[PATCH v12 1/3] MTD : add the common code for GPMI-NAND controller driver

[Huang Shijie <b32955@freescale.com>]

These files contain the common code for the GPMI-NAND driver.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
---
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 1619 ++++++++++++++++++++++++++++++++
 drivers/mtd/nand/gpmi-nand/gpmi-nand.h |  273 ++++++
 2 files changed, 1892 insertions(+), 0 deletions(-)
 create mode 100644 drivers/mtd/nand/gpmi-nand/gpmi-nand.c
 create mode 100644 drivers/mtd/nand/gpmi-nand/gpmi-nand.h

diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
new file mode 100644
index 0000000..5c0fe0d
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
@@ -0,0 +1,1619 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/gpmi-nand.h>
+#include <linux/mtd/partitions.h>
+
+#include "gpmi-nand.h"
+
+/* add our owner bbt descriptor */
+static uint8_t scan_ff_pattern[] = { 0xff };
+static struct nand_bbt_descr gpmi_bbt_descr = {
+	.options	= 0,
+	.offs		= 0,
+	.len		= 1,
+	.pattern	= scan_ff_pattern
+};
+
+/*  We will use all the (page + OOB). */
+static struct nand_ecclayout gpmi_hw_ecclayout = {
+	.eccbytes = 0,
+	.eccpos = { 0, },
+	.oobfree = { {.offset = 0, .length = 0} }
+};
+
+static irqreturn_t bch_irq(int irq, void *cookie)
+{
+	struct gpmi_nand_data *this = cookie;
+
+	gpmi_clear_bch(this);
+	complete(&this->bch_done);
+	return IRQ_HANDLED;
+}
+
+/*
+ *  Calculate the ECC strength by hand:
+ *	E : The ECC strength.
+ *	G : the length of Galois Field.
+ *	N : The chunk count of per page.
+ *	O : the oobsize of the NAND chip.
+ *	M : the metasize of per page.
+ *
+ *	The formula is :
+ *		E * G * N
+ *	      ------------ <= (O - M)
+ *                  8
+ *
+ *      So, we get E by:
+ *                    (O - M) * 8
+ *              E <= -------------
+ *                       G * N
+ */
+static inline int get_ecc_strength(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	struct mtd_info	*mtd = &this->mtd;
+	int ecc_strength;
+
+	ecc_strength = ((mtd->oobsize - geo->metadata_size) * 8)
+			/ (geo->gf_len * geo->ecc_chunk_count);
+
+	/* We need the minor even number. */
+	return round_down(ecc_strength, 2);
+}
+
+int common_nfc_set_geometry(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	struct mtd_info *mtd = &this->mtd;
+	unsigned int metadata_size;
+	unsigned int status_size;
+	unsigned int block_mark_bit_offset;
+
+	/*
+	 * The size of the metadata can be changed, though we set it to 10
+	 * bytes now. But it can't be too large, because we have to save
+	 * enough space for BCH.
+	 */
+	geo->metadata_size = 10;
+
+	/* The default for the length of Galois Field. */
+	geo->gf_len = 13;
+
+	/* The default for chunk size. There is no oobsize greater then 512. */
+	geo->ecc_chunk_size = 512;
+	while (geo->ecc_chunk_size < mtd->oobsize)
+		geo->ecc_chunk_size *= 2; /* keep C >= O */
+
+	geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size;
+
+	/* We use the same ECC strength for all chunks. */
+	geo->ecc_strength = get_ecc_strength(this);
+	if (!geo->ecc_strength) {
+		pr_err("We get a wrong ECC strength.\n");
+		return -EINVAL;
+	}
+
+	geo->page_size = mtd->writesize + mtd->oobsize;
+	geo->payload_size = mtd->writesize;
+
+	/*
+	 * The auxiliary buffer contains the metadata and the ECC status. The
+	 * metadata is padded to the nearest 32-bit boundary. The ECC status
+	 * contains one byte for every ECC chunk, and is also padded to the
+	 * nearest 32-bit boundary.
+	 */
+	metadata_size = ALIGN(geo->metadata_size, 4);
+	status_size   = ALIGN(geo->ecc_chunk_count, 4);
+
+	geo->auxiliary_size = metadata_size + status_size;
+	geo->auxiliary_status_offset = metadata_size;
+
+	if (!this->swap_block_mark)
+		return 0;
+
+	/*
+	 * We need to compute the byte and bit offsets of
+	 * the physical block mark within the ECC-based view of the page.
+	 *
+	 * NAND chip with 2K page shows below:
+	 *                                             (Block Mark)
+	 *                                                   |      |
+	 *                                                   |  D   |
+	 *                                                   |<---->|
+	 *                                                   V      V
+	 *    +---+----------+-+----------+-+----------+-+----------+-+
+	 *    | M |   data   |E|   data   |E|   data   |E|   data   |E|
+	 *    +---+----------+-+----------+-+----------+-+----------+-+
+	 *
+	 * The position of block mark moves forward in the ECC-based view
+	 * of page, and the delta is:
+	 *
+	 *                   E * G * (N - 1)
+	 *             D = (---------------- + M)
+	 *                          8
+	 *
+	 * With the formula to compute the ECC strength, and the condition
+	 *       : C >= O         (C is the ecc chunk size)
+	 *
+	 * It's easy to deduce to the following result:
+	 *
+	 *         E * G       (O - M)      C - M         C - M
+	 *      ----------- <= ------- <=  --------  <  ---------
+	 *           8            N           N          (N - 1)
+	 *
+	 *  So, we get:
+	 *
+	 *                   E * G * (N - 1)
+	 *             D = (---------------- + M) < C
+	 *                          8
+	 *
+	 *  The above inequality means the position of block mark
+	 *  within the ECC-based view of the page is still in the data chunk,
+	 *  and it's NOT in the ECC bits of the chunk.
+	 *
+	 *  Use the following to compute the bit position of the
+	 *  physical block mark within the ECC-based view of the page:
+	 *          (page_size - D) * 8
+	 *
+	 *  --Huang Shijie
+	 */
+	block_mark_bit_offset = mtd->writesize * 8 -
+		(geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1)
+				+ geo->metadata_size * 8);
+
+	geo->block_mark_byte_offset = block_mark_bit_offset / 8;
+	geo->block_mark_bit_offset  = block_mark_bit_offset % 8;
+	return 0;
+}
+
+struct dma_chan *get_dma_chan(struct gpmi_nand_data *this)
+{
+	int chipnr = this->current_chip;
+
+	return this->dma_chans[chipnr];
+}
+
+/* Can we use the upper's buffer directly for DMA? */
+void prepare_data_dma(struct gpmi_nand_data *this, enum dma_data_direction dr)
+{
+	struct scatterlist *sgl = &this->data_sgl;
+	int ret;
+
+	this->direct_dma_map_ok = true;
+
+	/* first try to map the upper buffer directly */
+	sg_init_one(sgl, this->upper_buf, this->upper_len);
+	ret = dma_map_sg(this->dev, sgl, 1, dr);
+	if (ret == 0) {
+		/* We have to use our own DMA buffer. */
+		sg_init_one(sgl, this->data_buffer_dma, PAGE_SIZE);
+
+		if (dr == DMA_TO_DEVICE)
+			memcpy(this->data_buffer_dma, this->upper_buf,
+				this->upper_len);
+
+		ret = dma_map_sg(this->dev, sgl, 1, dr);
+		if (ret == 0)
+			pr_err("map failed.\n");
+
+		this->direct_dma_map_ok = false;
+	}
+}
+
+/* This will be called after the DMA operation is finished. */
+static void dma_irq_callback(void *param)
+{
+	struct gpmi_nand_data *this = param;
+	struct completion *dma_c = &this->dma_done;
+
+	complete(dma_c);
+
+	switch (this->dma_type) {
+	case DMA_FOR_COMMAND:
+		dma_unmap_sg(this->dev, &this->cmd_sgl, 1, DMA_TO_DEVICE);
+		break;
+
+	case DMA_FOR_READ_DATA:
+		dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE);
+		if (this->direct_dma_map_ok == false)
+			memcpy(this->upper_buf, this->data_buffer_dma,
+				this->upper_len);
+		break;
+
+	case DMA_FOR_WRITE_DATA:
+		dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE);
+		break;
+
+	case DMA_FOR_READ_ECC_PAGE:
+	case DMA_FOR_WRITE_ECC_PAGE:
+		/* We have to wait the BCH interrupt to finish. */
+		break;
+
+	default:
+		pr_err("in wrong DMA operation.\n");
+	}
+}
+
+int start_dma_without_bch_irq(struct gpmi_nand_data *this,
+				struct dma_async_tx_descriptor *desc)
+{
+	struct completion *dma_c = &this->dma_done;
+	int err;
+
+	init_completion(dma_c);
+
+	desc->callback		= dma_irq_callback;
+	desc->callback_param	= this;
+	dmaengine_submit(desc);
+
+	/* Wait for the interrupt from the DMA block. */
+	err = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000));
+	if (!err) {
+		pr_err("DMA timeout, last DMA :%d\n", this->last_dma_type);
+		gpmi_dump_info(this);
+		return -ETIMEDOUT;
+	}
+	return 0;
+}
+
+/*
+ * This function is used in BCH reading or BCH writing pages.
