From: srinath@mistralsolutions.com To: linux-omap@vger.kernel.org Cc: jdk@ti.com, tony@atomide.com, linux-kernel@vger.kernel.org, linux@arm.linux.org.uk, linux-arm-kernel@lists.infradead.org, khilman@deeprootsystems.com, nm@ti.com, nagendra@mistralsolutions.com, umeshk@mistralsolutions.com, Srinath <srinath@mistralsolutions.com> Subject: [Patch v3] AM35xx: Craneboard: Add USB EHCI support Date: Wed, 1 Dec 2010 22:28:50 +0530 [thread overview] Message-ID: <1291222730-17614-1-git-send-email-srinath@mistralsolutions.com> (raw) In-Reply-To: <[PATCH] Craneboard: Add USB EHCI Support> From: Srinath <srinath@mistralsolutions.com> AM3517/05 Craneboard has one EHCI interface on board using port1. GPIO35 is used as power enable. GPIO38 is used as port1 PHY reset. History: http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&q=t Signed-off-by: Srinath <srinath@mistralsolutions.com> --- arch/arm/mach-omap2/board-am3517crane.c | 40 +++++++++++++++++++++++++++++++ 1 files changed, 40 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c index 13ead33..6fd5dfe 100644 --- a/arch/arm/mach-omap2/board-am3517crane.c +++ b/arch/arm/mach-omap2/board-am3517crane.c @@ -28,8 +28,13 @@ #include <plat/board.h> #include <plat/common.h> +#include <plat/usb.h> #include "mux.h" +#include "control.h" + +#define GPIO_USB_POWER 35 +#define GPIO_USB_NRESET 38 /* Board initialization */ static struct omap_board_config_kernel am3517_crane_config[] __initdata = { @@ -53,10 +58,45 @@ static void __init am3517_crane_init_irq(void) omap_gpio_init(); } +static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = { + .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN, + .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, + + .phy_reset = true, + .reset_gpio_port[0] = GPIO_USB_NRESET, + .reset_gpio_port[1] = -EINVAL, + .reset_gpio_port[2] = -EINVAL +}; + static void __init am3517_crane_init(void) { + int ret; + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); omap_serial_init(); + + /* Configure GPIO for EHCI port */ + omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT); + + ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable"); + if (ret < 0) { + pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER); + return; + } + + ret = gpio_direction_output(GPIO_USB_POWER, 1); + if (ret < 0) + goto err; + + omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT); + usb_ehci_init(&ehci_pdata); + return; + +err: + gpio_free(GPIO_USB_POWER); + pr_err("Unable to initialize EHCI power\n"); + return; } MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD") -- 1.7.1.226.g770c5
WARNING: multiple messages have this Message-ID (diff)
From: srinath@mistralsolutions.com (srinath at mistralsolutions.com) To: linux-arm-kernel@lists.infradead.org Subject: [Patch v3] AM35xx: Craneboard: Add USB EHCI support Date: Wed, 1 Dec 2010 22:28:50 +0530 [thread overview] Message-ID: <1291222730-17614-1-git-send-email-srinath@mistralsolutions.com> (raw) In-Reply-To: <[PATCH] Craneboard: Add USB EHCI Support> From: Srinath <srinath@mistralsolutions.com> AM3517/05 Craneboard has one EHCI interface on board using port1. GPIO35 is used as power enable. GPIO38 is used as port1 PHY reset. History: http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&q=t Signed-off-by: Srinath <srinath@mistralsolutions.com> --- arch/arm/mach-omap2/board-am3517crane.c | 40 +++++++++++++++++++++++++++++++ 1 files changed, 40 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c index 13ead33..6fd5dfe 100644 --- a/arch/arm/mach-omap2/board-am3517crane.c +++ b/arch/arm/mach-omap2/board-am3517crane.c @@ -28,8 +28,13 @@ #include <plat/board.h> #include <plat/common.h> +#include <plat/usb.h> #include "mux.h" +#include "control.h" + +#define GPIO_USB_POWER 35 +#define GPIO_USB_NRESET 38 /* Board initialization */ static struct omap_board_config_kernel am3517_crane_config[] __initdata = { @@ -53,10 +58,45 @@ static void __init am3517_crane_init_irq(void) omap_gpio_init(); } +static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = { + .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN, + .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, + + .phy_reset = true, + .reset_gpio_port[0] = GPIO_USB_NRESET, + .reset_gpio_port[1] = -EINVAL, + .reset_gpio_port[2] = -EINVAL +}; + static void __init am3517_crane_init(void) { + int ret; + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); omap_serial_init(); + + /* Configure GPIO for EHCI port */ + omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT); + + ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable"); + if (ret < 0) { + pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER); + return; + } + + ret = gpio_direction_output(GPIO_USB_POWER, 1); + if (ret < 0) + goto err; + + omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT); + usb_ehci_init(&ehci_pdata); + return; + +err: + gpio_free(GPIO_USB_POWER); + pr_err("Unable to initialize EHCI power\n"); + return; } MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD") -- 1.7.1.226.g770c5
next parent reply other threads:[~2010-12-01 17:23 UTC|newest] Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top [not found] <[PATCH] Craneboard: Add USB EHCI Support> 2010-12-01 16:58 ` srinath [this message] 2010-12-01 16:58 ` [Patch v3] AM35xx: Craneboard: Add USB EHCI support srinath at mistralsolutions.com 2010-12-02 6:25 ` G, Manjunath Kondaiah 2010-12-02 6:25 ` G, Manjunath Kondaiah 2010-12-02 7:21 ` Srinath R 2010-12-02 7:21 ` Srinath R 2010-12-02 7:21 ` Srinath R
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1291222730-17614-1-git-send-email-srinath@mistralsolutions.com \ --to=srinath@mistralsolutions.com \ --cc=jdk@ti.com \ --cc=khilman@deeprootsystems.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=linux@arm.linux.org.uk \ --cc=nagendra@mistralsolutions.com \ --cc=nm@ti.com \ --cc=tony@atomide.com \ --cc=umeshk@mistralsolutions.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.