From: Shubhrajyoti D <shubhrajyoti@ti.com> To: linux-omap@vger.kernel.org Cc: linux-i2c@vger.kernel.org, linux-arm-kernel@lists.infradead.org, ben-linux@fluff.org, tony@atomide.com, w.sang@pengutronix.de, Shubhrajyoti D <shubhrajyoti@ti.com> Subject: [PATCH 1/2] i2c: omap: re-factor omap_i2c_init function Date: Thu, 25 Oct 2012 15:53:05 +0530 [thread overview] Message-ID: <1351160586-12306-2-git-send-email-shubhrajyoti@ti.com> (raw) In-Reply-To: <1351160586-12306-1-git-send-email-shubhrajyoti@ti.com> re-factor omap_i2c_init() so that we can re-use it for resume. While at it also remove the bufstate variable as we write it in omap_i2c_resize_fifo for every transfer. Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> --- drivers/i2c/busses/i2c-omap.c | 71 ++++++++++++++++++---------------------- 1 files changed, 32 insertions(+), 39 deletions(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 5e5cefb..3d400b1 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -209,7 +209,6 @@ struct omap_i2c_dev { u16 pscstate; u16 scllstate; u16 sclhstate; - u16 bufstate; u16 syscstate; u16 westate; u16 errata; @@ -285,9 +284,31 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg) } } +static void __omap_i2c_init(struct omap_i2c_dev *dev) +{ + + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); + /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */ + omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate); + + /* SCL low and high time values */ + omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, dev->scllstate); + omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, dev->sclhstate); + if (dev->rev >= OMAP_I2C_REV_ON_3430_3530) + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate); + /* Take the I2C module out of reset: */ + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); + /* + * Don't write to this register if the IE state is 0 as it can + * cause deadlock. + */ + if (dev->iestate) + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate); +} + static int omap_i2c_init(struct omap_i2c_dev *dev) { - u16 psc = 0, scll = 0, sclh = 0, buf = 0; + u16 psc = 0, scll = 0, sclh = 0; u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0; unsigned long fclk_rate = 12000000; unsigned long timeout; @@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) * REVISIT: Some wkup sources might not be needed. */ dev->westate = OMAP_I2C_WE_ALL; - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, - dev->westate); } } - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); if (dev->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) { /* @@ -426,28 +444,18 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) sclh = fclk_rate / (dev->speed * 2) - 7 + psc; } - /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */ - omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, psc); - - /* SCL low and high time values */ - omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, scll); - omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, sclh); - - /* Take the I2C module out of reset: */ - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); - /* Enable interrupts */ dev->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY | OMAP_I2C_IE_NACK | OMAP_I2C_IE_AL) | ((dev->fifo_size) ? (OMAP_I2C_IE_RDR | OMAP_I2C_IE_XDR) : 0); - omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate); - if (dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { - dev->pscstate = psc; - dev->scllstate = scll; - dev->sclhstate = sclh; - dev->bufstate = buf; - } + + dev->pscstate = psc; + dev->scllstate = scll; + dev->sclhstate = sclh; + + __omap_i2c_init(dev); + return 0; } @@ -1268,23 +1276,8 @@ static int omap_i2c_runtime_resume(struct device *dev) { struct omap_i2c_dev *_dev = dev_get_drvdata(dev); - if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, 0); - omap_i2c_write_reg(_dev, OMAP_I2C_PSC_REG, _dev->pscstate); - omap_i2c_write_reg(_dev, OMAP_I2C_SCLL_REG, _dev->scllstate); - omap_i2c_write_reg(_dev, OMAP_I2C_SCLH_REG, _dev->sclhstate); - omap_i2c_write_reg(_dev, OMAP_I2C_BUF_REG, _dev->bufstate); - omap_i2c_write_reg(_dev, OMAP_I2C_SYSC_REG, _dev->syscstate); - omap_i2c_write_reg(_dev, OMAP_I2C_WE_REG, _dev->westate); - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); - } - - /* - * Don't write to this register if the IE state is 0 as it can - * cause deadlock. - */ - if (_dev->iestate) - omap_i2c_write_reg(_dev, OMAP_I2C_IE_REG, _dev->iestate); + if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) + __omap_i2c_init(_dev); return 0; } -- 1.7.5.4
WARNING: multiple messages have this Message-ID (diff)