+ * It will wait for the BCH interrupt as long as ONE second.
+ * Actually, we must wait for two interrupts :
+ *	[1] firstly the DMA interrupt and
+ *	[2] secondly the BCH interrupt.
+ */
+int start_dma_with_bch_irq(struct gpmi_nand_data *this,
+			struct dma_async_tx_descriptor *desc)
+{
+	struct completion *bch_c = &this->bch_done;
+	int err;
+
+	/* Prepare to receive an interrupt from the BCH block. */
+	init_completion(bch_c);
+
+	/* start the DMA */
+	start_dma_without_bch_irq(this, desc);
+
+	/* Wait for the interrupt from the BCH block. */
+	err = wait_for_completion_timeout(bch_c, msecs_to_jiffies(1000));
+	if (!err) {
+		pr_err("BCH timeout, last DMA :%d\n", this->last_dma_type);
+		gpmi_dump_info(this);
+		return -ETIMEDOUT;
+	}
+	return 0;
+}
+
+static int __devinit
+acquire_register_block(struct gpmi_nand_data *this, const char *res_name)
+{
+	struct platform_device *pdev = this->pdev;
+	struct resources *res = &this->resources;
+	struct resource *r;
+	void *p;
+
+	r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name);
+	if (!r) {
+		pr_err("Can't get resource for %s\n", res_name);
+		return -ENXIO;
+	}
+
+	p = ioremap(r->start, resource_size(r));
+	if (!p) {
+		pr_err("Can't remap %s\n", res_name);
+		return -ENOMEM;
+	}
+
+	if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME))
+		res->gpmi_regs = p;
+	else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME))
+		res->bch_regs = p;
+	else
+		pr_err("unknown resource name : %s\n", res_name);
+
+	return 0;
+}
+
+static void release_register_block(struct gpmi_nand_data *this)
+{
+	struct resources *res = &this->resources;
+	if (res->gpmi_regs)
+		iounmap(res->gpmi_regs);
+	if (res->bch_regs)
+		iounmap(res->bch_regs);
+	res->gpmi_regs = NULL;
+	res->bch_regs = NULL;
+}
+
+static int __devinit
+acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h)
+{
+	struct platform_device *pdev = this->pdev;
+	struct resources *res = &this->resources;
+	const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME;
+	struct resource *r;
+	int err;
+
+	r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name);
+	if (!r) {
+		pr_err("Can't get resource for %s\n", res_name);
+		return -ENXIO;
+	}
+
+	err = request_irq(r->start, irq_h, 0, res_name, this);
+	if (err) {
+		pr_err("Can't own %s\n", res_name);
+		return err;
+	}
+
+	res->bch_low_interrupt = r->start;
+	res->bch_high_interrupt = r->end;
+	return 0;
+}
+
+static void release_bch_irq(struct gpmi_nand_data *this)
+{
+	struct resources *res = &this->resources;
+	int i = res->bch_low_interrupt;
+
+	for (; i <= res->bch_high_interrupt; i++)
+		free_irq(i, this);
+}
+
+static bool gpmi_dma_filter(struct dma_chan *chan, void *param)
+{
+	struct gpmi_nand_data *this = param;
+	struct resource *r = this->private;
+
+	if (!mxs_dma_is_apbh(chan))
+		return false;
+	/*
+	 * only catch the GPMI dma channels :
+	 *	for mx23 :	MX23_DMA_GPMI0 ~ MX23_DMA_GPMI3
+	 *		(These four channels share the same IRQ!)
+	 *
+	 *	for mx28 :	MX28_DMA_GPMI0 ~ MX28_DMA_GPMI7
+	 *		(These eight channels share the same IRQ!)
+	 */
+	if (r->start <= chan->chan_id && chan->chan_id <= r->end) {
+		chan->private = &this->dma_data;
+		return true;
+	}
+	return false;
+}
+
+static void release_dma_channels(struct gpmi_nand_data *this)
+{
+	unsigned int i;
+	for (i = 0; i < DMA_CHANS; i++)
+		if (this->dma_chans[i]) {
+			dma_release_channel(this->dma_chans[i]);
+			this->dma_chans[i] = NULL;
+		}
+}
+
+static int __devinit acquire_dma_channels(struct gpmi_nand_data *this)
+{
+	struct platform_device *pdev = this->pdev;
+	struct gpmi_nand_platform_data *pdata = this->pdata;
+	struct resources *res = &this->resources;
+	struct resource *r, *r_dma;
+	unsigned int i;
+
+	r = platform_get_resource_byname(pdev, IORESOURCE_DMA,
+					GPMI_NAND_DMA_CHANNELS_RES_NAME);
+	r_dma = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
+					GPMI_NAND_DMA_INTERRUPT_RES_NAME);
+	if (!r || !r_dma) {
+		pr_err("Can't get resource for DMA\n");
+		return -ENXIO;
+	}
+
+	/* used in gpmi_dma_filter() */
+	this->private = r;
+
+	for (i = r->start; i <= r->end; i++) {
+		struct dma_chan *dma_chan;
+		dma_cap_mask_t mask;
+
+		if (i - r->start >= pdata->max_chip_count)
+			break;
+
+		dma_cap_zero(mask);
+		dma_cap_set(DMA_SLAVE, mask);
+
+		/* get the DMA interrupt */
+		if (r_dma->start == r_dma->end) {
+			/* only register the first. */
+			if (i == r->start)
+				this->dma_data.chan_irq = r_dma->start;
+			else
+				this->dma_data.chan_irq = NO_IRQ;
+		} else
+			this->dma_data.chan_irq = r_dma->start + (i - r->start);
+
+		dma_chan = dma_request_channel(mask, gpmi_dma_filter, this);
+		if (!dma_chan)
+			goto acquire_err;
+
+		/* fill the first empty item */
+		this->dma_chans[i - r->start] = dma_chan;
+	}
+
+	res->dma_low_channel = r->start;
+	res->dma_high_channel = i;
+	return 0;
+
+acquire_err:
+	pr_err("Can't acquire DMA channel %u\n", i);
+	release_dma_channels(this);
+	return -EINVAL;
+}
+
+static int __devinit acquire_resources(struct gpmi_nand_data *this)
+{
+	struct resources *res = &this->resources;
+	int ret;
+
+	ret = acquire_register_block(this, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME);
+	if (ret)
+		goto exit_regs;
+
+	ret = acquire_register_block(this, GPMI_NAND_BCH_REGS_ADDR_RES_NAME);
+	if (ret)
+		goto exit_regs;
+
+	ret = acquire_bch_irq(this, bch_irq);
+	if (ret)
+		goto exit_regs;
+
+	ret = acquire_dma_channels(this);
+	if (ret)
+		goto exit_dma_channels;
+
+	res->clock = clk_get(&this->pdev->dev, NULL);
+	if (IS_ERR(res->clock)) {
+		pr_err("can not get the clock\n");
+		ret = -ENOENT;
+		goto exit_clock;
+	}
+	return 0;
+
+exit_clock:
+	release_dma_channels(this);
+exit_dma_channels:
+	release_bch_irq(this);
+exit_regs:
+	release_register_block(this);
+	return ret;
+}
+
+static void release_resources(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+
+	clk_put(r->clock);
+	release_register_block(this);
+	release_bch_irq(this);
+	release_dma_channels(this);
+}
+
+static int __devinit init_hardware(struct gpmi_nand_data *this)
+{
+	int ret;
+
+	/*
+	 * This structure contains the "safe" GPMI timing that should succeed
+	 * with any NAND Flash device
+	 * (although, with less-than-optimal performance).
