All of lore.kernel.org
 help / color / mirror / Atom feed
From: Adrian Hunter <adrian.hunter@nokia.com>
To: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>,
	linux-omap Mailing List <linux-omap@vger.kernel.org>,
	linux-mmc Mailing List <linux-mmc@vger.kernel.org>,
	linux-arm Mailing List <linux-arm-kernel@lists.infradead.org>,
	Andy Shevchenko <ext-andriy.shevchenko@nokia.com>,
	Adrian Hunter <adrian.hunter@nokia.com>
Subject: [PATCH 13/22] mmc: omap_hsmmc: fix few bugs when set the clock divisor
Date: Thu,  5 May 2011 14:51:13 +0300	[thread overview]
Message-ID: <1304596282-4095-14-git-send-email-adrian.hunter@nokia.com> (raw)
In-Reply-To: <1304596282-4095-1-git-send-email-adrian.hunter@nokia.com>

From: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>

There are two pieces of code which similar, but not the same. Each of them
contains a bug.

The SYSCTL register should be read before write in the
omap_hsmmc_context_restore() to remain the state of the reserved bits.

Before set the clock divisor and DTO bits the value from the SYSCTL register
should be masked properly. We were lucky to have no problems with DTO bits. So,
make sure we have clear DTO bits properly in the omap_hsmmc_set_ios().

Additionally get rid of msleep(1). The actual time rare higher than 30us on
OMAP 3630.

The result pieces of code are split to omap_hsmmc_set_clock() function.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
---
 drivers/mmc/host/omap_hsmmc.c |   59 +++++++++++++++++++---------------------
 1 files changed, 28 insertions(+), 31 deletions(-)

diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index ae6d204..3c76911 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -619,6 +619,32 @@ static u16 calc_divisor(struct mmc_ios *ios)
 	return dsor;
 }
 
+static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
+{
+	struct mmc_ios *ios = &host->mmc->ios;
+	unsigned long regval;
+	unsigned long timeout;
+
+	dev_dbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock);
+
+	omap_hsmmc_stop_clock(host);
+
+	regval = OMAP_HSMMC_READ(host->base, SYSCTL);
+	regval = regval & ~(CLKD_MASK | DTO_MASK);
+	regval = regval | (calc_divisor(ios) << 6) | (DTO << 16);
+	OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
+	OMAP_HSMMC_WRITE(host->base, SYSCTL,
+		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
+
+	/* Wait till the ICS bit is set */
+	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
+		&& time_before(jiffies, timeout))
+		;
+
+	omap_hsmmc_start_clock(host);
+}
+
 #ifdef CONFIG_PM
 
 /*
@@ -709,19 +735,7 @@ static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
 		break;
 	}
 
-	omap_hsmmc_stop_clock(host);
-
-	OMAP_HSMMC_WRITE(host->base, SYSCTL,
-		(calc_divisor(ios) << 6) | (DTO << 16));
-	OMAP_HSMMC_WRITE(host->base, SYSCTL,
-		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
-
-	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
-	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
-		&& time_before(jiffies, timeout))
-		;
-
-	omap_hsmmc_start_clock(host);
+	omap_hsmmc_set_clock(host);
 
 	con = OMAP_HSMMC_READ(host->base, CON);
 	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
@@ -1622,8 +1636,6 @@ static void omap_hsmmc_request(struct mmc_host *mmc, struct mmc_request *req)
 static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct omap_hsmmc_host *host = mmc_priv(mmc);
-	unsigned long regval;
-	unsigned long timeout;
 	u32 con;
 	int do_send_init_stream = 0;
 
@@ -1685,22 +1697,7 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		}
 	}
 
-	omap_hsmmc_stop_clock(host);
-
-	regval = OMAP_HSMMC_READ(host->base, SYSCTL);
-	regval = regval & ~(CLKD_MASK);
-	regval = regval | (calc_divisor(ios) << 6) | (DTO << 16);
-	OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
-	OMAP_HSMMC_WRITE(host->base, SYSCTL,
-		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
-
-	/* Wait till the ICS bit is set */
-	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
-	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
-		&& time_before(jiffies, timeout))
-		msleep(1);
-
-	omap_hsmmc_start_clock(host);
+	omap_hsmmc_set_clock(host);
 
 	if (do_send_init_stream)
 		send_init_stream(host);
-- 
1.7.0.4


WARNING: multiple messages have this Message-ID (diff)
From: adrian.hunter@nokia.com (Adrian Hunter)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 13/22] mmc: omap_hsmmc: fix few bugs when set the clock divisor
Date: Thu,  5 May 2011 14:51:13 +0300	[thread overview]
Message-ID: <1304596282-4095-14-git-send-email-adrian.hunter@nokia.com> (raw)
In-Reply-To: <1304596282-4095-1-git-send-email-adrian.hunter@nokia.com>

From: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>

There are two pieces of code which similar, but not the same. Each of them
contains a bug.

The SYSCTL register should be read before write in the
omap_hsmmc_context_restore() to remain the state of the reserved bits.

Before set the clock divisor and DTO bits the value from the SYSCTL register
should be masked properly. We were lucky to have no problems with DTO bits. So,
make sure we have clear DTO bits properly in the omap_hsmmc_set_ios().

Additionally get rid of msleep(1). The actual time rare higher than 30us on
OMAP 3630.

