From: Bryan DE FARIA <bdefaria@adeneo-embedded.com>
To: tony@atomide.com
Cc: Bryan DE FARIA <bdefaria@adeneo-embedded.com>,
linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4] OMAP3EVM: ehci: Fix EHCI support
Date: Thu, 25 Aug 2011 11:22:49 +0200 [thread overview]
Message-ID: <1314264169-32514-1-git-send-email-bdefaria@adeneo-embedded.com> (raw)
Set the VAUX2 regulator supply to 1.8V for the HSUSB host interface.
Tps65950 GPIO2 has to be set to zero in order to enable the EHCI select line.
Signed-off-by: Bryan DE FARIA <bdefaria@adeneo-embedded.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 25 +++++++++++++++++++++++++
1 files changed, 25 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index c452b3f..d9e0f10 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -377,6 +377,10 @@ static int omap3evm_twl_gpio_setup(struct device *dev,
if (r)
printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
+ /* gpio + 2 == EHCI, camera and audio lines on motherboard Enable*/
+ if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+ gpio_request_one(gpio + 2, GPIOF_OUT_INIT_LOW, "EN_MB_LINES");
+
/* gpio + 7 == DVI Enable */
gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
@@ -450,6 +454,25 @@ static struct regulator_init_data omap3evm_vio = {
.consumer_supplies = omap3evm_vio_supply,
};
+/* VAUX2 for EHCI */
+static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
+ REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+};
+
+static struct regulator_init_data omap3evm_vaux2 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(omap3evm_vaux2_supplies),
+ .consumer_supplies = omap3evm_vaux2_supplies,
+};
+
#ifdef CONFIG_WL12XX_PLATFORM_DATA
#define OMAP3EVM_WLAN_PMENA_GPIO (150)
@@ -510,6 +533,8 @@ static int __init omap3_evm_i2c_init(void)
omap3evm_twldata.vdac->constraints.apply_uV = true;
omap3evm_twldata.vpll2->constraints.apply_uV = true;
+ if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+ omap3evm_twldata.vaux2 = &omap3evm_vaux2;
omap3_pmic_init("twl4030", &omap3evm_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
--
1.7.4.1
WARNING: multiple messages have this Message-ID (diff)
From: bdefaria@adeneo-embedded.com (Bryan DE FARIA)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4] OMAP3EVM: ehci: Fix EHCI support
Date: Thu, 25 Aug 2011 11:22:49 +0200 [thread overview]
Message-ID: <1314264169-32514-1-git-send-email-bdefaria@adeneo-embedded.com> (raw)
Set the VAUX2 regulator supply to 1.8V for the HSUSB host interface.
Tps65950 GPIO2 has to be set to zero in order to enable the EHCI select line.
Signed-off-by: Bryan DE FARIA <bdefaria@adeneo-embedded.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 25 +++++++++++++++++++++++++
1 files changed, 25 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index c452b3f..d9e0f10 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -377,6 +377,10 @@ static int omap3evm_twl_gpio_setup(struct device *dev,
if (r)
printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
+ /* gpio + 2 == EHCI, camera and audio lines on motherboard Enable*/
+ if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+ gpio_request_one(gpio + 2, GPIOF_OUT_INIT_LOW, "EN_MB_LINES");
+
/* gpio + 7 == DVI Enable */
gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
@@ -450,6 +454,25 @@ static struct regulator_init_data omap3evm_vio = {
.consumer_supplies = omap3evm_vio_supply,
};
+/* VAUX2 for EHCI */
+static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
+ REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+};
+
+static struct regulator_init_data omap3evm_vaux2 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(omap3evm_vaux2_supplies),
+ .consumer_supplies = omap3evm_vaux2_supplies,
+};
+
#ifdef CONFIG_WL12XX_PLATFORM_DATA
#define OMAP3EVM_WLAN_PMENA_GPIO (150)
@@ -510,6 +533,8 @@ static int __init omap3_evm_i2c_init(void)
omap3evm_twldata.vdac->constraints.apply_uV = true;
omap3evm_twldata.vpll2->constraints.apply_uV = true;
+ if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+ omap3evm_twldata.vaux2 = &omap3evm_vaux2;
omap3_pmic_init("twl4030", &omap3evm_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
--
1.7.4.1
next reply other threads:[~2011-08-25 9:23 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-25 9:22 Bryan DE FARIA [this message]
2011-08-25 9:22 ` [PATCH v4] OMAP3EVM: ehci: Fix EHCI support Bryan DE FARIA
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1314264169-32514-1-git-send-email-bdefaria@adeneo-embedded.com \
--to=bdefaria@adeneo-embedded.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.