[PATCH v5 1/3] PM: Introduce DEVFREQ: generic DVFS framework with device-specific OPPs

[MyungJoo Ham <myungjoo.ham@samsung.com>]

With OPPs, a device may have multiple operable frequency and voltage
sets. However, there can be multiple possible operable sets and a system
will need to choose one from them. In order to reduce the power
consumption (by reducing frequency and voltage) without affecting the
performance too much, a Dynamic Voltage and Frequency Scaling (DVFS)
scheme may be used.

This patch introduces the DVFS capability to non-CPU devices with OPPs.
DVFS is a techique whereby the frequency and supplied voltage of a
device is adjusted on-the-fly. DVFS usually sets the frequency as low
as possible with given conditions (such as QoS assurance) and adjusts
voltage according to the chosen frequency in order to reduce power
consumption and heat dissipation.

The generic DVFS for devices, DEVFREQ, may appear quite similar with
/drivers/cpufreq.  However, CPUFREQ does not allow to have multiple
devices registered and is not suitable to have multiple heterogenous
devices with different (but simple) governors.

Normally, DVFS mechanism controls frequency based on the demand for
the device, and then, chooses voltage based on the chosen frequency.
DEVFREQ also controls the frequency based on the governor's frequency
recommendation and let OPP pick up the pair of frequency and voltage
based on the recommended frequency. Then, the chosen OPP is passed to
device driver's "target" callback.

When PM QoS is going to be used with the DEVFREQ device, the device
driver should enable OPPs that are appropriate with the current PM QoS
requests. In order to do so, the device driver may call opp_enable and
opp_disable at the notifier callback of PM QoS so that PM QoS's
update_target() call enables the appropriate OPPs. Note that at least
one of OPPs should be enabled at any time; be careful when there is a
transition.

Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

---
Tested with memory bus of Exynos4-NURI board.

The test code with board support for Exynos4-NURI is at
http://git.infradead.org/users/kmpark/linux-2.6-samsung/shortlog/refs/heads/devfreq

---
Thank you for your valuable comments, Rafael, Greg, Pavel, Colin, Mike,
and Kevin.

Changed from v4
- Removed tickle, which is a duplicated feature; PM QoS can do the same.
- Allow to extend polling interval if devices have longer polling intervals.
- Relocated private data of governors.
- Removed system-wide sysfs

Changed from v3
- In kerneldoc comments, DEVFREQ has ben replaced by devfreq
- Revised removing devfreq entries with error mechanism
- Added and revised comments
- Removed unnecessary codes
- Allow to give a name to a governor
- Bugfix: a tickle call may cancel an older tickle call that is still in
  effect.

Changed from v2
- Code style revised and cleaned up.
- Remove DEVFREQ entries that incur errors except for EAGAIN
- Bug fixed: tickle for devices without polling governors

Changes from v1(RFC)
- Rename: DVFS --> DEVFREQ
- Revised governor design
    . Governor receives the whole struct devfreq
    . Governor should gather usage information (thru get_dev_status)
itself
- Periodic monitoring runs only when needed.
- DEVFREQ no more deals with voltage information directly
- Removed some printks.
- Some cosmetics update
- Use freezable_wq.
---
 drivers/base/power/Makefile  |    1 +
 drivers/base/power/devfreq.c |  303 ++++++++++++++++++++++++++++++++++++++++++
 drivers/base/power/opp.c     |    9 ++
 include/linux/devfreq.h      |  103 ++++++++++++++
 kernel/power/Kconfig         |   34 +++++
 5 files changed, 450 insertions(+), 0 deletions(-)
 create mode 100644 drivers/base/power/devfreq.c
 create mode 100644 include/linux/devfreq.h

diff --git a/drivers/base/power/Makefile b/drivers/base/power/Makefile
index 3647e11..20118dc 100644
--- a/drivers/base/power/Makefile
+++ b/drivers/base/power/Makefile
@@ -4,5 +4,6 @@ obj-$(CONFIG_PM_RUNTIME)	+= runtime.o
 obj-$(CONFIG_PM_TRACE_RTC)	+= trace.o
 obj-$(CONFIG_PM_OPP)	+= opp.o
 obj-$(CONFIG_HAVE_CLK)	+= clock_ops.o
+obj-$(CONFIG_PM_DEVFREQ)	+= devfreq.o
 