+	 */
+	struct nand_timing  safe_timing = {
+		.data_setup_in_ns        = 80,
+		.data_hold_in_ns         = 60,
+		.address_setup_in_ns     = 25,
+		.gpmi_sample_delay_in_ns =  6,
+		.tREA_in_ns              = -1,
+		.tRLOH_in_ns             = -1,
+		.tRHOH_in_ns             = -1,
+	};
+
+	/* Initialize the hardwares. */
+	ret = gpmi_init(this);
+	if (ret)
+		return ret;
+
+	this->timing = safe_timing;
+	return 0;
+}
+
+static int read_page_prepare(struct gpmi_nand_data *this,
+			void *destination, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			void **use_virt, dma_addr_t *use_phys)
+{
+	struct device *dev = this->dev;
+
+	if (virt_addr_valid(destination)) {
+		dma_addr_t dest_phys;
+
+		dest_phys = dma_map_single(dev, destination,
+						length, DMA_FROM_DEVICE);
+		if (dma_mapping_error(dev, dest_phys)) {
+			if (alt_size < length) {
+				pr_err("Alternate buffer is too small\n");
+				return -ENOMEM;
+			}
+			goto map_failed;
+		}
+		*use_virt = destination;
+		*use_phys = dest_phys;
+		this->direct_dma_map_ok = true;
+		return 0;
+	}
+
+map_failed:
+	*use_virt = alt_virt;
+	*use_phys = alt_phys;
+	this->direct_dma_map_ok = false;
+	return 0;
+}
+
+static inline void read_page_end(struct gpmi_nand_data *this,
+			void *destination, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			void *used_virt, dma_addr_t used_phys)
+{
+	if (this->direct_dma_map_ok)
+		dma_unmap_single(this->dev, used_phys, length, DMA_FROM_DEVICE);
+}
+
+static inline void read_page_swap_end(struct gpmi_nand_data *this,
+			void *destination, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			void *used_virt, dma_addr_t used_phys)
+{
+	if (!this->direct_dma_map_ok)
+		memcpy(destination, alt_virt, length);
+}
+
+static int send_page_prepare(struct gpmi_nand_data *this,
+			const void *source, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			const void **use_virt, dma_addr_t *use_phys)
+{
+	struct device *dev = this->dev;
+
+	if (virt_addr_valid(source)) {
+		dma_addr_t source_phys;
+
+		source_phys = dma_map_single(dev, (void *)source, length,
+						DMA_TO_DEVICE);
+		if (dma_mapping_error(dev, source_phys)) {
+			if (alt_size < length) {
+				pr_err("Alternate buffer is too small\n");
+				return -ENOMEM;
+			}
+			goto map_failed;
+		}
+		*use_virt = source;
+		*use_phys = source_phys;
+		return 0;
+	}
+map_failed:
+	/*
+	 * Copy the content of the source buffer into the alternate
+	 * buffer and set up the return values accordingly.
+	 */
+	memcpy(alt_virt, source, length);
+
+	*use_virt = alt_virt;
+	*use_phys = alt_phys;
+	return 0;
+}
+
+static void send_page_end(struct gpmi_nand_data *this,
+			const void *source, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			const void *used_virt, dma_addr_t used_phys)
+{
+	struct device *dev = this->dev;
+	if (used_virt == source)
+		dma_unmap_single(dev, used_phys, length, DMA_TO_DEVICE);
+}
+
+static void gpmi_free_dma_buffer(struct gpmi_nand_data *this)
+{
+	struct device *dev = this->dev;
+
+	if (this->page_buffer_virt && virt_addr_valid(this->page_buffer_virt))
+		dma_free_coherent(dev, this->page_buffer_size,
+					this->page_buffer_virt,
+					this->page_buffer_phys);
+	kfree(this->cmd_buffer);
+	kfree(this->data_buffer_dma);
+
+	this->cmd_buffer	= NULL;
+	this->data_buffer_dma	= NULL;
+	this->page_buffer_virt	= NULL;
+	this->page_buffer_size	=  0;
+}
+
+/* Allocate the DMA buffers */
+static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	struct device *dev = this->dev;
+
+	/* [1] Allocate a command buffer. PAGE_SIZE is enough. */
+	this->cmd_buffer = kzalloc(PAGE_SIZE, GFP_DMA);
+	if (this->cmd_buffer == NULL)
+		goto error_alloc;
+
+	/* [2] Allocate a read/write data buffer. PAGE_SIZE is enough. */
+	this->data_buffer_dma = kzalloc(PAGE_SIZE, GFP_DMA);
+	if (this->data_buffer_dma == NULL)
+		goto error_alloc;
+
+	/*
+	 * [3] Allocate the page buffer.
+	 *
+	 * Both the payload buffer and the auxiliary buffer must appear on
+	 * 32-bit boundaries. We presume the size of the payload buffer is a
+	 * power of two and is much larger than four, which guarantees the
+	 * auxiliary buffer will appear on a 32-bit boundary.
+	 */
+	this->page_buffer_size = geo->payload_size + geo->auxiliary_size;
+	this->page_buffer_virt = dma_alloc_coherent(dev, this->page_buffer_size,
+					&this->page_buffer_phys, GFP_DMA);
+	if (!this->page_buffer_virt)
+		goto error_alloc;
+
+
+	/* Slice up the page buffer. */
+	this->payload_virt = this->page_buffer_virt;
+	this->payload_phys = this->page_buffer_phys;
+	this->auxiliary_virt = this->payload_virt + geo->payload_size;
+	this->auxiliary_phys = this->payload_phys + geo->payload_size;
+	return 0;
+
+error_alloc:
+	gpmi_free_dma_buffer(this);
+	pr_err("allocate DMA buffer ret!!\n");
+	return -ENOMEM;
+}
+
+static void gpmi_cmd_ctrl(struct mtd_info *mtd, int data, unsigned int ctrl)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	int ret;
+
+	/*
+	 * Every operation begins with a command byte and a series of zero or
+	 * more address bytes. These are distinguished by either the Address
+	 * Latch Enable (ALE) or Command Latch Enable (CLE) signals being
+	 * asserted. When MTD is ready to execute the command, it will deassert
+	 * both latch enables.
+	 *
+	 * Rather than run a separate DMA operation for every single byte, we
+	 * queue them up and run a single DMA operation for the entire series
+	 * of command and data bytes. NAND_CMD_NONE means the END of the queue.
+	 */
+	if ((ctrl & (NAND_ALE | NAND_CLE))) {
+		if (data != NAND_CMD_NONE)
+			this->cmd_buffer[this->command_length++] = data;
+		return;
+	}
+
+	if (!this->command_length)
+		return;
+
+	ret = gpmi_send_command(this);
+	if (ret)
+		pr_err("Chip: %u, Error %d\n", this->current_chip, ret);
+
+	this->command_length = 0;
+}
+
+static int gpmi_dev_ready(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	return gpmi_is_ready(this, this->current_chip);
+}
+
+static void gpmi_select_chip(struct mtd_info *mtd, int chipnr)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	if ((this->current_chip < 0) && (chipnr >= 0))
+		gpmi_begin(this);
+	else if ((this->current_chip >= 0) && (chipnr < 0))
+		gpmi_end(this);
+
+	this->current_chip = chipnr;
+}
+
+static void gpmi_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	pr_debug("len is %d\n", len);
+	this->upper_buf	= buf;
+	this->upper_len	= len;
+
+	gpmi_read_data(this);
+}
+
+static void gpmi_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	pr_debug("len is %d\n", len);
+	this->upper_buf	= (uint8_t *)buf;
+	this->upper_len	= len;
+
+	gpmi_send_data(this);
+}
+
+static uint8_t gpmi_read_byte(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	uint8_t *buf = this->data_buffer_dma;
+
+	gpmi_read_buf(mtd, buf, 1);
+	return buf[0];
+}
+
+/*
+ * Handles block mark swapping.