From: shubhrajyoti@ti.com (Shubhrajyoti D) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 1/2] i2c: omap: re-factor omap_i2c_init function Date: Thu, 25 Oct 2012 15:53:05 +0530 [thread overview] Message-ID: <1351160586-12306-2-git-send-email-shubhrajyoti@ti.com> (raw) In-Reply-To: <1351160586-12306-1-git-send-email-shubhrajyoti@ti.com> re-factor omap_i2c_init() so that we can re-use it for resume. While at it also remove the bufstate variable as we write it in omap_i2c_resize_fifo for every transfer. Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> --- drivers/i2c/busses/i2c-omap.c | 71 ++++++++++++++++++---------------------- 1 files changed, 32 insertions(+), 39 deletions(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 5e5cefb..3d400b1 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -209,7 +209,6 @@ struct omap_i2c_dev { u16 pscstate; u16 scllstate; u16 sclhstate; - u16 bufstate; u16 syscstate; u16 westate; u16 errata; @@ -285,9 +284,31 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg) } } +static void __omap_i2c_init(struct omap_i2c_dev *dev) +{ + + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); + /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */ + omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate); + + /* SCL low and high time values */ + omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, dev->scllstate); + omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, dev->sclhstate); + if (dev->rev >= OMAP_I2C_REV_ON_3430_3530) + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate); + /* Take the I2C module out of reset: */ + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); + /* + * Don't write to this register if the IE state is 0 as it can + * cause deadlock. + */ + if (dev->iestate) + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate); +} + static int omap_i2c_init(struct omap_i2c_dev *dev) { - u16 psc = 0, scll = 0, sclh = 0, buf = 0; + u16 psc = 0, scll = 0, sclh = 0; u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0; unsigned long fclk_rate = 12000000; unsigned long timeout; @@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) * REVISIT: Some wkup sources might not be needed. */ dev->westate = OMAP_I2C_WE_ALL; - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, - dev->westate); } } - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); if (dev->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) { /* @@ -426,28 +444,18 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) sclh = fclk_rate / (dev->speed * 2) - 7 + psc; } - /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */ - omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, psc); - - /* SCL low and high time values */ - omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, scll); - omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, sclh); - - /* Take the I2C module out of reset: */ - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); - /* Enable interrupts */ dev->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY | OMAP_I2C_IE_NACK | OMAP_I2C_IE_AL) | ((dev->fifo_size) ? (OMAP_I2C_IE_RDR | OMAP_I2C_IE_XDR) : 0); - omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate); - if (dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { - dev->pscstate = psc; - dev->scllstate = scll; - dev->sclhstate = sclh; - dev->bufstate = buf; - } + + dev->pscstate = psc; + dev->scllstate = scll; + dev->sclhstate = sclh; + + __omap_i2c_init(dev); + return 0; } @@ -1268,23 +1276,8 @@ static int omap_i2c_runtime_resume(struct device *dev) { struct omap_i2c_dev *_dev = dev_get_drvdata(dev); - if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, 0); - omap_i2c_write_reg(_dev, OMAP_I2C_PSC_REG, _dev->pscstate); - omap_i2c_write_reg(_dev, OMAP_I2C_SCLL_REG, _dev->scllstate); - omap_i2c_write_reg(_dev, OMAP_I2C_SCLH_REG, _dev->sclhstate); - omap_i2c_write_reg(_dev, OMAP_I2C_BUF_REG, _dev->bufstate); - omap_i2c_write_reg(_dev, OMAP_I2C_SYSC_REG, _dev->syscstate); - omap_i2c_write_reg(_dev, OMAP_I2C_WE_REG, _dev->westate); - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); - } - - /* - * Don't write to this register if the IE state is 0 as it can - * cause deadlock. - */ - if (_dev->iestate) - omap_i2c_write_reg(_dev, OMAP_I2C_IE_REG, _dev->iestate); + if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) + __omap_i2c_init(_dev); return 0; } -- 1.7.5.4
next prev parent reply other threads:[~2012-10-25 10:23 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2012-10-25 10:23 [PATCH 0/2] i2c: omap: cleanups Shubhrajyoti D 2012-10-25 10:23 ` Shubhrajyoti D 2012-10-25 10:23 ` Shubhrajyoti D [this message] 2012-10-25 10:23 ` [PATCH 1/2] i2c: omap: re-factor omap_i2c_init function Shubhrajyoti D 2012-10-25 10:52 ` Felipe Balbi 2012-10-25 10:52 ` Felipe Balbi 2012-10-25 10:23 ` [PATCH 2/2] i2c: omap: make reset a seperate function Shubhrajyoti D 2012-10-25 10:23 ` Shubhrajyoti D [not found] ` <1351160586-12306-3-git-send-email-shubhrajyoti-l0cyMroinI0@public.gmane.org> 2012-10-25 10:55 ` Felipe Balbi 2012-10-25 10:55 ` Felipe Balbi [not found] ` <20121025105516.GH21217-S8G//mZuvNWo5Im9Ml3/Zg@public.gmane.org> 2012-10-25 13:47 ` Shubhrajyoti 2012-10-25 13:47 ` Shubhrajyoti
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1351160586-12306-2-git-send-email-shubhrajyoti@ti.com \ --to=shubhrajyoti@ti.com \ --cc=ben-linux@fluff.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-i2c@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=tony@atomide.com \ --cc=w.sang@pengutronix.de \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.