 ccflags-$(CONFIG_DEBUG_DRIVER) := -DDEBUG
\ No newline at end of file
diff --git a/drivers/base/power/devfreq.c b/drivers/base/power/devfreq.c
new file mode 100644
index 0000000..6f4bd3a
--- /dev/null
+++ b/drivers/base/power/devfreq.c
@@ -0,0 +1,303 @@
+/*
+ * devfreq: Generic Dynamic Voltage and Frequency Scaling (DVFS) Framework
+ *	    for Non-CPU Devices Based on OPP.
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *	MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/opp.h>
+#include <linux/devfreq.h>
+#include <linux/workqueue.h>
+#include <linux/platform_device.h>
+#include <linux/list.h>
+#include <linux/printk.h>
+#include <linux/hrtimer.h>
+
+/*
+ * devfreq polling interval in ms.
+ * It is recommended to be "jiffy_in_ms" * n, where n is an integer >= 1.
+ */
+static unsigned int devfreq_interval = 20;
+
+/*
+ * devfreq_work periodically (given by devfreq_interval) monitors every
+ * registered device.
+ */
+static bool polling;
+static ktime_t last_polled_at;
+static struct workqueue_struct *devfreq_wq;
+static struct delayed_work devfreq_work;
+
+/* The list of all device-devfreq */
+static LIST_HEAD(devfreq_list);
+static DEFINE_MUTEX(devfreq_list_lock);
+
+/**
+ * find_device_devfreq() - find devfreq struct using device pointer
+ * @dev:	device pointer used to lookup device devfreq.
+ *
+ * Search the list of device devfreqs and return the matched device's
+ * devfreq info. devfreq_list_lock should be held by the caller.
+ */
+static struct devfreq *find_device_devfreq(struct device *dev)
+{
+	struct devfreq *tmp_devfreq;
+
+	if (unlikely(IS_ERR_OR_NULL(dev))) {
+		pr_err("DEVFREQ: %s: Invalid parameters\n", __func__);
+		return ERR_PTR(-EINVAL);
+	}
+
+	list_for_each_entry(tmp_devfreq, &devfreq_list, node) {
+		if (tmp_devfreq->dev == dev)
+			return tmp_devfreq;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+
+/**
+ * devfreq_do() - Check the usage profile of a given device and configure
+ *		frequency and voltage accordingly
+ * @devfreq:	devfreq info of the given device
+ */
+static int devfreq_do(struct devfreq *devfreq)
+{
+	struct opp *opp;
+	unsigned long freq;
+	int err;
+
+	err = devfreq->governor->get_target_freq(devfreq, &freq);
+	if (err)
+		return err;
+
+	opp = opp_find_freq_ceil(devfreq->dev, &freq);
+	if (opp == ERR_PTR(-ENODEV))
+		opp = opp_find_freq_floor(devfreq->dev, &freq);
+
+	if (IS_ERR(opp))
+		return PTR_ERR(opp);
+
+	if (devfreq->previous_freq == freq)
+		return 0;
+
+	err = devfreq->profile->target(devfreq->dev, opp);
+	if (err)
+		return err;
+
+	devfreq->previous_freq = freq;
+	return 0;
+}
+
+/**
+ * devfreq_monitor() - Periodically run devfreq_do()
+ * @work: the work struct used to run devfreq_monitor periodically.
+ *
+ */
+static void devfreq_monitor(struct work_struct *work)
+{
+	struct devfreq *devfreq, *tmp;
+	int error;
+	unsigned int next_poll_min = UINT_MAX;
+	ktime_t now = ktime_get();
+	s64 time_passed = ktime_to_ms(ktime_sub(now, last_polled_at));
+	int iterations_passed = 1;
+
+	/* If n * devfreq_interval has passed, count it */
+	do_div(time_passed, devfreq_interval);
+	if (time_passed > 1)
+		iterations_passed = time_passed;
+	last_polled_at = now;
+
+	mutex_lock(&devfreq_list_lock);
+
+	list_for_each_entry_safe(devfreq, tmp, &devfreq_list, node) {
+		if (devfreq->next_polling == 0)
+			continue;
+
+		/*
+		 * Reduce more next_polling if devfreq_wq took an extra
+		 * delay. (i.e., CPU has been idled.)
+		 */
+		if (devfreq->next_polling <= iterations_passed) {
+			error = devfreq_do(devfreq);
+
+			/* Remove a devfreq with an error. */
+			if (error && error != -EAGAIN) {
+				dev_err(devfreq->dev, "devfreq_do error(%d). "
+					"devfreq is removed from the device\n",
+					error);
+
+				list_del(&devfreq->node);
+				kfree(devfreq);
+
+				continue;
+			}
+			devfreq->next_polling = DIV_ROUND_UP(
+						devfreq->profile->polling_ms,
+						devfreq_interval);
+
+			/* No more polling required (polling_ms changed) */
+			if (devfreq->next_polling == 0)