+ * It can be called in swapping the block mark, or swapping it back,
+ * because the the operations are the same.
+ */
+static void block_mark_swapping(struct gpmi_nand_data *this,
+				void *payload, void *auxiliary)
+{
+	struct bch_geometry *nfc_geo = &this->bch_geometry;
+	unsigned char *p;
+	unsigned char *a;
+	unsigned int  bit;
+	unsigned char mask;
+	unsigned char from_data;
+	unsigned char from_oob;
+
+	if (!this->swap_block_mark)
+		return;
+
+	/*
+	 * If control arrives here, we're swapping. Make some convenience
+	 * variables.
+	 */
+	bit = nfc_geo->block_mark_bit_offset;
+	p   = payload + nfc_geo->block_mark_byte_offset;
+	a   = auxiliary;
+
+	/*
+	 * Get the byte from the data area that overlays the block mark. Since
+	 * the ECC engine applies its own view to the bits in the page, the
+	 * physical block mark won't (in general) appear on a byte boundary in
+	 * the data.
+	 */
+	from_data = (p[0] >> bit) | (p[1] << (8 - bit));
+
+	/* Get the byte from the OOB. */
+	from_oob = a[0];
+
+	/* Swap them. */
+	a[0] = from_data;
+
+	mask = (0x1 << bit) - 1;
+	p[0] = (p[0] & mask) | (from_oob << bit);
+
+	mask = ~0 << bit;
+	p[1] = (p[1] & mask) | (from_oob >> (8 - bit));
+}
+
+static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+				uint8_t *buf, int page)
+{
+	struct gpmi_nand_data *this = chip->priv;
+	struct bch_geometry *nfc_geo = &this->bch_geometry;
+	void          *payload_virt;
+	dma_addr_t    payload_phys;
+	void          *auxiliary_virt;
+	dma_addr_t    auxiliary_phys;
+	unsigned int  i;
+	unsigned char *status;
+	unsigned int  failed;
+	unsigned int  corrected;
+	int           ret;
+
+	pr_debug("page number is : %d\n", page);
+	ret = read_page_prepare(this, buf, mtd->writesize,
+					this->payload_virt, this->payload_phys,
+					nfc_geo->payload_size,
+					&payload_virt, &payload_phys);
+	if (ret) {
+		pr_err("Inadequate DMA buffer\n");
+		ret = -ENOMEM;
+		return ret;
+	}
+	auxiliary_virt = this->auxiliary_virt;
+	auxiliary_phys = this->auxiliary_phys;
+
+	/* go! */
+	ret = gpmi_read_page(this, payload_phys, auxiliary_phys);
+	read_page_end(this, buf, mtd->writesize,
+			this->payload_virt, this->payload_phys,
+			nfc_geo->payload_size,
+			payload_virt, payload_phys);
+	if (ret) {
+		pr_err("Error in ECC-based read: %d\n", ret);
+		goto exit_nfc;
+	}
+
+	/* handle the block mark swapping */
+	block_mark_swapping(this, payload_virt, auxiliary_virt);
+
+	/* Loop over status bytes, accumulating ECC status. */
+	failed		= 0;
+	corrected	= 0;
+	status		= auxiliary_virt + nfc_geo->auxiliary_status_offset;
+
+	for (i = 0; i < nfc_geo->ecc_chunk_count; i++, status++) {
+		if ((*status == STATUS_GOOD) || (*status == STATUS_ERASED))
+			continue;
+
+		if (*status == STATUS_UNCORRECTABLE) {
+			failed++;
+			continue;
+		}
+		corrected += *status;
+	}
+
+	/*
+	 * Propagate ECC status to the owning MTD only when failed or
+	 * corrected times nearly reaches our ECC correction threshold.
+	 */
+	if (failed || corrected >= (nfc_geo->ecc_strength - 1)) {
+		mtd->ecc_stats.failed    += failed;
+		mtd->ecc_stats.corrected += corrected;
+	}
+
+	/*
+	 * It's time to deliver the OOB bytes. See gpmi_ecc_read_oob() for
+	 * details about our policy for delivering the OOB.
+	 *
+	 * We fill the caller's buffer with set bits, and then copy the block
+	 * mark to th caller's buffer. Note that, if block mark swapping was
+	 * necessary, it has already been done, so we can rely on the first
+	 * byte of the auxiliary buffer to contain the block mark.
+	 */
+	memset(chip->oob_poi, ~0, mtd->oobsize);
+	chip->oob_poi[0] = ((uint8_t *) auxiliary_virt)[0];
+
+	read_page_swap_end(this, buf, mtd->writesize,
+			this->payload_virt, this->payload_phys,
+			nfc_geo->payload_size,
+			payload_virt, payload_phys);
+exit_nfc:
+	return ret;
+}
+
+static void gpmi_ecc_write_page(struct mtd_info *mtd,
+				struct nand_chip *chip, const uint8_t *buf)
+{
+	struct gpmi_nand_data *this = chip->priv;
+	struct bch_geometry *nfc_geo = &this->bch_geometry;
+	const void *payload_virt;
+	dma_addr_t payload_phys;
+	const void *auxiliary_virt;
+	dma_addr_t auxiliary_phys;
+	int        ret;
+
+	pr_debug("ecc write page.\n");
+	if (this->swap_block_mark) {
+		/*
+		 * If control arrives here, we're doing block mark swapping.
+		 * Since we can't modify the caller's buffers, we must copy them
+		 * into our own.
+		 */
+		memcpy(this->payload_virt, buf, mtd->writesize);
+		payload_virt = this->payload_virt;
+		payload_phys = this->payload_phys;
+
+		memcpy(this->auxiliary_virt, chip->oob_poi,
+				nfc_geo->auxiliary_size);
+		auxiliary_virt = this->auxiliary_virt;
+		auxiliary_phys = this->auxiliary_phys;
+
+		/* Handle block mark swapping. */
+		block_mark_swapping(this,
+				(void *) payload_virt, (void *) auxiliary_virt);
+	} else {
+		/*
+		 * If control arrives here, we're not doing block mark swapping,
+		 * so we can to try and use the caller's buffers.
+		 */
+		ret = send_page_prepare(this,
+				buf, mtd->writesize,
+				this->payload_virt, this->payload_phys,
+				nfc_geo->payload_size,
+				&payload_virt, &payload_phys);
+		if (ret) {
+			pr_err("Inadequate payload DMA buffer\n");
+			return;
+		}
+
+		ret = send_page_prepare(this,
+				chip->oob_poi, mtd->oobsize,
+				this->auxiliary_virt, this->auxiliary_phys,
+				nfc_geo->auxiliary_size,
+				&auxiliary_virt, &auxiliary_phys);
+		if (ret) {
+			pr_err("Inadequate auxiliary DMA buffer\n");
+			goto exit_auxiliary;
+		}
+	}
+
+	/* Ask the NFC. */
+	ret = gpmi_send_page(this, payload_phys, auxiliary_phys);
+	if (ret)
+		pr_err("Error in ECC-based write: %d\n", ret);
+
+	if (!this->swap_block_mark) {
+		send_page_end(this, chip->oob_poi, mtd->oobsize,
+				this->auxiliary_virt, this->auxiliary_phys,
+				nfc_geo->auxiliary_size,
+				auxiliary_virt, auxiliary_phys);
+exit_auxiliary:
+		send_page_end(this, buf, mtd->writesize,
+				this->payload_virt, this->payload_phys,
+				nfc_geo->payload_size,
+				payload_virt, payload_phys);
+	}
+}
+
+/*
+ * There are several places in this driver where we have to handle the OOB and
+ * block marks. This is the function where things are the most complicated, so
+ * this is where we try to explain it all. All the other places refer back to
+ * here.
