From: Thomas Abraham <thomas.abraham@linaro.org> To: spi-devel-general@lists.sourceforge.net Cc: linux-arm-kernel@lists.infradead.org, grant.likely@secretlab.ca, linus.walleij@linaro.org, linux-samsung-soc@vger.kernel.org, kgene.kim@samsung.com, t.figa@samsung.com, heiko@sntech.de, jaswinder.singh@linaro.org, patches@linaro.org Subject: [PATCH] spi: s3c64xx: let device core setup the default pin configuration Date: Wed, 06 Mar 2013 17:12:10 +0530 [thread overview] Message-ID: <1362570130-14084-1-git-send-email-thomas.abraham@linaro.org> (raw) With device core now able to setup the default pin configuration, the pin configuration code based on the deprecated Samsung specific gpio bindings is removed. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> --- .../devicetree/bindings/spi/spi-samsung.txt | 8 +-- drivers/spi/spi-s3c64xx.c | 66 +------------------ 2 files changed, 6 insertions(+), 68 deletions(-) diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index a15ffed..86aa061 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -31,9 +31,6 @@ Required Board Specific Properties: - #address-cells: should be 1. - #size-cells: should be 0. -- gpios: The gpio specifier for clock, mosi and miso interface lines (in the - order specified). The format of the gpio specifier depends on the gpio - controller. Optional Board Specific Properties: @@ -86,9 +83,8 @@ Example: spi_0: spi@12d20000 { #address-cells = <1>; #size-cells = <0>; - gpios = <&gpa2 4 2 3 0>, - <&gpa2 6 2 3 0>, - <&gpa2 7 2 3 0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_bus>; w25q80bw@0 { #address-cells = <1>; diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index e862ab8..8537b17 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -1052,41 +1052,6 @@ static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel) } #ifdef CONFIG_OF -static int s3c64xx_spi_parse_dt_gpio(struct s3c64xx_spi_driver_data *sdd) -{ - struct device *dev = &sdd->pdev->dev; - int idx, gpio, ret; - - /* find gpios for mosi, miso and clock lines */ - for (idx = 0; idx < 3; idx++) { - gpio = of_get_gpio(dev->of_node, idx); - if (!gpio_is_valid(gpio)) { - dev_err(dev, "invalid gpio[%d]: %d\n", idx, gpio); - goto free_gpio; - } - sdd->gpios[idx] = gpio; - ret = gpio_request(gpio, "spi-bus"); - if (ret) { - dev_err(dev, "gpio [%d] request failed: %d\n", - gpio, ret); - goto free_gpio; - } - } - return 0; - -free_gpio: - while (--idx >= 0) - gpio_free(sdd->gpios[idx]); - return -EINVAL; -} - -static void s3c64xx_spi_dt_gpio_free(struct s3c64xx_spi_driver_data *sdd) -{ - unsigned int idx; - for (idx = 0; idx < 3; idx++) - gpio_free(sdd->gpios[idx]); -} - static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) { struct s3c64xx_spi_info *sci; @@ -1119,15 +1084,6 @@ static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) { return dev->platform_data; } - -static int s3c64xx_spi_parse_dt_gpio(struct s3c64xx_spi_driver_data *sdd) -{ - return -EINVAL; -} - -static void s3c64xx_spi_dt_gpio_free(struct s3c64xx_spi_driver_data *sdd) -{ -} #endif static const struct of_device_id s3c64xx_spi_dt_match[]; @@ -1247,10 +1203,7 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) goto err0; } - if (!sci->cfg_gpio && pdev->dev.of_node) { - if (s3c64xx_spi_parse_dt_gpio(sdd)) - return -EBUSY; - } else if (sci->cfg_gpio == NULL || sci->cfg_gpio()) { + if (sci->cfg_gpio && sci->cfg_gpio()) { dev_err(&pdev->dev, "Unable to config gpio\n"); ret = -EBUSY; goto err0; @@ -1261,13 +1214,13 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) if (IS_ERR(sdd->clk)) { dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n"); ret = PTR_ERR(sdd->clk); - goto err1; + goto err0; } if (clk_prepare_enable(sdd->clk)) { dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n"); ret = -EBUSY; - goto err1; + goto err0; } sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr); @@ -1324,9 +1277,6 @@ err3: clk_disable_unprepare(sdd->src_clk); err2: clk_disable_unprepare(sdd->clk); -err1: - if (!sdd->cntrlr_info->cfg_gpio && pdev->dev.of_node) - s3c64xx_spi_dt_gpio_free(sdd); err0: platform_set_drvdata(pdev, NULL); spi_master_put(master); @@ -1349,9 +1299,6 @@ static int s3c64xx_spi_remove(struct platform_device *pdev) clk_disable_unprepare(sdd->clk); - if (!sdd->cntrlr_info->cfg_gpio && pdev->dev.of_node) - s3c64xx_spi_dt_gpio_free(sdd); - platform_set_drvdata(pdev, NULL); spi_master_put(master); @@ -1370,9 +1317,6 @@ static int s3c64xx_spi_suspend(struct device *dev) clk_disable_unprepare(sdd->src_clk); clk_disable_unprepare(sdd->clk); - if (!sdd->cntrlr_info->cfg_gpio && dev->of_node) - s3c64xx_spi_dt_gpio_free(sdd); - sdd->cur_speed = 0; /* Output Clock is stopped */ return 0; @@ -1384,9 +1328,7 @@ static int s3c64xx_spi_resume(struct device *dev) struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); struct s3c64xx_spi_info *sci = sdd->cntrlr_info; - if (!sci->cfg_gpio && dev->of_node) - s3c64xx_spi_parse_dt_gpio(sdd); - else + if (sci->cfg_gpio) sci->cfg_gpio(); /* Enable the clock */ -- 1.6.6.rc2
WARNING: multiple messages have this Message-ID (diff)
From: thomas.abraham@linaro.org (Thomas Abraham) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH] spi: s3c64xx: let device core setup the default pin configuration Date: Wed, 06 Mar 2013 17:12:10 +0530 [thread overview] Message-ID: <1362570130-14084-1-git-send-email-thomas.abraham@linaro.org> (raw) With device core now able to setup the default pin configuration, the pin configuration code based on the deprecated Samsung specific gpio bindings is removed. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> --- .../devicetree/bindings/spi/spi-samsung.txt | 8 +-- drivers/spi/spi-s3c64xx.c | 66 +------------------ 2 files changed, 6 insertions(+), 68 deletions(-) diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index a15ffed..86aa061 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -31,9 +31,6 @@ Required Board Specific Properties: - #address-cells: should be 1. - #size-cells: should be 0. -- gpios: The gpio specifier for clock, mosi and miso interface lines (in the - order specified). The format of the gpio specifier depends on the gpio - controller. Optional Board Specific Properties: @@ -86,9 +83,8 @@ Example: spi_0: spi at 12d20000 { #address-cells = <1>; #size-cells = <0>; - gpios = <&gpa2 4 2 3 0>, - <&gpa2 6 2 3 0>, - <&gpa2 7 2 3 0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_bus>; w25q80bw at 0 { #address-cells = <1>; diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index e862ab8..8537b17 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -1052,41 +1052,6 @@ static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel) } #ifdef CONFIG_OF -static int s3c64xx_spi_parse_dt_gpio(struct s3c64xx_spi_driver_data *sdd) -{ - struct device *dev = &sdd->pdev->dev; - int idx, gpio, ret; - - /* find gpios for mosi, miso and clock lines */ - for (idx = 0; idx < 3; idx++) { - gpio = of_get_gpio(dev->of_node, idx); - if (!gpio_is_valid(gpio)) { - dev_err(dev, "invalid gpio[%d]: %d\n", idx, gpio); - goto free_gpio; - } - sdd->gpios[idx] = gpio; - ret = gpio_request(gpio, "spi-bus"); - if (ret) { - dev_err(dev, "gpio [%d] request failed: %d\n", - gpio, ret); - goto free_gpio; - } - } - return 0; - -free_gpio: - while (--idx >= 0) - gpio_free(sdd->gpios[idx]); - return -EINVAL; -} - -static void s3c64xx_spi_dt_gpio_free(struct