All of lore.kernel.org
 help / color / mirror / Atom feed
From: srinath@mistralsolutions.com
To: linux-omap@vger.kernel.org
Cc: jdk@ti.com, tony@atomide.com, linux-kernel@vger.kernel.org,
	linux@arm.linux.org.uk, linux-arm-kernel@lists.infradead.org,
	khilman@deeprootsystems.com, nagendra@mistralsolutions.com,
	umeshk@mistralsolutions.com, sshtylyov@mvista.com,
	manjugk@ti.com, babli@ti.com,
	Srinath <srinath@mistralsolutions.com>
Subject: [Patch v5] AM35xx: Craneboard: Add USB EHCI support
Date: Mon, 20 Dec 2010 18:38:43 +0530	[thread overview]
Message-ID: <1292850523-14583-1-git-send-email-srinath@mistralsolutions.com> (raw)
In-Reply-To: <[PATCH] AM35xx-Craneboard-Add-USB-EHCI-support>

From: Srinath <srinath@mistralsolutions.com>

AM3517/05 Craneboard has one EHCI interface on board using port1.

GPIO35 is used as power enable.
GPIO38 is used as port1 PHY reset.

History:
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%253A%2BAdd%2BUSB%2BEHCI%2Bsupport&q=b

Signed-off-by: Srinath <srinath@mistralsolutions.com>
---
 arch/arm/mach-omap2/board-am3517crane.c |   48 +++++++++++++++++++++++++++++++
 1 files changed, 48 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 8ba4047..e56900f 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -19,6 +19,7 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -27,8 +28,14 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
+#include <plat/usb.h>
 
 #include "mux.h"
+#include "control.h"
+
+#define GPIO_USB_POWER		35
+#define GPIO_USB_NRESET		38
+
 
 /* Board initialization */
 static struct omap_board_config_kernel am3517_crane_config[] __initdata = {
@@ -51,10 +58,51 @@ static void __init am3517_crane_init_irq(void)
 	omap_init_irq();
 }
 
+static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+	.port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+	.phy_reset  = true,
+	.reset_gpio_port[0]  = GPIO_USB_NRESET,
+	.reset_gpio_port[1]  = -EINVAL,
+	.reset_gpio_port[2]  = -EINVAL
+};
+
 static void __init am3517_crane_init(void)
 {
+	int ret;
+
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap_serial_init();
+
+	/* Configure GPIO for EHCI port */
+	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
+		pr_err("Can not configure mux for GPIO_USB_NRESET %d\n",
+			GPIO_USB_NRESET);
+		return;
+	}
+
+	if (omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT)) {
+		pr_err("Can not configure mux for GPIO_USB_POWER %d\n",
+			GPIO_USB_POWER);
+		return;
+	}
+
+	ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
+	if (ret < 0) {
+		pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
+		return;
+	}
+
+	ret = gpio_direction_output(GPIO_USB_POWER, 1);
+	if (ret < 0) {
+		gpio_free(GPIO_USB_POWER);
+		pr_err("Unable to initialize EHCI power\n");
+		return;
+	}
+
+	usb_ehci_init(&ehci_pdata);
 }
 
 MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
-- 
1.7.1.226.g770c5


WARNING: multiple messages have this Message-ID (diff)
From: srinath@mistralsolutions.com (srinath at mistralsolutions.com)
To: linux-arm-kernel@lists.infradead.org
Subject: [Patch v5] AM35xx: Craneboard: Add USB EHCI support
Date: Mon, 20 Dec 2010 18:38:43 +0530	[thread overview]
Message-ID: <1292850523-14583-1-git-send-email-srinath@mistralsolutions.com> (raw)
In-Reply-To: <[PATCH] AM35xx-Craneboard-Add-USB-EHCI-support>

From: Srinath <srinath@mistralsolutions.com>

AM3517/05 Craneboard has one EHCI interface on board using port1.

GPIO35 is used as power enable.
GPIO38 is used as port1 PHY reset.