+ *
+ * These are the rules, in order of decreasing importance:
+ *
+ * 1) Nothing the caller does can be allowed to imperil the block mark.
+ *
+ * 2) In read operations, the first byte of the OOB we return must reflect the
+ *    true state of the block mark, no matter where that block mark appears in
+ *    the physical page.
+ *
+ * 3) ECC-based read operations return an OOB full of set bits (since we never
+ *    allow ECC-based writes to the OOB, it doesn't matter what ECC-based reads
+ *    return).
+ *
+ * 4) "Raw" read operations return a direct view of the physical bytes in the
+ *    page, using the conventional definition of which bytes are data and which
+ *    are OOB. This gives the caller a way to see the actual, physical bytes
+ *    in the page, without the distortions applied by our ECC engine.
+ *
+ *
+ * What we do for this specific read operation depends on two questions:
+ *
+ * 1) Are we doing a "raw" read, or an ECC-based read?
+ *
+ * 2) Are we using block mark swapping or transcription?
+ *
+ * There are four cases, illustrated by the following Karnaugh map:
+ *
+ *                    |           Raw           |         ECC-based       |
+ *       -------------+-------------------------+-------------------------+
+ *                    | Read the conventional   |                         |
+ *                    | OOB at the end of the   |                         |
+ *       Swapping     | page and return it. It  |                         |
+ *                    | contains exactly what   |                         |
+ *                    | we want.                | Read the block mark and |
+ *       -------------+-------------------------+ return it in a buffer   |
+ *                    | Read the conventional   | full of set bits.       |
+ *                    | OOB at the end of the   |                         |
+ *                    | page and also the block |                         |
+ *       Transcribing | mark in the metadata.   |                         |
+ *                    | Copy the block mark     |                         |
+ *                    | into the first byte of  |                         |
+ *                    | the OOB.                |                         |
+ *       -------------+-------------------------+-------------------------+
+ *
+ * Note that we break rule #4 in the Transcribing/Raw case because we're not
+ * giving an accurate view of the actual, physical bytes in the page (we're
+ * overwriting the block mark). That's OK because it's more important to follow
+ * rule #2.
+ *
+ * It turns out that knowing whether we want an "ECC-based" or "raw" read is not
+ * easy. When reading a page, for example, the NAND Flash MTD code calls our
+ * ecc.read_page or ecc.read_page_raw function. Thus, the fact that MTD wants an
+ * ECC-based or raw view of the page is implicit in which function it calls
+ * (there is a similar pair of ECC-based/raw functions for writing).
+ *
+ * Since MTD assumes the OOB is not covered by ECC, there is no pair of
+ * ECC-based/raw functions for reading or or writing the OOB. The fact that the
+ * caller wants an ECC-based or raw view of the page is not propagated down to
+ * this driver.
+ */
+static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+				int page, int sndcmd)
+{
+	struct gpmi_nand_data *this = chip->priv;
+
+	pr_debug("page number is %d\n", page);
+	/* clear the OOB buffer */
+	memset(chip->oob_poi, ~0, mtd->oobsize);
+
+	/* Read out the conventional OOB. */
+	chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
+	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	/*
+	 * Now, we want to make sure the block mark is correct. In the
+	 * Swapping/Raw case, we already have it. Otherwise, we need to
+	 * explicitly read it.
+	 */
+	if (!this->swap_block_mark) {
+		/* Read the block mark into the first byte of the OOB buffer. */
+		chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+		chip->oob_poi[0] = chip->read_byte(mtd);
+	}
+
+	/*
+	 * Return true, indicating that the next call to this function must send
+	 * a command.
+	 */
+	return true;
+}
+
+static int
+gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page)
+{
+	/*
+	 * The BCH will use all the (page + oob).
+	 * Our gpmi_hw_ecclayout can only prohibit the JFFS2 to write the oob.
+	 * But it can not stop some ioctls such MEMWRITEOOB which uses
+	 * MTD_OOB_PLACE. So We have to implement this function to prohibit
+	 * these ioctls too.
+	 */
+	return -EPERM;
+}
+
+static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	int block, ret = 0;
+	uint8_t *block_mark;
+	int column, page, status, chipnr;
+
+	/* Get block number */
+	block = (int)(ofs >> chip->bbt_erase_shift);
+	if (chip->bbt)
+		chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
+
+	/* Do we have a flash based bad block table ? */
+	if (chip->options & NAND_BBT_USE_FLASH)
+		ret = nand_update_bbt(mtd, ofs);
+	else {
+		chipnr = (int)(ofs >> chip->chip_shift);
+		chip->select_chip(mtd, chipnr);
+
+		column = this->swap_block_mark ? mtd->writesize : 0;
+
+		/* Write the block mark. */
+		block_mark = this->data_buffer_dma;
+		block_mark[0] = 0; /* bad block marker */
+
+		/* Shift to get page */
+		page = (int)(ofs >> chip->page_shift);
+
+		chip->cmdfunc(mtd, NAND_CMD_SEQIN, column, page);
+		chip->write_buf(mtd, block_mark, 1);
+		chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+
+		status = chip->waitfunc(mtd, chip);
+		if (status & NAND_STATUS_FAIL)
+			ret = -EIO;
+
+		chip->select_chip(mtd, -1);
+	}
+	if (!ret)
+		mtd->ecc_stats.badblocks++;
+
+	return ret;
+}
+
+static int __devinit nand_boot_set_geometry(struct gpmi_nand_data *this)
+{
+	struct boot_rom_geometry *geometry = &this->rom_geometry;
+
+	/*
+	 * Set the boot block stride size.
+	 *
+	 * In principle, we should be reading this from the OTP bits, since
+	 * that's where the ROM is going to get it. In fact, we don't have any
+	 * way to read the OTP bits, so we go with the default and hope for the
+	 * best.
+	 */
+	geometry->stride_size_in_pages = 64;
+
+	/*
+	 * Set the search area stride exponent.
+	 *
+	 * In principle, we should be reading this from the OTP bits, since
+	 * that's where the ROM is going to get it. In fact, we don't have any
+	 * way to read the OTP bits, so we go with the default and hope for the
+	 * best.
+	 */
+	geometry->search_area_stride_exponent = 2;
+	return 0;
+}
+
+static const char  *fingerprint = "STMP";
+static int __devinit mx23_check_transcription_stamp(struct gpmi_nand_data *this)
+{
+	struct boot_rom_geometry *rom_geo = &this->rom_geometry;
+	struct device *dev = this->dev;
+	struct mtd_info *mtd = &this->mtd;
+	struct nand_chip *chip = &this->nand;
+	unsigned int search_area_size_in_strides;
+	unsigned int stride;
+	unsigned int page;
+	loff_t byte;
+	uint8_t *buffer = chip->buffers->databuf;
+	int saved_chip_number;
+	int found_an_ncb_fingerprint = false;
+
+	/* Compute the number of strides in a search area. */
+	search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent;
+
+	saved_chip_number = this->current_chip;
+	chip->select_chip(mtd, 0);
+
+	/*
+	 * Loop through the first search area, looking for the NCB fingerprint.
+	 */
+	dev_dbg(dev, "Scanning for an NCB fingerprint...\n");
+
+	for (stride = 0; stride < search_area_size_in_strides; stride++) {
+		/* Compute the page and byte addresses. */
+		page = stride * rom_geo->stride_size_in_pages;
+		byte = page   * mtd->writesize;
+
+		dev_dbg(dev, "Looking for a fingerprint in page 0x%x\n", page);
+
+		/*
+		 * Read the NCB fingerprint. The fingerprint is four bytes long
+		 * and starts in the 12th byte of the page.