The result pieces of code are split to omap_hsmmc_set_clock() function.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
---
 drivers/mmc/host/omap_hsmmc.c |   59 +++++++++++++++++++---------------------
 1 files changed, 28 insertions(+), 31 deletions(-)

diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index ae6d204..3c76911 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -619,6 +619,32 @@ static u16 calc_divisor(struct mmc_ios *ios)
 	return dsor;
 }
 
+static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
+{
+	struct mmc_ios *ios = &host->mmc->ios;
+	unsigned long regval;
+	unsigned long timeout;
+
+	dev_dbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock);
+
+	omap_hsmmc_stop_clock(host);
+
+	regval = OMAP_HSMMC_READ(host->base, SYSCTL);
+	regval = regval & ~(CLKD_MASK | DTO_MASK);
+	regval = regval | (calc_divisor(ios) << 6) | (DTO << 16);
+	OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
+	OMAP_HSMMC_WRITE(host->base, SYSCTL,
+		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
+
+	/* Wait till the ICS bit is set */
+	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
+		&& time_before(jiffies, timeout))
+		;
+
+	omap_hsmmc_start_clock(host);
+}
+
 #ifdef CONFIG_PM
 
 /*
@@ -709,19 +735,7 @@ static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
 		break;
 	}
 
-	omap_hsmmc_stop_clock(host);
-
-	OMAP_HSMMC_WRITE(host->base, SYSCTL,
-		(calc_divisor(ios) << 6) | (DTO << 16));
-	OMAP_HSMMC_WRITE(host->base, SYSCTL,
-		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
-
-	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
-	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
-		&& time_before(jiffies, timeout))
-		;
-
-	omap_hsmmc_start_clock(host);
+	omap_hsmmc_set_clock(host);
 
 	con = OMAP_HSMMC_READ(host->base, CON);
 	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
@@ -1622,8 +1636,6 @@ static void omap_hsmmc_request(struct mmc_host *mmc, struct mmc_request *req)
 static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct omap_hsmmc_host *host = mmc_priv(mmc);
-	unsigned long regval;
-	unsigned long timeout;
 	u32 con;
 	int do_send_init_stream = 0;
 
@@ -1685,22 +1697,7 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		}
 	}
 
-	omap_hsmmc_stop_clock(host);
-
-	regval = OMAP_HSMMC_READ(host->base, SYSCTL);
-	regval = regval & ~(CLKD_MASK);
-	regval = regval | (calc_divisor(ios) << 6) | (DTO << 16);
-	OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
-	OMAP_HSMMC_WRITE(host->base, SYSCTL,
-		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
-
-	/* Wait till the ICS bit is set */
-	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
-	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
-		&& time_before(jiffies, timeout))
-		msleep(1);
-
-	omap_hsmmc_start_clock(host);
+	omap_hsmmc_set_clock(host);
 
 	if (do_send_init_stream)
 		send_init_stream(host);
-- 
1.7.0.4

  parent reply	other threads:[~2011-05-05 11:51 UTC|newest]

Thread overview: 56+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-05-05 11:51 [PATCH 00/22] omap_hsmmc patches Adrian Hunter
2011-05-05 11:51 ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 01/22] OMAP: sDMA: descriptor autoloading feature Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-06  6:22   ` Tony Lindgren
2011-05-06  6:22     ` Tony Lindgren
2011-05-05 11:51 ` [PATCH 02/22] OMAP: DMA: add omap_dma_has_sglist() Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 03/22] OMAP: DMA: Ensure the sglist registers are cleared Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 04/22] mmc: omap hsmmc: adaptation of sdma descriptor Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 05/22] mmc: omap_hsmmc: fix dma sglist use Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 06/22] mmc: omap_hsmmc: limit scatterlist size for sDMA autoloading Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 07/22] mmc: omap_hsmmc: fix missing mmc_release_host() in no_off case Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 13:08   ` Sergei Shtylyov
2011-05-05 13:08     ` Sergei Shtylyov
2011-05-05 11:51 ` [PATCH 08/22] mmc: omap_hsmmc: correct debug report error status mnemonics Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-06  8:35   ` S, Venkatraman
2011-05-06  8:35     ` S, Venkatraman
2011-05-05 11:51 ` [PATCH 09/22] mmc: omap_hsmmc: move hardcoded frequency constants to definition block Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 10/22] mmc: omap_hsmmc: reduce a bit the error handlers in probe() Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 11/22] mmc: omap_hsmmc: split duplicate code to calc_divisor() function Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 12/22] mmc: omap_hsmmc: introduce start_clock and re-use stop_clock Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` Adrian Hunter [this message]
2011-05-05 11:51   ` [PATCH 13/22] mmc: omap_hsmmc: fix few bugs when set the clock divisor Adrian Hunter
2011-05-05 12:53   ` Grazvydas Ignotas
2011-05-05 12:53     ` Grazvydas Ignotas
2011-05-05 11:51 ` [PATCH 14/22] mmc: omap_hsmmc: split same pieces of code to separate functions Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 15/22] OMAP: hsmmc: Do not mux the slot if non default muxing is already done Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 16/22] OMAP: board-rm680: set MMC nomux flag Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 17/22] mmc: omap_hsmmc: ensure pbias configuration is always done Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 18/22] mmc: omap_hsmmc: fix oops in omap_hsmmc_dma_cb Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 19/22] OMAP: hsmmc: implement clock switcher Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 13:34   ` Grazvydas Ignotas
2011-05-05 13:34     ` Grazvydas Ignotas
2011-05-05 11:51 ` [PATCH 20/22] mmc: omap_hsmmc: adjust host controller clock in regard to current OPP Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 21/22] OMAP: hsmmc: add platform data for eMMC hardware reset gpio Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter
2011-05-05 11:51 ` [PATCH 22/22] mmc: omap_hsmmc: add a hardware reset before initialization Adrian Hunter
2011-05-05 11:51   ` Adrian Hunter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1304596282-4095-14-git-send-email-adrian.hunter@nokia.com \
    --to=adrian.hunter@nokia.com \
    --cc=ext-andriy.shevchenko@nokia.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=madhu.cr@ti.com \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.