[PATCH v2 1/3] [SPI] [OMAP] Add OMAP spi100k driver

[Cory Maccarrone <darkstar6262@gmail.com>]

This change adds the OMAP SPI 100k driver created by
Fabrice Crohas <fcrohas@gmail.com>.  This SPI bus is found on
OMAP7xx-series smartphones, and for many, the touchscreen is
attached to this bus.

The lion's share of the work was done by Fabrice on this driver --
I am merely porting it from the Linwizard project on his behalf.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
---
 drivers/spi/Kconfig         |    6 +
 drivers/spi/Makefile        |    1 +
 drivers/spi/omap_spi_100k.c |  656 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 663 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/omap_spi_100k.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 4b6f7cb..7ef9b12 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -164,6 +164,12 @@ config SPI_OMAP24XX
 	  SPI master controller for OMAP24xx/OMAP34xx Multichannel SPI
 	  (McSPI) modules.
 
+config SPI_OMAP_100K
+	tristate "OMAP SPI 100K"
+	depends on SPI_MASTER && (ARCH_OMAP850 || ARCH_OMAP730)
+	help
+	  OMAP SPI 100K master controller for omap7xx boards.
+
 config SPI_ORION
 	tristate "Orion SPI master (EXPERIMENTAL)"
 	depends on PLAT_ORION && EXPERIMENTAL
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 21a1182..55f670d 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_SPI_LM70_LLP)		+= spi_lm70llp.o
 obj-$(CONFIG_SPI_PXA2XX)		+= pxa2xx_spi.o
 obj-$(CONFIG_SPI_OMAP_UWIRE)		+= omap_uwire.o
 obj-$(CONFIG_SPI_OMAP24XX)		+= omap2_mcspi.o
+obj-$(CONFIG_SPI_OMAP_100K)		+= omap_spi_100k.o
 obj-$(CONFIG_SPI_ORION)			+= orion_spi.o
 obj-$(CONFIG_SPI_PL022)			+= amba-pl022.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= mpc52xx_psc_spi.o
diff --git a/drivers/spi/omap_spi_100k.c b/drivers/spi/omap_spi_100k.c
new file mode 100644
index 0000000..9fc4897
--- /dev/null
+++ b/drivers/spi/omap_spi_100k.c
@@ -0,0 +1,656 @@
+/*
+ * OMAP7xx SPI 100k controller driver
+ * Author: Fabrice Crohas <fcrohas@gmail.com>
+ * from original omap1_mcspi driver
+ *
+ * Copyright (C) 2005, 2006 Nokia Corporation
+ * Author:      Samuel Ortiz <samuel.ortiz@nokia.com> and
+ *              Juha Yrj�l� <juha.yrjola@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <linux/spi/spi.h>
+
+#include <plat/clock.h>
+
+#define OMAP1_SPI100K_MAX_FREQ          48000000
+
+#define ICR_SPITAS      (OMAP7XX_ICR_BASE + 0x12)
+
+#define SPI_SETUP1      0x00
+#define SPI_SETUP2      0x02
+#define SPI_CTRL        0x04
+#define SPI_STATUS      0x06
+#define SPI_TX_LSB      0x08
+#define SPI_TX_MSB      0x0a
+#define SPI_RX_LSB      0x0c
+#define SPI_RX_MSB      0x0e
+
+#define SPI_SETUP1_INT_READ_ENABLE      (1UL << 5)
+#define SPI_SETUP1_INT_WRITE_ENABLE     (1UL << 4)
+#define SPI_SETUP1_CLOCK_DIVISOR(x)     ((x) << 1)
+#define SPI_SETUP1_CLOCK_ENABLE         (1UL << 0)
+
+#define SPI_SETUP2_ACTIVE_EDGE_FALLING  (0UL << 0)
+#define SPI_SETUP2_ACTIVE_EDGE_RISING   (1UL << 0)
+#define SPI_SETUP2_NEGATIVE_LEVEL       (0UL << 5)
+#define SPI_SETUP2_POSITIVE_LEVEL       (1UL << 5)
+#define SPI_SETUP2_LEVEL_TRIGGER        (0UL << 10)
+#define SPI_SETUP2_EDGE_TRIGGER         (1UL << 10)
+
+#define SPI_CTRL_SEN(x)                 ((x) << 7)
+#define SPI_CTRL_WORD_SIZE(x)           (((x) - 1) << 2)
+#define SPI_CTRL_WR                     (1UL << 1)
+#define SPI_CTRL_RD                     (1UL << 0)
+
+#define SPI_STATUS_WE                   (1UL << 1)
+#define SPI_STATUS_RD                   (1UL << 0)
+
+#define WRITE 0
+#define READ  1
+
+
+/* use PIO for small transfers, avoiding DMA setup/teardown overhead and
+ * cache operations; better heuristics consider wordsize and bitrate.
