From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [RFC 08/11] ARM: Kirkwood: Convert GoFlex Net to pinctrl.
Date: Sat, 20 Oct 2012 15:11:37 -0000 [thread overview]
Message-ID: <1350745663-5277-9-git-send-email-andrew@lunn.ch> (raw)
In-Reply-To: <1350745663-5277-1-git-send-email-andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood-goflexnet.dts | 57 ++++++++++++++++++++++++++++++
arch/arm/mach-kirkwood/board-goflexnet.c | 18 ----------
2 files changed, 57 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index 7c8238f..46d16a2 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -16,6 +16,63 @@
};
ocp at f1000000 {
+ pinctrl: pinctrl at 10000 {
+ compatible = "marvell,88f6281-pinctrl";
+ reg = <0x10000 0x20>;
+
+ pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+ &pmx_led_left_cap_0 &pmx_led_left_cap_1
+ &pmx_led_left_cap_2 &pmx_led_left_cap_3
+ &pmx_led_right_cap_0 &pmx_led_right_cap_1
+ &pmx_led_right_cap_2 &pmx_led_right_cap_3
+ >;
+ pinctrl-names = "default";
+
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_0: pmx-led_right_cap_0 {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_1: pmx-led_right_cap_1 {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_2: pmx-led_right_cap_2 {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_3: pmx-led_right_cap_3 {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_0: pmx-led_left_cap_0 {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_1: pmx-led_left_cap_1 {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_2: pmx-led_left_cap_2 {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_3: pmx-led_left_cap_3 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led_orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
serial at 12000 {
clock-frequency = <200000000>;
status = "ok";
diff --git a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c
index 001ca8c..9643f4b 100644
--- a/arch/arm/mach-kirkwood/board-goflexnet.c
+++ b/arch/arm/mach-kirkwood/board-goflexnet.c
@@ -34,34 +34,16 @@
#include <mach/bridge-regs.h>
#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
-#include "mpp.h"
static struct mv643xx_eth_platform_data goflexnet_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(0),
};
-static unsigned int goflexnet_mpp_config[] __initdata = {
- MPP29_GPIO, /* USB Power Enable */
- MPP47_GPIO, /* LED Orange */
- MPP46_GPIO, /* LED Green */
- MPP45_GPIO, /* LED Left Capacity 3 */
- MPP44_GPIO, /* LED Left Capacity 2 */
- MPP43_GPIO, /* LED Left Capacity 1 */
- MPP42_GPIO, /* LED Left Capacity 0 */
- MPP41_GPIO, /* LED Right Capacity 3 */
- MPP40_GPIO, /* LED Right Capacity 2 */
- MPP39_GPIO, /* LED Right Capacity 1 */
- MPP38_GPIO, /* LED Right Capacity 0 */
- 0
-};
-
void __init goflexnet_init(void)
{
/*
* Basic setup. Needs to be called early.
*/
- kirkwood_mpp_conf(goflexnet_mpp_config);
-
if (gpio_request(29, "USB Power Enable") != 0 ||
gpio_direction_output(29, 1) != 0)
pr_err("can't setup GPIO 29 (USB Power Enable)\n");
--
1.7.10.4
next prev parent reply other threads:[~2012-10-20 15:11 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-20 15:07 [RFC 00/11] Convert Kirkwood to pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 07/11] ARM: Kirkwood: Convert dreamplug " Andrew Lunn
2012-10-20 15:11 ` [RFC 06/11] ARM: Kirkwood: Convert dockstar " Andrew Lunn
2012-10-20 15:11 ` [RFC 05/11] ARM: Kirkwood: Convert dnskw " Andrew Lunn
2012-10-20 15:11 ` [RFC 02/11] ARM: Kirkwood: Allow use of MVEBU GPIO driver Andrew Lunn
2012-10-20 15:11 ` [RFC 01/11] ARM: Kirkwood: Allow use of pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 03/11] ARM: Kirkwood: Convert TS219 to pinctrl Andrew Lunn
2012-10-20 15:11 ` [RFC 04/11] ARM: Kirkwood: Convert iConnect " Andrew Lunn
2012-10-20 15:11 ` Andrew Lunn [this message]
2012-10-20 15:11 ` [RFC 09/11] ARM: Kirkwood: Convert ib62x0 " Andrew Lunn
2012-10-20 15:11 ` [RFC 10/11] ARM: Kirkwood: Convert lsxl boards " Andrew Lunn
2012-10-20 15:11 ` [RFC 11/11] ARM: Kirkwood: Convert IX2-200 " Andrew Lunn
[not found] ` <20121021115716.GA22437@schnuecks.de>
2012-10-21 17:57 ` [RFC 00/11] Convert Kirkwood " Andrew Lunn
2012-10-21 19:09 ` Thomas Petazzoni
2012-10-21 19:16 ` Andrew Lunn
2012-10-21 21:11 ` Sebastian Hesselbarth
2012-10-22 4:54 ` Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1350745663-5277-9-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.