s3c64xx_spi_driver_data *sdd) -{ - unsigned int idx; - for (idx = 0; idx < 3; idx++) - gpio_free(sdd->gpios[idx]); -} - static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) { struct s3c64xx_spi_info *sci; @@ -1119,15 +1084,6 @@ static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) { return dev->platform_data; } - -static int s3c64xx_spi_parse_dt_gpio(struct s3c64xx_spi_driver_data *sdd) -{ - return -EINVAL; -} - -static void s3c64xx_spi_dt_gpio_free(struct s3c64xx_spi_driver_data *sdd) -{ -} #endif static const struct of_device_id s3c64xx_spi_dt_match[]; @@ -1247,10 +1203,7 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) goto err0; } - if (!sci->cfg_gpio && pdev->dev.of_node) { - if (s3c64xx_spi_parse_dt_gpio(sdd)) - return -EBUSY; - } else if (sci->cfg_gpio == NULL || sci->cfg_gpio()) { + if (sci->cfg_gpio && sci->cfg_gpio()) { dev_err(&pdev->dev, "Unable to config gpio\n"); ret = -EBUSY; goto err0; @@ -1261,13 +1214,13 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) if (IS_ERR(sdd->clk)) { dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n"); ret = PTR_ERR(sdd->clk); - goto err1; + goto err0; } if (clk_prepare_enable(sdd->clk)) { dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n"); ret = -EBUSY; - goto err1; + goto err0; } sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr); @@ -1324,9 +1277,6 @@ err3: clk_disable_unprepare(sdd->src_clk); err2: clk_disable_unprepare(sdd->clk); -err1: - if (!sdd->cntrlr_info->cfg_gpio && pdev->dev.of_node) - s3c64xx_spi_dt_gpio_free(sdd); err0: platform_set_drvdata(pdev, NULL); spi_master_put(master); @@ -1349,9 +1299,6 @@ static int s3c64xx_spi_remove(struct platform_device *pdev) clk_disable_unprepare(sdd->clk); - if (!sdd->cntrlr_info->cfg_gpio && pdev->dev.of_node) - s3c64xx_spi_dt_gpio_free(sdd); - platform_set_drvdata(pdev, NULL); spi_master_put(master); @@ -1370,9 +1317,6 @@ static int s3c64xx_spi_suspend(struct device *dev) clk_disable_unprepare(sdd->src_clk); clk_disable_unprepare(sdd->clk); - if (!sdd->cntrlr_info->cfg_gpio && dev->of_node) - s3c64xx_spi_dt_gpio_free(sdd); - sdd->cur_speed = 0; /* Output Clock is stopped */ return 0; @@ -1384,9 +1328,7 @@ static int s3c64xx_spi_resume(struct device *dev) struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); struct s3c64xx_spi_info *sci = sdd->cntrlr_info; - if (!sci->cfg_gpio && dev->of_node) - s3c64xx_spi_parse_dt_gpio(sdd); - else + if (sci->cfg_gpio) sci->cfg_gpio(); /* Enable the clock */ -- 1.6.6.rc2
next reply other threads:[~2013-03-06 11:42 UTC|newest] Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top 2013-03-06 11:42 Thomas Abraham [this message] 2013-03-06 11:42 ` [PATCH] spi: s3c64xx: let device core setup the default pin configuration Thomas Abraham 2013-03-07 8:11 ` Linus Walleij 2013-03-07 8:11 ` Linus Walleij 2013-03-11 17:36 ` Doug Anderson 2013-03-11 17:36 ` Doug Anderson 2013-04-15 17:23 ` Doug Anderson 2013-04-15 17:23 ` Doug Anderson 2013-04-15 18:27 ` Linus Walleij 2013-04-15 18:27 ` Linus Walleij 2013-04-16 3:42 ` [REPOST PATCH] " Doug Anderson 2013-04-16 3:42 ` Doug Anderson 2013-04-16 10:24 ` Grant Likely 2013-04-16 10:24 ` Grant Likely 2013-04-16 10:24 ` Grant Likely
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1362570130-14084-1-git-send-email-thomas.abraham@linaro.org \ --to=thomas.abraham@linaro.org \ --cc=grant.likely@secretlab.ca \ --cc=heiko@sntech.de \ --cc=jaswinder.singh@linaro.org \ --cc=kgene.kim@samsung.com \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-samsung-soc@vger.kernel.org \ --cc=patches@linaro.org \ --cc=spi-devel-general@lists.sourceforge.net \ --cc=t.figa@samsung.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.