+ */
+#define DMA_MIN_BYTES                   8
+
+#define SPI_RUNNING	0
+#define SPI_SHUTDOWN	1
+
+struct omap1_spi100k {
+	struct work_struct      work;
+	/* lock protects queue and registers */
+	spinlock_t              lock;
+	struct list_head        msg_queue;
+	struct spi_master       *master;
+	struct clk              *ick;
+	struct clk              *fck;
+	/* Virtual base address of the controller */
+	void __iomem            *base;
+	unsigned long           base_addr;
+	/* State of the SPI */
+	unsigned int		state;
+};
+
+struct omap1_spi100k_cs {
+	void __iomem            *base;
+	int                     word_len;
+};
+
+static struct workqueue_struct *omap1_spi100k_wq;
+
+#define MOD_REG_BIT(val, mask, set) do { \
+	if (set) \
+		val |= mask; \
+	else \
+		val &= ~mask; \
+} while (0)
+
+static void spi100k_enable_clock(struct spi_master *master)
+{
+	unsigned int val;
+	struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
+
+	/* enable SPI */
+	val = omap_readw(spi100k->base_addr + SPI_SETUP1);
+	val |= SPI_SETUP1_CLOCK_ENABLE;
+	omap_writew(val, spi100k->base_addr + SPI_SETUP1);
+}
+
+static void spi100k_disable_clock(struct spi_master *master)
+{
+	unsigned int val;
+	struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
+
+	/* disable SPI */
+	val = omap_readw(spi100k->base_addr + SPI_SETUP1);
+	val &= ~SPI_SETUP1_CLOCK_ENABLE;
+	omap_writew(val, spi100k->base_addr + SPI_SETUP1);
+}
+
+static void spi100k_write_data(struct spi_master *master, int len, int data)
+{
+	struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
+
+	/* write 16-bit word */
+	spi100k_enable_clock(master);
+	omap_writew( data , spi100k->base_addr + SPI_TX_MSB);
+
+	omap_writew(SPI_CTRL_SEN(0) |
+		    SPI_CTRL_WORD_SIZE(len) |
+		    SPI_CTRL_WR,
+		    spi100k->base_addr + SPI_CTRL);
+
+	/* Wait for bit ack send change */
+	while((omap_readw(spi100k->base_addr + SPI_STATUS) & SPI_STATUS_WE) != SPI_STATUS_WE);
+	udelay(1000);
+
+	spi100k_disable_clock(master);
+}
+
+static int spi100k_read_data(struct spi_master *master, int len)
+{
+	int dataH,dataL;
+	struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
+
+	spi100k_enable_clock(master);
+	omap_writew(SPI_CTRL_SEN(0) |
+		    SPI_CTRL_WORD_SIZE(len) |
+		    SPI_CTRL_RD,
+		    spi100k->base_addr + SPI_CTRL);
+
+	while((omap_readw(spi100k->base_addr + SPI_STATUS) & SPI_STATUS_RD) != SPI_STATUS_RD);
+	udelay(1000);
+
+	dataL = omap_readw(spi100k->base_addr + SPI_RX_LSB);
+	dataH = omap_readw(spi100k->base_addr + SPI_RX_MSB);
+	spi100k_disable_clock(master);
+
+	return dataL;
+}
+
+static void spi100k_open(struct spi_master *master)
+{
+	/* get control of SPI */
+	struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
+
+	omap_writew(SPI_SETUP1_INT_READ_ENABLE |
+		    SPI_SETUP1_INT_WRITE_ENABLE |
+		    SPI_SETUP1_CLOCK_DIVISOR(0), spi100k->base_addr + SPI_SETUP1);
+
+	/* configure clock and interrupts */
