From: Tony Lin <tony.lin@freescale.com> To: linux-mmc@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org, cjb@laptop.org Subject: [PATCH 1/1] fix card interrupt losing issue on freescale eSDHC Date: Mon, 18 Jul 2011 13:20:02 +0800 [thread overview] Message-ID: <1310966402-12318-1-git-send-email-tony.lin@freescale.com> (raw) apply workaround for imx eSDHC controller to avoid missing card interrupt so that SDIO function is workable Signed-off-by: Tony Lin <tony.lin@freescale.com> --- drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++-------- 1 files changed, 30 insertions(+), 9 deletions(-) diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index a19967d..da77cae 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -32,6 +32,8 @@ #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) + +#define SDHCI_CTRL_D3CD 0x08 /* * The CMDTYPE of the CMD register (offset 0xE) should be set to * "11" when the STOP CMD12 is issued on imx53 to abort one @@ -87,14 +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct pltfm_imx_data *imx_data = pltfm_host->priv; - - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) - /* - * these interrupts won't work with a custom card_detect gpio - * (only applied to mx25/35) - */ - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); + u32 data; + + if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))) { + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) + /* + * these interrupts won't work with a custom + * card_detect gpio (only applied to mx25/35) + */ + val &= ~(SDHCI_INT_CARD_REMOVE | \ + SDHCI_INT_CARD_INSERT); + + if (val & SDHCI_INT_CARD_INT) { + /* + * clear D3CD bit and set D3CD bit to avoid + * missing card interrupt + * this is a eSDHC controller problem so that + * we need to apply following workaround + */ + data = readl(host->ioaddr + SDHCI_HOST_CONTROL); + data &= ~SDHCI_CTRL_D3CD; + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); + data |= SDHCI_CTRL_D3CD; + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); + } + } if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) && (reg == SDHCI_INT_STATUS) @@ -165,7 +184,9 @@ static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) return; case SDHCI_HOST_CONTROL: /* FSL messed up here, so we can just keep those two */ - new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); + new_val = val & (SDHCI_CTRL_LED | \ + SDHCI_CTRL_4BITBUS | \ + SDHCI_CTRL_D3CD); /* ensure the endianess */ new_val |= ESDHC_HOST_CONTROL_LE; /* DMA mode bits are shifted */ -- 1.7.0.4
WARNING: multiple messages have this Message-ID (diff)
From: tony.lin@freescale.com (Tony Lin) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 1/1] fix card interrupt losing issue on freescale eSDHC Date: Mon, 18 Jul 2011 13:20:02 +0800 [thread overview] Message-ID: <1310966402-12318-1-git-send-email-tony.lin@freescale.com> (raw) apply workaround for imx eSDHC controller to avoid missing card interrupt so that SDIO function is workable Signed-off-by: Tony Lin <tony.lin@freescale.com> --- drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++-------- 1 files changed, 30 insertions(+), 9 deletions(-) diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index a19967d..da77cae 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -32,6 +32,8 @@ #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) + +#define SDHCI_CTRL_D3CD 0x08 /* * The CMDTYPE of the CMD register (offset 0xE) should be set to * "11" when the STOP CMD12 is issued on imx53 to abort one @@ -87,14 +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct pltfm_imx_data *imx_data = pltfm_host->priv; - - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) - /* - * these interrupts won't work with a custom card_detect gpio - * (only applied to mx25/35) - */ - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); + u32 data; + + if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))) { + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) + /* + * these interrupts won't work with a custom + * card_detect gpio (only applied to mx25/35) + */ + val &= ~(SDHCI_INT_CARD_REMOVE | \ + SDHCI_INT_CARD_INSERT); + + if (val & SDHCI_INT_CARD_INT) { + /* + * clear D3CD bit and set D3CD bit to avoid + * missing card interrupt + * this is a eSDHC controller problem so that + * we need to apply following workaround + */ + data = readl(host->ioaddr + SDHCI_HOST_CONTROL); + data &= ~SDHCI_CTRL_D3CD; + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); + data |= SDHCI_CTRL_D3CD; + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); + } + } if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) && (reg == SDHCI_INT_STATUS) @@ -165,7 +184,9 @@ static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) return; case SDHCI_HOST_CONTROL: /* FSL messed up here, so we can just keep those two */ - new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); + new_val = val & (SDHCI_CTRL_LED | \ + SDHCI_CTRL_4BITBUS | \ + SDHCI_CTRL_D3CD); /* ensure the endianess */ new_val |= ESDHC_HOST_CONTROL_LE; /* DMA mode bits are shifted */ -- 1.7.0.4
next reply other threads:[~2011-07-18 4:55 UTC|newest] Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top 2011-07-18 5:20 Tony Lin [this message] 2011-07-18 5:20 ` [PATCH 1/1] fix card interrupt losing issue on freescale eSDHC Tony Lin 2011-07-27 6:38 ` Lin Tony-B19295 2011-07-27 6:38 ` Lin Tony-B19295 2011-07-27 7:47 ` Uwe Kleine-König 2011-07-27 7:47 ` Uwe Kleine-König 2011-07-27 9:27 ` Lin Tony-B19295 2011-07-27 9:27 ` Lin Tony-B19295 2011-07-27 9:42 ` Arnaud Patard 2011-07-27 9:42 ` Arnaud Patard (Rtp)
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1310966402-12318-1-git-send-email-tony.lin@freescale.com \ --to=tony.lin@freescale.com \ --cc=cjb@laptop.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-mmc@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.