+		 */
+		chip->cmdfunc(mtd, NAND_CMD_READ0, 12, page);
+		chip->read_buf(mtd, buffer, strlen(fingerprint));
+
+		/* Look for the fingerprint. */
+		if (!memcmp(buffer, fingerprint, strlen(fingerprint))) {
+			found_an_ncb_fingerprint = true;
+			break;
+		}
+
+	}
+
+	chip->select_chip(mtd, saved_chip_number);
+
+	if (found_an_ncb_fingerprint)
+		dev_dbg(dev, "\tFound a fingerprint\n");
+	else
+		dev_dbg(dev, "\tNo fingerprint found\n");
+	return found_an_ncb_fingerprint;
+}
+
+/* Writes a transcription stamp. */
+static int __devinit mx23_write_transcription_stamp(struct gpmi_nand_data *this)
+{
+	struct device *dev = this->dev;
+	struct boot_rom_geometry *rom_geo = &this->rom_geometry;
+	struct mtd_info *mtd = &this->mtd;
+	struct nand_chip *chip = &this->nand;
+	unsigned int block_size_in_pages;
+	unsigned int search_area_size_in_strides;
+	unsigned int search_area_size_in_pages;
+	unsigned int search_area_size_in_blocks;
+	unsigned int block;
+	unsigned int stride;
+	unsigned int page;
+	loff_t       byte;
+	uint8_t      *buffer = chip->buffers->databuf;
+	int saved_chip_number;
+	int status;
+
+	/* Compute the search area geometry. */
+	block_size_in_pages = mtd->erasesize / mtd->writesize;
+	search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent;
+	search_area_size_in_pages = search_area_size_in_strides *
+					rom_geo->stride_size_in_pages;
+	search_area_size_in_blocks =
+		  (search_area_size_in_pages + (block_size_in_pages - 1)) /
+				    block_size_in_pages;
+
+	dev_dbg(dev, "Search Area Geometry :\n");
+	dev_dbg(dev, "\tin Blocks : %u\n", search_area_size_in_blocks);
+	dev_dbg(dev, "\tin Strides: %u\n", search_area_size_in_strides);
+	dev_dbg(dev, "\tin Pages  : %u\n", search_area_size_in_pages);
+
+	/* Select chip 0. */
+	saved_chip_number = this->current_chip;
+	chip->select_chip(mtd, 0);
+
+	/* Loop over blocks in the first search area, erasing them. */
+	dev_dbg(dev, "Erasing the search area...\n");
+
+	for (block = 0; block < search_area_size_in_blocks; block++) {
+		/* Compute the page address. */
+		page = block * block_size_in_pages;
+
+		/* Erase this block. */
+		dev_dbg(dev, "\tErasing block 0x%x\n", block);
+		chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
+		chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
+
+		/* Wait for the erase to finish. */
+		status = chip->waitfunc(mtd, chip);
+		if (status & NAND_STATUS_FAIL)
+			dev_err(dev, "[%s] Erase failed.\n", __func__);
+	}
+
+	/* Write the NCB fingerprint into the page buffer. */
+	memset(buffer, ~0, mtd->writesize);
+	memset(chip->oob_poi, ~0, mtd->oobsize);
+	memcpy(buffer + 12, fingerprint, strlen(fingerprint));
+
+	/* Loop through the first search area, writing NCB fingerprints. */
+	dev_dbg(dev, "Writing NCB fingerprints...\n");
+	for (stride = 0; stride < search_area_size_in_strides; stride++) {
+		/* Compute the page and byte addresses. */
+		page = stride * rom_geo->stride_size_in_pages;
+		byte = page   * mtd->writesize;
+
+		/* Write the first page of the current stride. */
+		dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page);
+		chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
+		chip->ecc.write_page_raw(mtd, chip, buffer);
+		chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+
+		/* Wait for the write to finish. */
+		status = chip->waitfunc(mtd, chip);
+		if (status & NAND_STATUS_FAIL)
+			dev_err(dev, "[%s] Write failed.\n", __func__);
+	}
+
+	/* Deselect chip 0. */
+	chip->select_chip(mtd, saved_chip_number);
+	return 0;
+}
+
+static int __devinit mx23_boot_init(struct gpmi_nand_data  *this)
+{
+	struct device *dev = this->dev;
+	struct nand_chip *chip = &this->nand;
+	struct mtd_info *mtd = &this->mtd;
+	unsigned int block_count;
+	unsigned int block;
+	int     chipnr;
+	int     page;
+	loff_t  byte;
+	uint8_t block_mark;
+	int     ret = 0;
+
+	/*
+	 * If control arrives here, we can't use block mark swapping, which
+	 * means we're forced to use transcription. First, scan for the
+	 * transcription stamp. If we find it, then we don't have to do
+	 * anything -- the block marks are already transcribed.
+	 */
+	if (mx23_check_transcription_stamp(this))
+		return 0;
+
+	/*
+	 * If control arrives here, we couldn't find a transcription stamp, so
+	 * so we presume the block marks are in the conventional location.
+	 */
+	dev_dbg(dev, "Transcribing bad block marks...\n");
+
+	/* Compute the number of blocks in the entire medium. */
+	block_count = chip->chipsize >> chip->phys_erase_shift;
+
+	/*
+	 * Loop over all the blocks in the medium, transcribing block marks as
+	 * we go.
+	 */
+	for (block = 0; block < block_count; block++) {
+		/*
+		 * Compute the chip, page and byte addresses for this block's
+		 * conventional mark.
+		 */
+		chipnr = block >> (chip->chip_shift - chip->phys_erase_shift);
+		page = block << (chip->phys_erase_shift - chip->page_shift);
+		byte = block <<  chip->phys_erase_shift;
+
+		/* Send the command to read the conventional block mark. */
+		chip->select_chip(mtd, chipnr);
+		chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
+		block_mark = chip->read_byte(mtd);
+		chip->select_chip(mtd, -1);
+
+		/*
+		 * Check if the block is marked bad. If so, we need to mark it
+		 * again, but this time the result will be a mark in the
+		 * location where we transcribe block marks.
+		 */
+		if (block_mark != 0xff) {
+			dev_dbg(dev, "Transcribing mark in block %u\n", block);
+			ret = chip->block_markbad(mtd, byte);
+			if (ret)
+				dev_err(dev, "Failed to mark block bad with "
+							"ret %d\n", ret);
+		}
+	}
+
+	/* Write the stamp that indicates we've transcribed the block marks. */
+	mx23_write_transcription_stamp(this);
+	return 0;
+}
+
+static int __devinit nand_boot_init(struct gpmi_nand_data  *this)
+{
+	nand_boot_set_geometry(this);
+
+	/* This is ROM arch-specific initilization before the BBT scanning. */
+	if (GPMI_IS_MX23(this))
+		return mx23_boot_init(this);
+	return 0;
+}
+
+static int __devinit gpmi_set_geometry(struct gpmi_nand_data *this)
+{
+	int ret;
+
+	/* Free the temporary DMA memory for reading ID. */
+	gpmi_free_dma_buffer(this);
+
+	/* Set up the NFC geometry which is used by BCH. */
+	ret = bch_set_geometry(this);
+	if (ret) {
+		pr_err("set geometry ret : %d\n", ret);
+		return ret;
+	}
+
+	/* Alloc the new DMA buffers according to the pagesize and oobsize */
+	return gpmi_alloc_dma_buffer(this);
+}
+
+static int gpmi_pre_bbt_scan(struct gpmi_nand_data  *this)
+{
+	int ret;
+
+	/* Set up swap_block_mark, must be set before the gpmi_set_geometry() */
+	if (GPMI_IS_MX23(this))
+		this->swap_block_mark = false;
+	else
+		this->swap_block_mark = true;
+
+	/* Set up the medium geometry */
+	ret = gpmi_set_geometry(this);
+	if (ret)
+		return ret;
+
+	/* NAND boot init, depends on the gpmi_set_geometry(). */
+	return nand_boot_init(this);