+	omap_writew(SPI_SETUP2_ACTIVE_EDGE_FALLING |
+		    SPI_SETUP2_NEGATIVE_LEVEL |
+		    SPI_SETUP2_LEVEL_TRIGGER, spi100k->base_addr + SPI_SETUP2);
+
+}
+
+static void omap1_spi100k_force_cs(struct omap1_spi100k *spi100k, int enable)
+{
+	if (enable)
+		omap_writew(0x05fc, spi100k->base_addr + SPI_CTRL);
+	else
+		omap_writew(0x05fd, spi100k->base_addr + SPI_CTRL);
+}
+
+static unsigned
+omap1_spi100k_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
+{
+	struct omap1_spi100k    *spi100k;
+	struct omap1_spi100k_cs *cs = spi->controller_state;
+	unsigned int            count, c;
+	int                     word_len;
+
+	spi100k = spi_master_get_devdata(spi->master);
+	count = xfer->len;
+	c = count;
+	word_len = cs->word_len;
+
+	/* RX_ONLY mode needs dummy data in TX reg */
+	if (xfer->tx_buf == NULL)
+		spi100k_write_data(spi->master,word_len, 0);
+
+	if (word_len <= 8) {
+		u8              *rx;
+		const u8        *tx;
+
+		rx = xfer->rx_buf;
+		tx = xfer->tx_buf;
+		do {
+			c-=1;
+			if (xfer->tx_buf != NULL)
+				spi100k_write_data(spi->master,word_len, *tx);
+			if (xfer->rx_buf != NULL)
+				*rx = spi100k_read_data(spi->master,word_len);
+		} while(c);
+	} else if (word_len <= 16) {
+		u16             *rx;
+		const u16       *tx;
+
+		rx = xfer->rx_buf;
+		tx = xfer->tx_buf;
+		do {
+			c-=2;
+			if (xfer->tx_buf != NULL)
+				spi100k_write_data(spi->master,word_len, *tx++);
+			if (xfer->rx_buf != NULL)
+				*rx++ = spi100k_read_data(spi->master,word_len);
+		} while(c);
+	} else if (word_len <= 32) {
+		u32             *rx;
+		const u32       *tx;
+
+		rx = xfer->rx_buf;
+		tx = xfer->tx_buf;
+		do {
+			c-=4;
+			if (xfer->tx_buf != NULL)
+				spi100k_write_data(spi->master,word_len, *tx);
+			if (xfer->rx_buf != NULL)
+				*rx = spi100k_read_data(spi->master,word_len);
+		} while(c);
+	}
+	return count - c;
+}
+
+/* called only when no transfer is active to this device */
+static int omap1_spi100k_setup_transfer(struct spi_device *spi,
+		struct spi_transfer *t)
+{
+	struct omap1_spi100k *spi100k = spi_master_get_devdata(spi->master);
+	struct omap1_spi100k_cs *cs = spi->controller_state;
+	u8 word_len = spi->bits_per_word;
+
+	if (t != NULL && t->bits_per_word)
+		word_len = t->bits_per_word;
+	if (!word_len)
+		word_len = 8;
+
+	if (spi->bits_per_word > 32)
+		return -EINVAL;
+	cs->word_len = word_len;
+
+	/* SPI init before transfer */
+	omap_writew(0x3e , spi100k->base_addr + SPI_SETUP1);
+	omap_writew(0x00 , spi100k->base_addr + SPI_STATUS);
+	omap_writew(0x3e , spi100k->base_addr + SPI_CTRL);
+
+	return 0;
+}
+
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
+
+static int omap1_spi100k_setup(struct spi_device *spi)
+{
+	int                     ret;
+	struct omap1_spi100k    *spi100k;
+	struct omap1_spi100k_cs *cs = spi->controller_state;
+
+	if (spi->bits_per_word < 4 || spi->bits_per_word > 32) {
+		 dev_dbg(&spi->dev, "setup: unsupported %d bit words\n",