History:
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%253A%2BAdd%2BUSB%2BEHCI%2Bsupport&q=b

Signed-off-by: Srinath <srinath@mistralsolutions.com>
---
 arch/arm/mach-omap2/board-am3517crane.c |   48 +++++++++++++++++++++++++++++++
 1 files changed, 48 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 8ba4047..e56900f 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -19,6 +19,7 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -27,8 +28,14 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
+#include <plat/usb.h>
 
 #include "mux.h"
+#include "control.h"
+
+#define GPIO_USB_POWER		35
+#define GPIO_USB_NRESET		38
+
 
 /* Board initialization */
 static struct omap_board_config_kernel am3517_crane_config[] __initdata = {
@@ -51,10 +58,51 @@ static void __init am3517_crane_init_irq(void)
 	omap_init_irq();
 }
 
+static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+	.port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+	.phy_reset  = true,
+	.reset_gpio_port[0]  = GPIO_USB_NRESET,
+	.reset_gpio_port[1]  = -EINVAL,
+	.reset_gpio_port[2]  = -EINVAL
+};
+
 static void __init am3517_crane_init(void)
 {
+	int ret;
+
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap_serial_init();
+
+	/* Configure GPIO for EHCI port */
+	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
+		pr_err("Can not configure mux for GPIO_USB_NRESET %d\n",
+			GPIO_USB_NRESET);
+		return;
+	}
+
+	if (omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT)) {
+		pr_err("Can not configure mux for GPIO_USB_POWER %d\n",
+			GPIO_USB_POWER);
+		return;
+	}
+
+	ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
+	if (ret < 0) {
+		pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
+		return;
+	}
+
+	ret = gpio_direction_output(GPIO_USB_POWER, 1);
+	if (ret < 0) {
+		gpio_free(GPIO_USB_POWER);
+		pr_err("Unable to initialize EHCI power\n");
+		return;
+	}
+
+	usb_ehci_init(&ehci_pdata);
 }
 
 MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
-- 
1.7.1.226.g770c5

  parent reply	other threads:[~2010-12-20 13:37 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <[PATCH] AM35xx-Craneboard-Add-USB-EHCI-support>
2010-11-19 16:07 ` [Patch v1] AM35xx: Craneboard: Add USB EHCI support srinath
2010-11-19 16:07   ` srinath at mistralsolutions.com
2010-11-19 16:59   ` Igor Grinberg
2010-11-19 16:59     ` Igor Grinberg
2010-11-20 11:39   ` Sergei Shtylyov
2010-11-20 11:39     ` Sergei Shtylyov
2010-11-22  8:55     ` Srinath R
2010-11-22  8:55       ` Srinath R
2010-11-22  8:55       ` Srinath R
2010-11-22  8:32 ` [Patch v2] " srinath
2010-11-22  8:32   ` srinath at mistralsolutions.com
2010-11-22 17:56   ` Kevin Hilman
2010-11-22 17:56     ` Kevin Hilman
2010-12-16 15:25 ` [Patch v4] " srinath
2010-12-16 15:25   ` srinath at mistralsolutions.com
2010-12-17  6:22   ` Felipe Balbi
2010-12-17  6:22     ` Felipe Balbi
2010-12-17 12:45   ` Sergei Shtylyov
2010-12-17 12:45     ` Sergei Shtylyov
2010-12-20 13:08 ` srinath [this message]
2010-12-20 13:08   ` [Patch v5] " srinath at mistralsolutions.com
2010-12-21  6:58   ` Felipe Balbi
2010-12-21  6:58     ` Felipe Balbi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1292850523-14583-1-git-send-email-srinath@mistralsolutions.com \
    --to=srinath@mistralsolutions.com \
    --cc=babli@ti.com \
    --cc=jdk@ti.com \
    --cc=khilman@deeprootsystems.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=linux@arm.linux.org.uk \
    --cc=manjugk@ti.com \
    --cc=nagendra@mistralsolutions.com \
    --cc=sshtylyov@mvista.com \
    --cc=tony@atomide.com \
    --cc=umeshk@mistralsolutions.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.