+				continue;
+		} else {
+			devfreq->next_polling -= iterations_passed;
+		}
+
+		next_poll_min = (next_poll_min > devfreq->next_polling) ?
+				devfreq->next_polling : next_poll_min;
+	}
+
+	if (next_poll_min > 0 && next_poll_min < UINT_MAX) {
+		polling = true;
+		queue_delayed_work(devfreq_wq, &devfreq_work, msecs_to_jiffies(
+					   devfreq_interval * next_poll_min));
+	} else {
+		polling = false;
+	}
+
+	mutex_unlock(&devfreq_list_lock);
+}
+
+/**
+ * devfreq_add_device() - Add devfreq feature to the device
+ * @dev:	the device to add devfreq feature.
+ * @profile:	device-specific profile to run devfreq.
+ * @governor:	the policy to choose frequency.
+ */
+int devfreq_add_device(struct device *dev, struct devfreq_dev_profile *profile,
+		       struct devfreq_governor *governor)
+{
+	struct devfreq *new_devfreq, *devfreq;
+	int err = 0;
+
+	if (!dev || !profile || !governor) {
+		dev_err(dev, "%s: Invalid parameters.\n", __func__);
+		return -EINVAL;
+	}
+
+	mutex_lock(&devfreq_list_lock);
+
+	devfreq = find_device_devfreq(dev);
+	if (!IS_ERR(devfreq)) {
+		dev_err(dev, "%s: Unable to create devfreq for the device. "
+			"It already has one.\n", __func__);
+		err = -EINVAL;
+		goto out;
+	}
+
+	new_devfreq = kzalloc(sizeof(struct devfreq), GFP_KERNEL);
+	if (!new_devfreq) {
+		dev_err(dev, "%s: Unable to create devfreq for the device\n",
+			__func__);
+		err = -ENOMEM;
+		goto out;
+	}
+
+	new_devfreq->dev = dev;
+	new_devfreq->profile = profile;
+	new_devfreq->governor = governor;
+	new_devfreq->next_polling = DIV_ROUND_UP(profile->polling_ms,
+						 devfreq_interval);
+	new_devfreq->previous_freq = profile->initial_freq;
+
+	list_add(&new_devfreq->node, &devfreq_list);
+
+	if (devfreq_wq && new_devfreq->next_polling && !polling) {
+		polling = true;
+		queue_delayed_work(devfreq_wq, &devfreq_work,
+				   msecs_to_jiffies(devfreq_interval));
+	}
+out:
+	mutex_unlock(&devfreq_list_lock);
+
+	return err;
+}
+
+/**
+ * devfreq_remove_device() - Remove devfreq feature from a device.
+ * @device:	the device to remove devfreq feature.
+ */
+int devfreq_remove_device(struct device *dev)
+{
+	struct devfreq *devfreq;
+
+	if (!dev)
+		return -EINVAL;
+
+	mutex_lock(&devfreq_list_lock);
+	devfreq = find_device_devfreq(dev);
+	if (IS_ERR(devfreq)) {
+		dev_err(dev, "%s: Unable to find devfreq entry for the device.\n",
+			__func__);
+		mutex_unlock(&devfreq_list_lock);
+		return -EINVAL;
+	}
+
+	list_del(&devfreq->node);
+
+	kfree(devfreq);
+
+	mutex_unlock(&devfreq_list_lock);
+
+	return 0;
+}
+
+/**
+ * devfreq_update() - Notify that the device OPP has been changed.
+ * @dev:	the device whose OPP has been changed.
+ */
+int devfreq_update(struct device *dev)
+{
+	struct devfreq *devfreq;
+	int err = 0;
+
+	mutex_lock(&devfreq_list_lock);
+
+	devfreq = find_device_devfreq(dev);
+	if (IS_ERR(devfreq)) {
+		err = PTR_ERR(devfreq);
+		goto out;
+	}
+
+	/* Reevaluate the proper frequency */
+	err = devfreq_do(devfreq);
+
+out:
+	mutex_unlock(&devfreq_list_lock);
+	return err;
+}
+
+/**
+ * devfreq_init() - Initialize data structure for devfreq framework and
+ *		  start polling registered devfreq devices.
+ */
+static int __init devfreq_init(void)
+{
+	devfreq_interval = jiffies_to_msecs(msecs_to_jiffies(devfreq_interval));
+	if (devfreq_interval <= 0) {
+		pr_err("DEVFREQ: devfreq_interval too small.\n");
+		return -EINVAL;
+	}
+
+	mutex_lock(&devfreq_list_lock);
+	polling = false;
+	devfreq_wq = create_freezable_workqueue("devfreq_wq");
+	INIT_DELAYED_WORK_DEFERRABLE(&devfreq_work, devfreq_monitor);
+	mutex_unlock(&devfreq_list_lock);
+
+	last_polled_at = ktime_get();
+	devfreq_monitor(&devfreq_work.work);
+	return 0;
+}
+late_initcall(devfreq_init);
diff --git a/drivers/base/power/opp.c b/drivers/base/power/opp.c
index 56a6899..819c1b3 100644
--- a/drivers/base/power/opp.c
+++ b/drivers/base/power/opp.c
@@ -21,6 +21,7 @@
 #include <linux/rculist.h>
 #include <linux/rcupdate.h>
 #include <linux/opp.h>
+#include <linux/devfreq.h>
 