+			spi->bits_per_word);
+		 return -EINVAL;
+	}
+
+	spi100k = spi_master_get_devdata(spi->master);
+
+	if (!cs) {
+		cs = kzalloc(sizeof *cs, GFP_KERNEL);
+		if (!cs)
+			return -ENOMEM;
+		cs->base = spi100k->base + spi->chip_select * 0x14;
+		spi->controller_state = cs;
+	}
+
+	spi100k_open(spi->master);
+
+	clk_enable(spi100k->ick);
+	clk_enable(spi100k->fck);
+
+	ret = omap1_spi100k_setup_transfer(spi, NULL);
+
+	clk_disable(spi100k->ick);
+	clk_disable(spi100k->fck);
+
+	return ret;
+}
+
+static void omap1_spi100k_work(struct work_struct *work)
+{
+	struct omap1_spi100k    *spi100k;
+	int status = 0;
+
+	spi100k = container_of(work, struct omap1_spi100k, work);
+	spin_lock_irq(&spi100k->lock);
+
+	clk_enable(spi100k->ick);
+	clk_enable(spi100k->fck);
+
+	/* We only enable one channel at a time -- the one whose message is
+	 * at the head of the queue -- although this controller would gladly
+	 * arbitrate among multiple channels.  This corresponds to "single
+	 * channel" master mode.  As a side effect, we need to manage the
+	 * chipselect with the FORCE bit ... CS != channel enable.
+	 */
+	 while (!list_empty(&spi100k->msg_queue)) {
+		struct spi_message              *m;
+		struct spi_device               *spi;
+		struct spi_transfer             *t = NULL;
+		int                             cs_active = 0;
+		struct omap1_spi100k_cs         *cs;
+		int                             par_override = 0;
+
+		m = container_of(spi100k->msg_queue.next, struct spi_message,
+				 queue);
+
+		list_del_init(&m->queue);
+		spin_unlock_irq(&spi100k->lock);
+
+		spi = m->spi;
+		cs = spi->controller_state;
+
+		list_for_each_entry(t, &m->transfers, transfer_list) {
+			if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
+				status = -EINVAL;
+				break;
+			}
+			if (par_override || t->speed_hz || t->bits_per_word) {
+				par_override = 1;
+				status = omap1_spi100k_setup_transfer(spi, t);
+				if (status < 0)
+					break;
+				if (!t->speed_hz && !t->bits_per_word)
+					par_override = 0;
+			}
+
+			if (!cs_active) {
+				omap1_spi100k_force_cs(spi100k, 1);
+				cs_active = 1;
+			}
+
+			if (t->len) {
+				unsigned count;
+
+				/* RX_ONLY mode needs dummy data in TX reg */
+				if (t->tx_buf == NULL)
+					spi100k_write_data(spi->master, 8, 0);
+
+				count = omap1_spi100k_txrx_pio(spi, t);
+				m->actual_length += count;
+
+				if (count != t->len) {
+					status = -EIO;
+					break;
+				}
+			}
+
+			if (t->delay_usecs)
+				udelay(t->delay_usecs);
+
+			/* ignore the "leave it on after last xfer" hint */
+
+			if (t->cs_change) {
+				omap1_spi100k_force_cs(spi100k, 0);
+				cs_active = 0;
+			}
+		}
+
+		/* Restore defaults if they were overriden */
+		if (par_override) {
+			par_override = 0;
+			status = omap1_spi100k_setup_transfer(spi, NULL);
+		}
+
+		if (cs_active)
+			omap1_spi100k_force_cs(spi100k, 0);
+
+		m->status = status;
