZE 0x8000
+#define INTCL_SIZE 0x1000
+
+#define INTCG_ICTLR 0x0
+#define INTCG_CICFGR 0x100
+#define INTCG_CIDSTR 0x1000
+
+#define INTCL_PICTLR 0x0
+#define INTCL_SIGR 0x60
+#define INTCL_HPPIR 0x68
+#define INTCL_RDYIR 0x6c
+#define INTCL_SENR 0xa0
+#define INTCL_CENR 0xa4
+#define INTCL_CACR 0xb4
+
+static DEFINE_PER_CPU(void __iomem *, intcl_reg);
+
+static void csky_mpintc_handler(struct pt_regs *regs)
+{
+ void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+ do {
+ handle_domain_irq(root_domain,
+ readl_relaxed(reg_base + INTCL_RDYIR),
+ regs);
+ } while (readl_relaxed(reg_base + INTCL_HPPIR) & BIT(31));
+}
+
+static void csky_mpintc_enable(struct irq_data *d)
+{
+ void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+ writel_relaxed(d->hwirq, reg_base + INTCL_SENR);
+}
+
+static void csky_mpintc_disable(struct irq_data *d)
+{
+ void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+ writel_relaxed(d->hwirq, reg_base + INTCL_CENR);
+}
+
+static void csky_mpintc_eoi(struct irq_data *d)
+{
+ void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+ writel_relaxed(d->hwirq, reg_base + INTCL_CACR);
+}
+
+#ifdef CONFIG_SMP
+static int csky_irq_set_affinity(struct irq_data *d,
+ const struct cpumask *mask_val,
+ bool force)
+{
+ unsigned int cpu;
+ unsigned int offset = 4 * (d->hwirq - COMM_IRQ_BASE);
+
+ if (!force)
+ cpu = cpumask_any_and(mask_val, cpu_online_mask);
+ else
+ cpu = cpumask_first(mask_val);
+
+ if (cpu >= nr_cpu_ids)
+ return -EINVAL;
+
+ /* Enable interrupt destination */
+ cpu |= BIT(31);
+
+ writel_relaxed(cpu, INTCG_base + INTCG_CIDSTR + offset);
+
+ irq_data_update_effective_affinity(d, cpumask_of(cpu));
+
+ return IRQ_SET_MASK_OK_DONE;
+}
+#endif
+
+static struct irq_chip csky_irq_chip = {
+ .name = "C-SKY SMP Intc",
+ .irq_eoi = csky_mpintc_eoi,
+ .irq_enable = csky_mpintc_enable,
+ .irq_disable = csky_mpintc_disable,
+#ifdef CONFIG_SMP
+ .irq_set_affinity = csky_irq_set_affinity,
+#endif
+};
+
+static int csky_irqdomain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ if (hwirq < COMM_IRQ_BASE) {
+ irq_set_percpu_devid(irq);
+ irq_set_chip_and_handler(irq, &csky_irq_chip,
+ handle_percpu_irq);
+ } else {
+ irq_set_chip_and_handler(irq, &csky_irq_chip,
+ handle_fasteoi_irq);
+ }
+
+ return 0;
+}
+
+static const struct irq_domain_ops csky_irqdomain_ops = {
+ .map = csky_irqdomain_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+#ifdef CONFIG_SMP
+static void csky_mpintc_send_ipi(const struct cpumask *mask)
+{
+ void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+ /*
+ * INTCL_SIGR[3:0] INTID
+ * INTCL_SIGR[8:15] CPUMASK
+ */
+ writel_relaxed((*cpumask_bits(mask)) << 8 | IPI_IRQ,
+ reg_base + INTCL_SIGR);
+}
+#endif
+
+/* C-SKY multi processor interrupt controller */
+static int __init
+csky_mpintc_init(struct device_node *node, struct device_node *parent)
+{
+ int ret;
+ unsigned int cpu, nr_irq;
+#ifdef CONFIG_SMP
+ unsigned int ipi_irq;
+#endif
+
+ if (parent)
+ return 0;
+
+ ret = of_property_read_u32(node, "csky,num-irqs", &nr_irq);
+ if (ret < 0)
+ nr_irq = INTC_IRQS;
+
+ if (INTCG_base == NULL) {
+ INTCG_base = ioremap(mfcr("cr<31, 14>"),
+ INTCL_SIZE*nr_cpu_ids + INTCG_SIZE);
+ if (INTCG_base == NULL)
+ return -EIO;
+
+ INTCL_base = INTCG_base + INTCG_SIZE;
+
+ writel_relaxed(BIT(0), INTCG_base + INTCG_ICTLR);
+ }
+
+ root_domain = irq_domain_add_linear(node, nr_irq, &csky_irqdomain_ops,
+ NULL);
+ if (!root_domain)
+ return -ENXIO;
+
+ /* for every cpu */
+ for_each_present_cpu(cpu) {
+ per_cpu(intcl_reg, cpu) = INTCL_base + (INTCL_SIZE * cpu);
+ writel_relaxed(BIT(0), per_cpu(intcl_reg, cpu) + INTCL_PICTLR);
+ }
+
+ set_handle_irq(&csky_mpintc_handler);
+
+#ifdef CONFIG_SMP
+ ipi_irq = irq_create_mapping(root_domain, IPI_IRQ);
+ if (!ipi_irq)
+ return -EIO;
+
+ set_send_ipi(&csky_mpintc_send_ipi, ipi_irq);
+#endif
+
+ return 0;
+}
+IRQCHIP_DECLARE(csky_mpintc, "csky,mpintc", csky_mpintc_init);
--
2.7.4
next prev parent reply other threads:[~2018-10-12 12:02 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-12 12:02 [PATCH V12 0/8] C-SKY(csky) Linux Kernel Driver Guo Ren
2018-10-12 12:02 ` Guo Ren [this message]
2018-10-12 12:02 ` [PATCH V12 2/8] dt-bindings: interrupt-controller: C-SKY SMP intc Guo Ren
2018-10-12 12:02 ` [PATCH V12 3/8] irqchip: add C-SKY APB bus interrupt controller Guo Ren
2018-10-12 12:12 ` [PATCH V12 4/8] dt-bindings: interrupt-controller: C-SKY APB intc Guo Ren
2018-10-12 12:12 ` [PATCH V12 5/8] clocksource: add C-SKY SMP timer Guo Ren
2018-10-12 12:12 ` [PATCH V12 6/8] dt-bindings: timer: C-SKY Multi-processor timer Guo Ren
2018-10-12 12:12 ` [PATCH V12 7/8] clocksource: add gx6605s SOC system timer Guo Ren
2018-10-12 12:12 ` [PATCH V12 8/8] dt-bindings: timer: gx6605s SOC timer Guo Ren
2018-10-13 20:50 ` [PATCH V12 0/8] C-SKY(csky) Linux Kernel Driver Daniel Lezcano
2018-10-14 16:26 ` Guo Ren
2018-10-14 20:38 ` Daniel Lezcano
2018-10-15 2:32 ` Guo Ren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=053f23f14de91a2d1bf1d29339a6e4a66aca8cdf.1539315341.git.ren_guo@c-sky.com \
--to=ren_guo@c-sky.com \
--cc=arnd@arndb.de \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jason@lakedaemon.net \
--cc=jhogan@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marc.zyngier@arm.com \
--cc=mark.rutland@arm.com \
--cc=paul.burton@mips.com \
--cc=peterz@infradead.org \
--cc=robh+dt@kernel.org \
--cc=tglx@linutronix.de \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).