 /*
  * Internal data structure organization with the OPP layer library is as
@@ -428,6 +429,11 @@ int opp_add(struct device *dev, unsigned long freq, unsigned long u_volt)
 	list_add_rcu(&new_opp->node, head);
 	mutex_unlock(&dev_opp_list_lock);
 
+	/*
+	 * Notify generic dvfs for the change and ignore error
+	 * because the device may not have a devfreq entry
+	 */
+	devfreq_update(dev);
 	return 0;
 }
 
@@ -512,6 +518,9 @@ unlock:
 	mutex_unlock(&dev_opp_list_lock);
 out:
 	kfree(new_opp);
+
+	/* Notify generic dvfs for the change and ignore error */
+	devfreq_update(dev);
 	return r;
 }
 
diff --git a/include/linux/devfreq.h b/include/linux/devfreq.h
new file mode 100644
index 0000000..6ec630b
--- /dev/null
+++ b/include/linux/devfreq.h
@@ -0,0 +1,103 @@
+/*
+ * devfreq: Generic Dynamic Voltage and Frequency Scaling (DVFS) Framework
+ *	    for Non-CPU Devices Based on OPP.
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *	MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __LINUX_DEVFREQ_H__
+#define __LINUX_DEVFREQ_H__
+
+#define DEVFREQ_NAME_LEN 16
+
+struct devfreq;
+struct devfreq_dev_status {
+	/* both since the last measure */
+	unsigned long total_time;
+	unsigned long busy_time;
+	unsigned long current_frequency;
+};
+
+struct devfreq_dev_profile {
+	unsigned long max_freq; /* may be larger than the actual value */
+	unsigned long initial_freq;
+	int polling_ms;	/* 0 for at opp change only */
+
+	int (*target)(struct device *dev, struct opp *opp);
+	int (*get_dev_status)(struct device *dev,
+			      struct devfreq_dev_status *stat);
+};
+
+/**
+ * struct devfreq_governor - Devfreq policy governor
+ * @name		Governor's name
+ * @get_target_freq	Returns desired operating frequency for the device.
+ *			Basically, get_target_freq will run
+ *			devfreq_dev_profile.get_dev_status() to get the
+ *			status of the device (load = busy_time / total_time).
+ */
+struct devfreq_governor {
+	char name[DEVFREQ_NAME_LEN];
+	int (*get_target_freq)(struct devfreq *this, unsigned long *freq);
+};
+
+/**
+ * struct devfreq - Device devfreq structure
+ * @node	list node - contains the devices with devfreq that have been
+ *		registered.
+ * @dev		device pointer
+ * @profile	device-specific devfreq profile
+ * @governor	method how to choose frequency based on the usage.
+ * @previous_freq	previously configured frequency value.
+ * @next_polling	the number of remaining "devfreq_monitor" executions to
+ *			reevaluate frequency/voltage of the device. Set by
+ *			profile's polling_ms interval.
+ * @data	Private data of the governor. The devfreq framework does not
+ *		touch this.
+ *
+ * This structure stores the devfreq information for a give device.
+ */
+struct devfreq {