+		m->complete(m->context);
+
+		spin_lock_irq(&spi100k->lock);
+	}
+
+	clk_disable(spi100k->ick);
+	clk_disable(spi100k->fck);
+	spin_unlock_irq(&spi100k->lock);
+
+	if (status < 0)
+		printk(KERN_WARNING "spi transfer failed with %d\n", status);
+}
+
+static int omap1_spi100k_transfer(struct spi_device *spi, struct spi_message *m)
+{
+	struct omap1_spi100k    *spi100k;
+	unsigned long           flags;
+	struct spi_transfer     *t;
+
+	m->actual_length = 0;
+	m->status = -EINPROGRESS;
+
+	spi100k = spi_master_get_devdata(spi->master);
+
+	/* Don't accept new work if we're shutting down */
+	if (spi100k->state == SPI_SHUTDOWN)
+		return -ESHUTDOWN;
+
+	/* reject invalid messages and transfers */
+	if (list_empty(&m->transfers) || !m->complete)
+		return -EINVAL;
+
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		const void      *tx_buf = t->tx_buf;
+		void            *rx_buf = t->rx_buf;
+		unsigned        len = t->len;
+
+		if (t->speed_hz > OMAP1_SPI100K_MAX_FREQ
+				|| (len && !(rx_buf || tx_buf))
+				|| (t->bits_per_word &&
+					(  t->bits_per_word < 4
+					|| t->bits_per_word > 32))) {
+			dev_dbg(&spi->dev, "transfer: %d Hz, %d %s%s, %d bpw\n",
+					t->speed_hz,
+					len,
+					tx_buf ? "tx" : "",
+					rx_buf ? "rx" : "",
+					t->bits_per_word);
+			return -EINVAL;
+		}
+
+		if (t->speed_hz && t->speed_hz < OMAP1_SPI100K_MAX_FREQ/(1<<16)) {
+			dev_dbg(&spi->dev, "%d Hz max exceeds %d\n",
+					t->speed_hz,
+					OMAP1_SPI100K_MAX_FREQ/(1<<16));
+			return -EINVAL;
+		}
+
+	}
+
+	spin_lock_irqsave(&spi100k->lock, flags);
+	list_add_tail(&m->queue, &spi100k->msg_queue);
+	queue_work(omap1_spi100k_wq, &spi100k->work);
+	spin_unlock_irqrestore(&spi100k->lock, flags);
+
+	return 0;
+}
+
+static int __init omap1_spi100k_reset(struct omap1_spi100k *spi100k)
+{
+	return 0;
+}
+
+static int __devinit omap1_spi100k_probe(struct platform_device *pdev)
+{
+	struct spi_master       *master;
+	struct omap1_spi100k    *spi100k;
+	struct resource         *r;
+	int                     status = 0;
+
+	if ( !pdev->id)
+		return -EINVAL;
+
+	master = spi_alloc_master(&pdev->dev, sizeof *spi100k);
+	if (master == NULL) {
+		dev_dbg(&pdev->dev, "master allocation failed\n");
+		return -ENOMEM;
+	}
+
+	if (pdev->id != -1)
+	       master->bus_num = pdev->id;
+
+	master->setup = omap1_spi100k_setup;
+	master->transfer = omap1_spi100k_transfer;
+	master->cleanup = NULL;
+	master->num_chipselect =2;
+	master->mode_bits = MODEBITS;
+
+	dev_set_drvdata(&pdev->dev, master);
+
+	spi100k = spi_master_get_devdata(master);
+	spi100k->master = master;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (r == NULL) {
+		 status = -ENODEV;
+		 goto err1;
+	}
+	if (!request_mem_region(r->start, (r->end - r->start) + 1,
+			pdev->name)) {
+	       status = -EBUSY;
+	       goto err1;
+	}
+
+	spi100k->base = (void __iomem *) OMAP2_L3_IO_ADDRESS(r->start);
+	spi100k->base_addr = (unsigned long)r->start;