+}
+
+static int gpmi_scan_bbt(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	int ret;
+
+	/* Prepare for the BBT scan. */
+	ret = gpmi_pre_bbt_scan(this);
+	if (ret)
+		return ret;
+
+	/* use the default BBT implementation */
+	return nand_default_bbt(mtd);
+}
+
+void gpmi_nfc_exit(struct gpmi_nand_data *this)
+{
+	nand_release(&this->mtd);
+	gpmi_free_dma_buffer(this);
+}
+
+static int __devinit gpmi_nfc_init(struct gpmi_nand_data *this)
+{
+	struct gpmi_nand_platform_data *pdata = this->pdata;
+	struct mtd_info  *mtd = &this->mtd;
+	struct nand_chip *chip = &this->nand;
+	int ret;
+
+	/* init current chip */
+	this->current_chip	= -1;
+
+	/* init the MTD data structures */
+	mtd->priv		= chip;
+	mtd->name		= "gpmi-nand";
+	mtd->owner		= THIS_MODULE;
+
+	/* init the nand_chip{}, we don't support a 16-bit NAND Flash bus. */
+	chip->priv		= this;
+	chip->select_chip	= gpmi_select_chip;
+	chip->cmd_ctrl		= gpmi_cmd_ctrl;
+	chip->dev_ready		= gpmi_dev_ready;
+	chip->read_byte		= gpmi_read_byte;
+	chip->read_buf		= gpmi_read_buf;
+	chip->write_buf		= gpmi_write_buf;
+	chip->ecc.read_page	= gpmi_ecc_read_page;
+	chip->ecc.write_page	= gpmi_ecc_write_page;
+	chip->ecc.read_oob	= gpmi_ecc_read_oob;
+	chip->ecc.write_oob	= gpmi_ecc_write_oob;
+	chip->scan_bbt		= gpmi_scan_bbt;
+	chip->badblock_pattern	= &gpmi_bbt_descr;
+	chip->block_markbad	= gpmi_block_markbad;
+	chip->options		|= NAND_NO_SUBPAGE_WRITE;
+	chip->ecc.mode		= NAND_ECC_HW;
+	chip->ecc.size		= 1;
+	chip->ecc.layout	= &gpmi_hw_ecclayout;
+
+	/* Allocate a temporary DMA buffer for reading ID in the nand_scan() */
+	this->bch_geometry.payload_size = 1024;
+	this->bch_geometry.auxiliary_size = 128;
+	ret = gpmi_alloc_dma_buffer(this);
+	if (ret)
+		goto err_out;
+
+	ret = nand_scan(mtd, pdata->max_chip_count);
+	if (ret) {
+		pr_err("Chip scan failed\n");
+		goto err_out;
+	}
+
+	ret = mtd_device_parse_register(mtd, NULL, NULL,
+			pdata->partitions, pdata->partition_count);
+	if (ret)
+		goto err_out;
+	return 0;
+
+err_out:
+	gpmi_nfc_exit(this);
+	return ret;
+}
+
+static int __devinit gpmi_nand_probe(struct platform_device *pdev)
+{
+	struct gpmi_nand_platform_data *pdata = pdev->dev.platform_data;
+	struct gpmi_nand_data *this;
+	int ret;
+
+	this = kzalloc(sizeof(*this), GFP_KERNEL);
+	if (!this) {
+		pr_err("Failed to allocate per-device memory\n");
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, this);
+	this->pdev  = pdev;
+	this->dev   = &pdev->dev;
+	this->pdata = pdata;
+
+	if (pdata->platform_init) {
+		ret = pdata->platform_init();
+		if (ret)
+			goto platform_init_error;
+	}
+
+	ret = acquire_resources(this);
+	if (ret)
+		goto exit_acquire_resources;
+
+	ret = init_hardware(this);
+	if (ret)
+		goto exit_nfc_init;
+
+	ret = gpmi_nfc_init(this);
+	if (ret)
+		goto exit_nfc_init;
+
+	return 0;
+
+exit_nfc_init:
+	release_resources(this);
+platform_init_error:
+exit_acquire_resources:
+	platform_set_drvdata(pdev, NULL);
+	kfree(this);
+	return ret;
+}
+
+static int __exit gpmi_nand_remove(struct platform_device *pdev)
+{
+	struct gpmi_nand_data *this = platform_get_drvdata(pdev);
+
+	gpmi_nfc_exit(this);
+	release_resources(this);
+	platform_set_drvdata(pdev, NULL);
+	kfree(this);
+	return 0;
+}
+
+static const struct platform_device_id gpmi_ids[] = {
+	{
+		.name = "imx23-gpmi-nand",
+		.driver_data = IS_MX23,
+	}, {
+		.name = "imx28-gpmi-nand",
+		.driver_data = IS_MX28,
+	}, {},
+};
+
+static struct platform_driver gpmi_nand_driver = {
+	.driver = {
+		.name = "gpmi-nand",
+	},
+	.probe   = gpmi_nand_probe,
+	.remove  = __exit_p(gpmi_nand_remove),
+	.id_table = gpmi_ids,
+};
+
+static int __init gpmi_nand_init(void)
+{
+	int err;
+
+	err = platform_driver_register(&gpmi_nand_driver);
+	if (err == 0)
+		printk(KERN_INFO "GPMI NAND driver registered. (IMX)\n");
+	else
+		pr_err("i.MX GPMI NAND driver registration failed\n");
+	return err;
+}
+
+static void __exit gpmi_nand_exit(void)
+{
+	platform_driver_unregister(&gpmi_nand_driver);
+}
+
+module_init(gpmi_nand_init);
+module_exit(gpmi_nand_exit);
+
+MODULE_AUTHOR("Freescale Semiconductor, Inc.");
+MODULE_DESCRIPTION("i.MX GPMI NAND Flash Controller Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h
new file mode 100644
index 0000000..e023bcc
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h
@@ -0,0 +1,273 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#ifndef __DRIVERS_MTD_NAND_GPMI_NAND_H
+#define __DRIVERS_MTD_NAND_GPMI_NAND_H
+
+#include <linux/mtd/nand.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <mach/dma.h>
+
+struct resources {
+	void          *gpmi_regs;
+	void          *bch_regs;
+	unsigned int  bch_low_interrupt;
+	unsigned int  bch_high_interrupt;
+	unsigned int  dma_low_channel;
+	unsigned int  dma_high_channel;
+	struct clk    *clock;
+};
+
+/**
+ * struct bch_geometry - BCH geometry description.
+ * @gf_len:                   The length of Galois Field. (e.g., 13 or 14)
+ * @ecc_strength:             A number that describes the strength of the ECC
+ *                            algorithm.
+ * @page_size:                The size, in bytes, of a physical page, including
+ *                            both data and OOB.
+ * @metadata_size:            The size, in bytes, of the metadata.
+ * @ecc_chunk_size:           The size, in bytes, of a single ECC chunk. Note
+ *                            the first chunk in the page includes both data and
+ *                            metadata, so it's a bit larger than this value.
+ * @ecc_chunk_count:          The number of ECC chunks in the page,
+ * @payload_size:             The size, in bytes, of the payload buffer.
+ * @auxiliary_size:           The size, in bytes, of the auxiliary buffer.
+ * @auxiliary_status_offset:  The offset into the auxiliary buffer at which
+ *                            the ECC status appears.
+ * @block_mark_byte_offset:   The byte offset in the ECC-based page view at
+ *                            which the underlying physical block mark appears.
+ * @block_mark_bit_offset:    The bit offset into the ECC-based page view at
+ *                            which the underlying physical block mark appears.
+ */
+struct bch_geometry {
+	unsigned int  gf_len;
+	unsigned int  ecc_strength;
+	unsigned int  page_size;
+	unsigned int  metadata_size;
+	unsigned int  ecc_chunk_size;
+	unsigned int  ecc_chunk_count;
+	unsigned int  payload_size;
+	unsigned int  auxiliary_size;
+	unsigned int  auxiliary_status_offset;
+	unsigned int  block_mark_byte_offset;
+	unsigned int  block_mark_bit_offset;
+};
+
+/**
+ * struct boot_rom_geometry - Boot ROM geometry description.
+ * @stride_size_in_pages:        The size of a boot block stride, in pages.
+ * @search_area_stride_exponent: The logarithm to base 2 of the size of a
+ *                               search area in boot block strides.