+	struct list_head node;
+
+	struct device *dev;
+	struct devfreq_dev_profile *profile;
+	struct devfreq_governor *governor;
+
+	unsigned long previous_freq;
+	unsigned int next_polling;
+
+	void *data; /* private data for governors */
+};
+
+#if defined(CONFIG_PM_DEVFREQ)
+extern int devfreq_add_device(struct device *dev,
+			   struct devfreq_dev_profile *profile,
+			   struct devfreq_governor *governor);
+extern int devfreq_remove_device(struct device *dev);
+extern int devfreq_update(struct device *dev);
+#else /* !CONFIG_PM_DEVFREQ */
+static int devfreq_add_device(struct device *dev,
+			   struct devfreq_dev_profile *profile,
+			   struct devfreq_governor *governor)
+{
+	return 0;
+}
+
+static int devfreq_remove_device(struct device *dev)
+{
+	return 0;
+}
+
+static int devfreq_update(struct device *dev)
+{
+	return 0;
+}
+#endif /* CONFIG_PM_DEVFREQ */
+
+#endif /* __LINUX_DEVFREQ_H__ */
diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig
index 87f4d24..b7e15c8 100644
--- a/kernel/power/Kconfig
+++ b/kernel/power/Kconfig
@@ -227,3 +227,37 @@ config PM_OPP
 config PM_RUNTIME_CLK
 	def_bool y
 	depends on PM_RUNTIME && HAVE_CLK
+
+config ARCH_HAS_DEVFREQ
+	bool
+	depends on ARCH_HAS_OPP
+	help
+	  Denotes that the architecture supports DEVFREQ. If the architecture
+	  supports multiple OPP entries per device and the frequency of the
+	  devices with OPPs may be altered dynamically, the architecture
+	  supports DEVFREQ.
+
+config PM_DEVFREQ
+	bool "Generic Dynamic Voltage and Frequency Scaling (DVFS) Framework"
+	depends on PM_OPP && ARCH_HAS_DEVFREQ
+	help
+	  With OPP support, a device may have a list of frequencies and
+	  voltages available. DEVFREQ, a generic DVFS framework can be
+	  registered for a device with OPP support in order to let the
+	  governor provided to DEVFREQ choose an operating frequency
+	  based on the OPP's list and the policy given with DEVFREQ.
+
+	  Each device may have its own governor and policy. DEVFREQ can
+	  reevaluate the device state periodically and/or based on the
+	  OPP list changes (each frequency/voltage pair in OPP may be
+	  disabled or enabled).
+
+	  Like some CPUs with CPUFREQ, a device may have multiple clocks.
+	  However, because the clock frequencies of a single device are
+	  determined by the single device's state, an instance of DEVFREQ
+	  is attached to a single device and returns a "representative"
+	  clock frequency from the OPP of the device, which is also attached
+	  to a device by 1-to-1. The device registering DEVFREQ takes the
+	  responsiblity to "interpret" the frequency listed in OPP and
+	  to set its every clock accordingly with the "target" callback
+	  given to DEVFREQ.
-- 
1.7.4.1