+	INIT_WORK(&spi100k->work, omap1_spi100k_work);
+
+	spin_lock_init(&spi100k->lock);
+	INIT_LIST_HEAD(&spi100k->msg_queue);
+	spi100k->ick = clk_get(&pdev->dev, "ick");
+	if (IS_ERR(spi100k->ick)) {
+		dev_dbg(&pdev->dev, "can't get spi100k_ick\n");
+		status = PTR_ERR(spi100k->ick);
+		goto err1a;
+	}
+
+	spi100k->fck = clk_get(&pdev->dev, "fck");
+	if (IS_ERR(spi100k->fck)) {
+		dev_dbg(&pdev->dev, "can't get spi100k_fck\n");
+		status = PTR_ERR(spi100k->fck);
+		goto err2;
+	}
+
+	if (omap1_spi100k_reset(spi100k) < 0)
+		goto err3;
+
+	status = spi_register_master(master);
+	if (status < 0)
+		goto err3;
+
+	spi100k->state = SPI_RUNNING;
+
+	printk(KERN_INFO "spi Registered\n");
+	return status;
+
+err3:
+	clk_put(spi100k->fck);
+err2:
+	clk_put(spi100k->ick);
+err1a:
+	release_mem_region(r->start, (r->end - r->start) + 1);
+err1:
+	spi_master_put(master);
+	printk(KERN_INFO "Error: spi\n");
+	return status;
+}
+
+static int __exit omap1_spi100k_remove(struct platform_device *pdev)
+{
+	struct spi_master       *master;
+	struct omap1_spi100k    *spi100k;
+	struct resource         *r;
+	unsigned		limit = 500;
+	unsigned long		flags;
+	int			status = 0;
+
+	master = dev_get_drvdata(&pdev->dev);
+	spi100k = spi_master_get_devdata(master);
+
+	spin_lock_irqsave(&spi100k->lock, flags);
+
+	spi100k->state = SPI_SHUTDOWN;
+	while (!list_empty(&spi100k->msg_queue) && limit--) {
+		spin_unlock_irqrestore(&spi100k->lock, flags);
+		msleep(10);
+		spin_lock_irqsave(&spi100k->lock, flags);
+	}
+
+	if (!list_empty(&spi100k->msg_queue))
+		status = -EBUSY;
+
+	spin_unlock_irqrestore(&spi100k->lock, flags);
+
+	if (status != 0)
+		return status;
+
+	clk_put(spi100k->fck);
+	clk_put(spi100k->ick);
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(r->start, (r->end - r->start) + 1);
+
+	spi_unregister_master(master);
+
+	return 0;
+}
+
+static struct platform_driver omap1_spi100k_driver = {
+	.driver = {
+		.name		= "omap1_spi100k",
+		.owner		= THIS_MODULE,
+	},
+	.probe		= omap1_spi100k_probe,
+	.remove		= __exit_p(omap1_spi100k_remove),
+};
+
+
+static int __init omap1_spi100k_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "In spi init\n");
+	omap1_spi100k_wq = create_singlethread_workqueue(
+			omap1_spi100k_driver.driver.name);
+
+	if (omap1_spi100k_wq == NULL) {
+		printk(KERN_INFO "Error: spi init\n");
+		return -1;
+	}
+
+	ret = platform_driver_register(&omap1_spi100k_driver);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void __exit omap1_spi100k_exit(void)
+{
+	platform_driver_unregister(&omap1_spi100k_driver);
+
+	destroy_workqueue(omap1_spi100k_wq);
+}
+
+module_init(omap1_spi100k_init);
+module_exit(omap1_spi100k_exit);
+
+MODULE_DESCRIPTION("OMAP7xx SPI 100k controller driver");
+MODULE_AUTHOR("Fabrice Crohas <fcrohas@gmail.com>");
+MODULE_LICENSE("GPL");
+
-- 
1.6.3.3

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html