+ */
+struct boot_rom_geometry {
+	unsigned int  stride_size_in_pages;
+	unsigned int  search_area_stride_exponent;
+};
+
+/* DMA operations types */
+enum dma_ops_type {
+	DMA_FOR_COMMAND = 1,
+	DMA_FOR_READ_DATA,
+	DMA_FOR_WRITE_DATA,
+	DMA_FOR_READ_ECC_PAGE,
+	DMA_FOR_WRITE_ECC_PAGE
+};
+
+/**
+ * struct nand_timing - Fundamental timing attributes for NAND.
+ * @data_setup_in_ns:         The data setup time, in nanoseconds. Usually the
+ *                            maximum of tDS and tWP. A negative value
+ *                            indicates this characteristic isn't known.
+ * @data_hold_in_ns:          The data hold time, in nanoseconds. Usually the
+ *                            maximum of tDH, tWH and tREH. A negative value
+ *                            indicates this characteristic isn't known.
+ * @address_setup_in_ns:      The address setup time, in nanoseconds. Usually
+ *                            the maximum of tCLS, tCS and tALS. A negative
+ *                            value indicates this characteristic isn't known.
+ * @gpmi_sample_delay_in_ns:  A GPMI-specific timing parameter. A negative value
+ *                            indicates this characteristic isn't known.
+ * @tREA_in_ns:               tREA, in nanoseconds, from the data sheet. A
+ *                            negative value indicates this characteristic isn't
+ *                            known.
+ * @tRLOH_in_ns:              tRLOH, in nanoseconds, from the data sheet. A
+ *                            negative value indicates this characteristic isn't
+ *                            known.
+ * @tRHOH_in_ns:              tRHOH, in nanoseconds, from the data sheet. A
+ *                            negative value indicates this characteristic isn't
+ *                            known.
+ */
+struct nand_timing {
+	int8_t  data_setup_in_ns;
+	int8_t  data_hold_in_ns;
+	int8_t  address_setup_in_ns;
+	int8_t  gpmi_sample_delay_in_ns;
+	int8_t  tREA_in_ns;
+	int8_t  tRLOH_in_ns;
+	int8_t  tRHOH_in_ns;
+};
+
+struct gpmi_nand_data {
+	/* System Interface */
+	struct device		*dev;
+	struct platform_device	*pdev;
+	struct gpmi_nand_platform_data	*pdata;
+
+	/* Resources */
+	struct resources	resources;
+
+	/* Flash Hardware */
+	struct nand_timing	timing;
+
+	/* BCH */
+	struct bch_geometry	bch_geometry;
+	struct completion	bch_done;
+
+	/* NAND Boot issue */
+	bool			swap_block_mark;
+	struct boot_rom_geometry rom_geometry;
+
+	/* MTD / NAND */
+	struct nand_chip	nand;
+	struct mtd_info		mtd;
+
+	/* General-use Variables */
+	int			current_chip;
+	unsigned int		command_length;
+
+	/* passed from upper layer */
+	uint8_t			*upper_buf;
+	int			upper_len;
+
+	/* for DMA operations */
+	bool			direct_dma_map_ok;
+
+	struct scatterlist	cmd_sgl;
+	char			*cmd_buffer;
+
+	struct scatterlist	data_sgl;
+	char			*data_buffer_dma;
+
+	void			*page_buffer_virt;
+	dma_addr_t		page_buffer_phys;
+	unsigned int		page_buffer_size;
+
+	void			*payload_virt;
+	dma_addr_t		payload_phys;
+
+	void			*auxiliary_virt;
+	dma_addr_t		auxiliary_phys;
+
+	/* DMA channels */
+#define DMA_CHANS		8
+	struct dma_chan		*dma_chans[DMA_CHANS];
+	struct mxs_dma_data	dma_data;
+	enum dma_ops_type	last_dma_type;
+	enum dma_ops_type	dma_type;
+	struct completion	dma_done;
+
+	/* private */
+	void			*private;
+};
+
+/**
+ * struct gpmi_nfc_hardware_timing - GPMI hardware timing parameters.
+ * @data_setup_in_cycles:      The data setup time, in cycles.
+ * @data_hold_in_cycles:       The data hold time, in cycles.
+ * @address_setup_in_cycles:   The address setup time, in cycles.
+ * @use_half_periods:          Indicates the clock is running slowly, so the
+ *                             NFC DLL should use half-periods.
+ * @sample_delay_factor:       The sample delay factor.
+ */
+struct gpmi_nfc_hardware_timing {
+	uint8_t  data_setup_in_cycles;
+	uint8_t  data_hold_in_cycles;
+	uint8_t  address_setup_in_cycles;
+	bool     use_half_periods;
+	uint8_t  sample_delay_factor;
+};
+
+/**
+ * struct timing_threshod - Timing threshold
+ * @max_data_setup_cycles:       The maximum number of data setup cycles that
+ *                               can be expressed in the hardware.
+ * @internal_data_setup_in_ns:   The time, in ns, that the NFC hardware requires
+ *                               for data read internal setup. In the Reference
+ *                               Manual, see the chapter "High-Speed NAND
+ *                               Timing" for more details.
+ * @max_sample_delay_factor:     The maximum sample delay factor that can be
+ *                               expressed in the hardware.
+ * @max_dll_clock_period_in_ns:  The maximum period of the GPMI clock that the
+ *                               sample delay DLL hardware can possibly work
+ *                               with (the DLL is unusable with longer periods).
+ *                               If the full-cycle period is greater than HALF
+ *                               this value, the DLL must be configured to use
+ *                               half-periods.
+ * @max_dll_delay_in_ns:         The maximum amount of delay, in ns, that the
+ *                               DLL can implement.
+ * @clock_frequency_in_hz:       The clock frequency, in Hz, during the current
+ *                               I/O transaction. If no I/O transaction is in
+ *                               progress, this is the clock frequency during
+ *                               the most recent I/O transaction.
+ */
+struct timing_threshod {
+	const unsigned int      max_chip_count;
+	const unsigned int      max_data_setup_cycles;
+	const unsigned int      internal_data_setup_in_ns;
+	const unsigned int      max_sample_delay_factor;
+	const unsigned int      max_dll_clock_period_in_ns;
+	const unsigned int      max_dll_delay_in_ns;
+	unsigned long           clock_frequency_in_hz;
+
+};
+
+/* Common Services */
+extern int common_nfc_set_geometry(struct gpmi_nand_data *);
+extern struct dma_chan *get_dma_chan(struct gpmi_nand_data *);
+extern void prepare_data_dma(struct gpmi_nand_data *,
+				enum dma_data_direction dr);
+extern int start_dma_without_bch_irq(struct gpmi_nand_data *,
+				struct dma_async_tx_descriptor *);
+extern int start_dma_with_bch_irq(struct gpmi_nand_data *,
+				struct dma_async_tx_descriptor *);
+
+/* GPMI-NAND helper function library */
+extern int gpmi_init(struct gpmi_nand_data *);
+extern void gpmi_clear_bch(struct gpmi_nand_data *);
+extern void gpmi_dump_info(struct gpmi_nand_data *);
+extern int bch_set_geometry(struct gpmi_nand_data *);
+extern int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip);
+extern int gpmi_send_command(struct gpmi_nand_data *);
+extern void gpmi_begin(struct gpmi_nand_data *);
+extern void gpmi_end(struct gpmi_nand_data *);
+extern int gpmi_read_data(struct gpmi_nand_data *);
+extern int gpmi_send_data(struct gpmi_nand_data *);
+extern int gpmi_send_page(struct gpmi_nand_data *,
+			dma_addr_t payload, dma_addr_t auxiliary);
+extern int gpmi_read_page(struct gpmi_nand_data *,
+			dma_addr_t payload, dma_addr_t auxiliary);
+
+/* BCH : Status Block Completion Codes */
+#define STATUS_GOOD		0x00
+#define STATUS_ERASED		0xff
+#define STATUS_UNCORRECTABLE	0xfe
+
+/* Use the platform_id to distinguish different Archs. */
+#define IS_MX23			0x1
+#define IS_MX28			0x2
+#define GPMI_IS_MX23(x)		((x)->pdev->id_entry->driver_data == IS_MX23)
+#define GPMI_IS_MX28(x)		((x)->pdev->id_entry->driver_data == IS_MX28)
+#endif
-- 
1.7.0.4